首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 406 毫秒
1.
Self‐centering reinforced concrete frames are developed as an alternative of traditional seismic force‐resisting systems with better seismic performance and re‐centering capability. This paper presents an experimental and computational study on the seismic performance of self‐centering reinforced concrete frames. A 1/2‐scale model of a two‐story self‐centering reinforced concrete frame model was designed and tested on the shaking table in State Key Laboratory of Disaster Reduction in Civil Engineering at Tongji University to evaluate the seismic behavior of the structure. A structural analysis model, including detailed modeling of beam–column joints, column–base joints, and prestressed tendons, was constructed in the nonlinear dynamic modeling software OpenSEES. Agreements between test results and numerical solutions indicate that the designed reinforced concrete frame has satisfactory seismic performance and self‐centering capacity subjected to earthquakes; the self‐centering structures can undergo large rocking with minor residual displacement after the earthquake excitations; the proposed analysis procedure can be applied in simulating the seismic performance of self‐centering reinforced concrete frames. To achieve a more comprehensive evaluation on the performance of self‐centering structures, research on energy dissipation devices in the system is expected. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

2.
This paper deals with the seismic response assessment of an old reinforced concrete viaduct and the effectiveness of friction‐based retrofitting systems. Emphasis was laid on an old bridge, not properly designed to resist seismic action, consisting of 12 portal piers that support a 13‐span bay deck for each independent roadway. On the basis of an OpenSEES finite element frame pier model, calibrated in a previous experimental campaign with cyclic displacement on three 1:4 scale frame piers, a more complex experimental activity using hybrid simulation has been devised. The aim of the simulation was twofold: (i) to increase knowledge of non‐linear behavior of reinforced concrete frame piers with plain steel rebars and detailing dating from the late 1950s; and (ii) to study the effectiveness of sliding bearings for seismic response mitigation. Hence, to explore the performance of the as built bridge layout and also of the viaduct retrofitted with friction‐based devices, at both serviceability and ultimate limit state conditions, hybrid simulation tests were carried out. In particular, two frame piers were experimentally controlled with eight‐actuator channels in the as built case while two frame piers and eight sliding bearings were controlled with 18‐actuator channels in the isolated case. The remaining frame piers were part of numerical substructures and were updated offline to accurately track damage evolution. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

3.
在地震作用下中小跨径梁桥横向易出现落梁以及桥墩破坏。为了防止桥梁出现上述震害,提出以楔形挡块作为限位装置来提升桥梁的横向抗震性能。以一座3×20 m连续混凝土梁桥为例,通过OpenSees软件来建立有限元模型,在考虑板式橡胶支座的摩擦滑移效应、钢筋混凝土桥墩的非线性等力学效应的情况下,对其进行动力时程分析。引入主梁位移响应、桥墩顶部最大位移响应等作为指标,用柔性挡块、刚性挡块两种工况来与楔形挡块进行对比分析,并且分析楔形挡块不同角度对位移响应的影响。结果表明:楔形挡块角度设置合适时能够有效约束梁体位移响应,并且不显著提高桥墩顶部的位移响应。  相似文献   

4.
The seismic damages commonly observed on beam–column joints of old reinforced concrete structures, built with plain bars and without proper detailing, justifies the need to further study the behaviour of this type of structures. The response of these structures when loaded cyclically, as occurs during the earthquakes, is partially controlled by the bond properties between the reinforcing bars and the surrounding concrete. This paper presents the results of an experimental campaign of unidirectional cyclic tests carried out on six full‐scale beam–column joints built with plain bars. These joint specimens are representative of existing reinforced concrete structures, that is, built without adequate reinforcement detailing for seismic demands. For comparison, an additional specimen is built with deformed bars and tested. The seven specimens are designed and detailed to allow the investigation of the influence of bond properties, lapping of the longitudinal bars in columns and beams, bent‐up bars in the beams, slab contribution and concrete strength. The lateral force–drift relationships, global dissipated energy evolution, contribution of the joint, beams and columns to the global dissipated energy, ductility, equivalent damping, final damage observed, homogenized reinforced concrete damage index, displacement components, curvature evolutions and Eurocode requirements are presented and discussed. Copyright © 2014 John Wiley & Sons, Ltd.  相似文献   

5.
This paper discusses the importance of including the bond‐slip effects in assessing the response under cyclic loads of reinforced concrete frames. The discussion is based on analyses performed using numerical models which are simple, computationally efficient and capable of representing the salient features of reinforced concrete frames under both static and dynamic loads. The numerical models comprise a displacement‐based, reinforced concrete frame element with bond‐slip and a rigid beam column joint element with bond‐slip. Two applications illustrate the model accuracy and show the importance of including bond‐slip. The first application considers a reinforced concrete beam‐column subassemblage experimentally tested under cyclic loads. The second application considers the shaking table test of a two‐story one‐bay reinforced concrete frame In both cases the analytical results correlate well with the experimental results in terms of strength, displacement demands and hysteretic energy dissipation. Furthermore, the paper shows how the analyses that include bond‐slip yield a better correlation with the experimental results with respect to the analyses that assume a perfect bond. Copyright © 2003 John Wiley & Sons, Ltd.  相似文献   

6.
By means of a simplified three degrees of freedom model, seismic behavior of reinforced concrete bridge piers and foundations were evaluated based on pseudo‐dynamic (PsD) tests for cases where pier strengthening and foundation strengthening are implemented. In addition, analysis based on PsD test results was conducted to investigate the influence of pier strengthening on seismic damage to the foundation. The PsD tests and the analysis show that the foundation suffers increased hysteretic response when pier strengthening is applied. The results also show that the foundation strengthening can prevent foundation damage. Copyright © 2011 John Wiley & Sons, Ltd.  相似文献   

7.
Experimental proof is provided of an unconventional seismic design concept, which is based on deliberately underdesigning shallow foundations to promote intense rocking oscillations and thereby to dramatically improve the seismic resilience of structures. Termed rocking isolation, this new seismic design philosophy is investigated through a series of dynamic centrifuge experiments on properly scaled models of a modern reinforced concrete (RC) bridge pier. The experimental method reproduces the nonlinear and inelastic response of both the soil‐footing interface and the structure. To this end, a novel scale model RC (1:50 scale) that simulates reasonably well the elastic response and the failure of prototype RC elements is utilized, along with realistic representation of the soil behavior in a geotechnical centrifuge. A variety of seismic ground motions are considered as excitations. They result in consistent demonstrably beneficial performance of the rocking‐isolated pier in comparison with the one designed conventionally. Seismic demand is reduced in terms of both inertial load and deck drift. Furthermore, foundation uplifting has a self‐centering potential, whereas soil yielding is shown to provide a particularly effective energy dissipation mechanism, exhibiting significant resistance to cumulative damage. Thanks to such mechanisms, the rocking pier survived, with no signs of structural distress, a deleterious sequence of seismic motions that caused collapse of the conventionally designed pier. © 2014 The Authors Earthquake Engineering & Structural Dynamics Published by John Wiley & Sons Ltd.  相似文献   

8.
Earthquake simulator tests of a 1/6-scale nine-story reinforced concrete frame-wall model are described in the paper. The test results and associated numerical simulation are summarized and discussed. Based on the test data, a relationship between maximum inter-story drift and damage state is established. Equations of variation of structural characteristics (natural frequency and equivalent stiffness) with overall drifts are derived by data fitting, which can be used to estimate structural damage state if structural characteristics can be measured. A comparison of the analytical and experimental results show that both the commonly used equivalent beam and fiber element models can simulate the nonlinear seismic response of structures very well. Finally, conclusions associated with seismic design and damage evaluation of RC structures are presented.  相似文献   

9.
The aim of this work is to model beam‐column behavior in a computationally effective manner, revealing reliably the overall response of reinforced concrete members subjected to intensive seismic loading. In this respect, plasticity and damage are considered in the predominant longitudinal direction, allowing for fiber finite element modeling, while in addition the effect of inelastic buckling of longitudinal rebars, which becomes essential at later stages of intensive cyclic loading, is incorporated. Α smooth plasticity‐damage model is developed for concrete, accounting for unilateral compressive and tensile behavior, nonlinear unloading and crack closure phenomena. This is used to address concrete core crushing and spalling, which triggers the inelastic buckling of longitudinal rebars. For this reason, a uniaxial local stress‐strain constitutive relation for steel rebars is developed, which is based on a combined nonlinear kinematic and isotropic hardening law. The proposed constitutive model is validated on the basis of existing experimental data and the formulation of the buckling model for a single rebar is developed. The cross section of rebar is discretized into fibers, each one following the derived stress‐strain uniaxial law. The buckling curve is determined analytically, while equilibrium is imposed at the deformed configuration. The proposed models for concrete and rebars are embedded into a properly adjusted fiber beam‐column element of reinforced concrete members and the proposed formulation is verified with existing experimental data under intensive cyclic loading.  相似文献   

10.
为了全面研究工程水泥基复合材料（ECC）加固桥墩的抗震性能,对采用聚乙烯醇纤维增强水泥基复合材料（PVA-ECC）加固的桥墩进行了拟静力试验。并基于有限元分析软件OpenSees建立了数值模型,通过对比数值模拟结果与试验结果,验证有限元分析的有效性,在此基础上对PVA-ECC加固桥墩进行数值参数分析,探讨轴压比、新旧材料厚径比及体积配箍率变化对桥墩抗震性能的影响规律。结果表明:数值模拟的滞回曲线与骨架曲线和试验基本吻合;与普通混凝土桥墩相比,新旧材料厚径比为0.10时,即可获得优异的延性性能,ECC加固的桥墩变形性能显著提升,极限位移提高,滞回曲线更加饱满,抗震性能更加优异。对于高轴压比情况,为了确保ECC加固桥墩的延性性能,应根据实际情况增加新旧材料厚径比;ECC材料可部分替代箍筋作用,适用于箍筋配置不足的桥墩加固,PVA-ECC具有较好的工程抗震加固的作用。  相似文献   

11.
The nonlinear behavior of reinforced concrete (RC) members represents a key issue in the seismic performance assessment of structures. Many structures constructed in the 1980s or earlier were designed based on force limits; thus they often exhibit brittle failure modes, strength and stiffness degradation, and severe pinching effects. Field surveys and experimental evidence have demonstrated that such inelastic responses affect the global behavior of RC structural systems. Efforts have been made to consider the degrading stiffness and strength in the simplified nonlinear static procedures commonly adopted by practitioners. This paper investigates the accuracy of such procedures for the seismic performance assessment of RC structural systems. Refined finite element models of a shear critical bridge bent and a flexure‐critical bridge pier are used as reference models. The numerical models are validated against experimental results and used to evaluate the inelastic dynamic response of the structures subjected to earthquake ground motions with increasing amplitude. The maximum response from the refined numerical models is compared against the results from the simplified static procedures, namely modified capacity spectrum method and coefficient method in FEMA‐440. The accuracy of the static procedures in estimating the displacement demand of a flexure‐critical system and shear‐critical system is discussed in detail. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

12.
A beam–column‐type finite element for seismic assessment of reinforced concrete (R/C) frame structures is presented. This finite element consists of two interacting, distributed flexibility sub‐elements representing inelastic flexural and shear response. Following this formulation, the proposed model is able to capture spread of flexural yielding, as well as spread of shear cracking, in R/C members. The model accounts for shear strength degradation with inelastic curvature demand, as well as coupling between inelastic flexural and shear deformations after flexural yielding, observed in many experimental studies. An empirical relationship is proposed for evaluating the average shear distortion of R/C columns at the onset of stirrup yielding. The proposed numerical model is validated against experimental results involving R/C columns subjected to cyclic loading. It is shown that the model can predict well the hysteretic response of R/C columns with different failure modes, i.e. flexure‐critical elements, elements failing in shear after flexural yielding, and shear‐critical R/C members. Copyright © 2008 John Wiley & Sons, Ltd.  相似文献   

13.
Nonstructural reinforced concrete flat walls architecturally designed as exterior/partition walls in concrete buildings were severely damaged by the 2011 earthquake off the Pacific coast of Tohoku. This damage was observed in the monolithic nonstructural flat walls of relatively old ductile concrete buildings. Although these flat walls might affect the overall seismic performance and behavior of a building, the nonstructural wall effects have not been clarified because of the complex interactions among the structural components. To understand these effects, this paper conducts an experimental and numerical investigation of the nonstructural wall effects, focusing on a typical residential building damaged by the 2011 earthquake. A single‐story, one‐bay moment‐resisting frame model of the building with a nonstructural flat wall was tested to clarify the fundamental behavior. The results reveal that the wall significantly contributed to the seismic performance of the overall frame until it failed in shear, subsequently losing structural effectiveness. Such experimental wall behavior could be simulated by the isoparametric element model. Moreover, the structural effects of the nonstructural flat walls on the global seismic performance and behavior of the investigated building were discussed through earthquake response analyses using ground motions recorded near the building site and pushover analyses. Consequently, the building damage could be simulated in an analytical case considering the nonstructural flat walls, showing larger inter‐story drifts in the lower stories due to softening of the walls. The analytical results also indicated that the softening of the nonstructural flat walls decreased the building ductility, as defined by ultimate inter‐story drifts. Copyright © 2017 John Wiley & Sons, Ltd.  相似文献   

14.
The seismic response of non‐ductile reinforced concrete (RC) buildings can be affected by the behaviour of beam‐column joints involved in the failure mechanism, especially in typical existing buildings. Conventional modelling approaches consider only beam and column flexibility, although joints can provide a significant contribution also to the overall frame deformability. In this study, the attention is focused on exterior joints without transverse reinforcement, and a possible approach to their modelling in nonlinear seismic analysis of RC frames is proposed. First, experimental tests performed by the authors are briefly presented, and their results are discussed. Second, these tests, together with other tests with similar features from literature, are employed to calibrate the joint panel deformability contribution in order to reproduce numerically the experimental joint shear stress–strain behaviour under cyclic loading. After a validation phase of this proposal, a numerical investigation of the influence of joints on the seismic behaviour of a case study RC frame – designed for gravity loads only – is performed. The preliminary failure mode classification of the joints within the analysed frame is carried out. Structural models that (i) explicitly include nonlinear behaviour of beam‐column joints exhibiting shear or anchorage failure or (ii) model joints as elements with infinite strength and stiffness are built and their seismic performance are assessed and compared. A probabilistic assessment based on nonlinear dynamic simulations is performed by means of a scaling approach to evaluate the seismic response at different damage states accounting for uncertainties in ground‐motion records. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

15.
The 2012 Emilia earthquake (in Northern Italy) caused extensive damage to existing prefabricated reinforced concrete structures. These buildings were found being extremely vulnerable because, being designed for vertical loads only, they featured friction‐based connections between structural elements, most commonly between beams and columns. Given the large diffusion of these structures, their seismic retrofit is critical. Various techniques have been proposed in the literature, in most of which friction‐based connections are removed by inserting mechanical connectors that will make beam‐column connections hinged. These approaches lead to a significant increase of the base shear and therefore require strengthening of columns. The paper presents dissipative devices based on carbon‐wrapped steel tubes to be used as an alternative low‐damage solution for the retrofit of beam‐column connections. The first part of the paper presents results of experimental tests on the devices and discusses their dissipative behaviour. The succeeding parts of the paper present numerical analyses on simple structures reinforced with the proposed device. The results of the numerical study show how the introduction of the dissipative devices produces a significant reduction of forces transmitted to the structure, by comparing the seismic response of simple frame structures equipped with dissipative devices with the response of equivalent elastic systems.  相似文献   

16.
The seismic resistance characteristics of a newly developed composite bridge pier system are examined via a series of experimental studies. In this innovative bridge pier system, the shear strength is provided by the steel tube and the concrete confined by the steel tube. No transverse shear reinforcement is used in this system. Axial and flexural strengths of the bridge pier are exerted by the longitudinal reinforcements and the concrete. A gap between the end of steel tube and the reinforced concrete foundation contributes to the steel tube providing shear resistance only without sharing the flexural moment. From the experimental results of this study, it is found that the flexural strength of the proposed composite bridge pier can be predicted accurately by the conventional method that was used in the reinforced concrete structures. Shear strength of the composite bridge pier can be obtained by summing up shear strengths of the concrete and the steel tube. Excellent deformation capacities are also found from the experimental studies. The proposed composite bridge pier system not only simplifies the construction work greatly, but also provides superior seismic resistance as compared with that of the conventional method. Copyright © 2010 John Wiley & Sons, Ltd.  相似文献   

17.
The reinforced concrete frame‐core tube structure is a common form of high‐rise building; however, certain vertical components of these structures are prone to be damaged by earthquakes, debris flow, or other accidents, leaving no time for repair or retrofit. This study is motivated by a practical problem—that is, the seismic vulnerability and collapse resistant capability under future earthquakes when a vertical member has failed. A reduced scale model (1:15 scale) of a typical reinforced concrete frame‐core tube with a corner column removed from the first floor is designed, fabricated, and tested. The corner column is replaced by a jack, and the failure behavior is simulated by manually unloading the jack. The model is then excited by a variety of seismic ground motions on the shaking table. Experimental results concerning the seismic responses and actual process of collapse are presented herein. Finally, the earthquake‐induced collapse process is simulated numerically using the software program ANSYS/LS‐DYNA. Validation and calibration of the model are carried out by comparison with the experimental results. Furthermore, based on both experimental investigations and numerical simulations, the collapse mechanism is discussed, and some suggestions on collapse design are put forward. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

18.
This paper reports a study for the seismic performance of one large‐scaled (1/15) model of 30‐story steel‐reinforced concrete frame‐concrete core wall mixed structure. The study was implemented by both shaking table tests, in which the similarity ratio for lateral and gravitational accelerations was kept to 1:1, and numerical nonlinear dynamic analysis. The test observations presented herein include story displacement, interstory drift, natural vibration periods, and final failure mode. The numerical analysis was performed to simulate the shaking table test procedure, and the numerically obtained responses were verified by the test results. On the basis of the numerical results, the progressions of structural stiffness, base shear, and overturning moment were investigated, and the distributions of base shear and overturning moment between frame and core wall were also discussed. The test demonstrates the seismic performance of the steel‐reinforced concrete frame‐core wall mixed structure and reveals the potential overturning failure mode for high rise structures. The nonlinear analysis results indicate that the peripheral frames could take more shear forces after core wall damaged under severe earthquakes. Copyright © 2013 John Wiley & Sons, Ltd.  相似文献   

19.
Evaluating the inelastic seismic response of structures accurately is of great importance in earthquake engineering and generally requires refined simulation, which is a time‐consuming process. Because the material nonlinearity generally occurs in a small part of the whole structure, many researches focus on taking advantage of this characteristic to improve the computational efficiency and the inelasticity‐separated finite element method (IS‐FEM) proposed recently provide a generic finite element formulation for solving this kind of problems efficiently. Although the fiber beam‐column element is widely used for the simulation of reinforced concrete (RC) framed structures, the inelastic deformation is often detected in a large part of the numerical model under earthquake excitation so that it is hard to achieve high efficient computation when applying the IS‐FEM to the inelastic response analysis of RC fiber models directly. In this paper, a new numerical scheme for seismic response analysis of RC framed structures model by fiber beam‐column element is proposed based on the IS‐FEM. To implement the RC fiber model for use in IS‐FEM and improve the computational performance of proposed scheme, a method of identifying the local domains with severe section inelasticity level is proposed and a modified Kent‐Park concrete material model is developed. Because the Woodbury formula is adopted as the solver, the global stiffness matrix can keep unchanged throughout the analysis and the main computational effort is only invested on a small matrix representing local inelastic behavior. The numerical examples demonstrate the validity and efficiency of the proposed scheme.  相似文献   

20.
The inelastic seismic torsional response of simple structures is examined by means of shear‐beam type models as well as with plastic hinge idealization of one‐story buildings. Using mean values of ductility factors, obtained for groups of ten earthquake motions, as the basic index of post‐elastic response, the following topics are examined with the shear‐beam type model: mass eccentric versus stiffness eccentric systems, effects of different types of motions and effects of double eccentricities. Subsequently, comparisons are made with results obtained using a more realistic, plastic hinge type model of single‐story reinforced concrete frame buildings designed according to a modern Code. The consequences of designing for different levels of accidental eccentricity are also examined for the aforementioned frame buildings. Copyright © 2003 John Wiley & Sons, Ltd.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号