首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 500 毫秒
1.
Water shortage and groundwater pollution have become two primary environmental concerns to Beijing since the 1990s. The local aquifers, as the dominant sources for domestic and agricultural water supply, are depleting due to groundwater abstraction and continuous drought in recent years with rapid urbanization and increasing water consumption. Therefore, understanding the hydrogeological system is fundamental for a sustainable water resources management. In this article, the numerical analysis of a 3-D regional groundwater flow model for the Nankou area is presented. The hydrogeological system is reproduced according to sparsely distributed boreholes data. The numerical analysis is carried out using the scientific software OpenGeoSys, which is based on the finite element method. The model calibration and sensitivity analysis are accomplished with inverse methods by applying a model independent parameter estimation system (PEST). The results of the calibrated model show reasonable agreements with observed water levels. The transient groundwater flow simulations reflect the observed drawdown of the last 9 years and show the formation of a depression cone in an intensively pumped area.  相似文献   

2.
In this work, a 3D groundwater flow model integrating all important geological features of the hydrogeological system is developed to investigate hydrological processes in the Wadi Kafrein area of Jordan. A large amount of available geological and hydrological data is integrated to construct a 3D groundwater flow model for the Wadi Kafrein area. Using the newly developed mapping approach, the translation of the highly detailed geological formations to an unstructured finite element grids, can be accomplished with high precision. The existing data set for model calibration is scarce, which is a typical situation for many hydrogeological case studies. At first, the steady state calibration of the groundwater model is carried out based on the observation wells. Then, the time and space-dependent recharge from precipitation are applied at the top surface of the finite element model. The transient simulation is conducted during the period of 1996–2008 considering the abstraction rates of the production wells and discharge of the springs. The calculated water levels are close to the observed values. The difference is partly caused by return flows from irrigation and the groundwater inflow from the adjacent aquifers which are not taken into consideration so far. Since the Wadi Kafrein area is an important agricultural area in the semiarid region of the Lower Jordan Valley, the model developed in this study can be regarded as a useful tool for analyzing the hydrological processes and improving groundwater management practices elsewhere affected by similar geological and hydrogeological conditions.  相似文献   

3.
Ongoing developments in geological and hydrogeological investigation techniques, especially direct-push methods, have led to an increase in the quality, density and spatial resolution of data available from such investigations. This has created new challenges in the development of numerical models in terms of accurately and efficiently translating detailed and complex conceptual models into effective numerical models. Suitable geometrical and numerical modelling tools are essential in order to meet these challenges. This paper describes the development of a three-dimensional hydrogeological flow model for a contaminated site near Berlin, Germany, based on high-resolution geological data obtained principally using direct-push methods. The available data were first interpreted to construct a detailed GIS-based geological model, which formed the basis of the conceptual site model. The conceptual model was then translated into a geometrical model, which was used to create a finite element numerical model. An innovative geometry object-based approach enabled the complex structural details of the conceptual model to be accurately reproduced in the numerical model domain. The resulting three-dimensional steady-state unconfined flow model was successfully calibrated using external automated calibration software, whereby parameter values for groundwater recharge and hydraulic conductivity were determined.  相似文献   

4.
岛屿是我国领土的重要组成部分,对国家安全和国防军事意义非凡。岛屿的地下水资源尤为珍贵,地下水流场模拟是研究地下水分布规律的重要手段。水文地质条件复杂、可利用的观测井较少等原因,造成了基岩岛屿水文地质模型概化精度不高、初始条件难以获取等问题。为克服基岩岛屿地下水流场模拟的诸多困难,将珠海外伶仃岛作为研究区,利用数字高程模型数据开展地质地貌建模; 利用探地雷达法、直流电法与地质分析对岛屿进行探测,获取了地层数据; 采用地下水遥感评估法,利用实测井位数据,确定了地下水的初始水位,进而对基岩岛屿地下水流场进行建模; 最终,通过对外伶仃岛地下水流场的数值模拟得出地下水模拟流场图。岛上多个测点的探测水位值与模拟水位相关性较好,其拟合优度R2为0.872 2。由此可见,综合遥感、物探、水文地质手段等技术方法获取的数据,采用地下水模拟软件或程序实现基岩岛屿地下水流场的数值模拟,是基岩岛屿地下水资源研究的一个有效方法。  相似文献   

5.
Numerical simulation of groundwater flow used for the estimation of hydraulic and hydrologic parameters which is an important tool for the management of aquifers. This study presents the results of a mathematical model developed for the simulation of groundwater flow in Nahavand plain aquifer in the southwest Hamadan province. For this purpose Groundwater Modeling Software (GMS) was used which supports the MODFLOW-2000 code. After gathering required data such as the hydrological, hydrogeological and topography maps, a 3D hydrogeological model of plain was constructed with borehole and surface elevation data. Then MODFLOW was used for simulation of flow. After initial simulation of the flow, the model was calibrated in steady state with trial-and-error and parameter estimation methods the observed head of groundwater table monitoring data of 1997. Results of calibration show that error between observed head and computed head is in allowable range. Also results of computed head with model show that groundwater flow is in the direction of the dominate slope (southeast to northwest). Finally MODPATH code which simulates advective transport of particles was used for estimation of flow path and source of contaminants.  相似文献   

6.
依据铜陵太平-钟仓应急水源地水文地质条件构建水文地质概念模型.在此基础上,利用三维可视化软件GMS建立水源地地下水流数值模拟模型,并对模型进行了识别和验证.模型模拟期为一个应急供水周期180 d(2017-01~2017-06),水源地开采层位为承压水.模拟结果表明:在采用均匀布井方案和限定开采井水位降深不超过承压含水层顶板的条件下,水源地允许开采量为11.94×104 m3/d,达大型水源地规模(5×104 m3/d<允许开采量<15×104 m3/d);水源地承压水在应急开采条件下,激发了长江侧渗补给量,袭夺量占水源地开采总量的27.82%.同时,通过模型模拟数据对傍河水源地地下水与地表水转换规律进行了初步探讨.  相似文献   

7.
为了探究水文地质结构对地下水流数值模拟的不确定性,可以运用随机模拟建立地下水位的预测模型。根据转移概率地质统计方法模拟多孔介质岩性分布,利用非线性规划的思路计算岩性与水文地质参数之间的关系,从而建立相对精确的随机水文地质参数场。将不同的水文地质参数场运用到MODFLOW中,得到不同的随机模拟结果。通过比较随机模型和确定模型的末流场拟合情况以及水位动态拟合图,发现确定模型和随机模型具有相似趋势,都能与实测流场拟合较好,但是随机模型更能体现真实的水文地质特征。对随机模型预测10年后的地下水水位做不确定性分析,得到水位平均变幅介于-5~5 m之间,且95%置信度水位变幅的平均上限线约为0.146 m。研究结果为决策者提供科学依据。  相似文献   

8.
车灿辉 《探矿工程》2018,45(11):60-64
渗透系数决定了深基坑工程涌水量的估算及止水帷幕的型式,影响工程安全及造价,对富水地区深基坑工程建设具有重大的意义。对于非均质含水层组,现有的解析公式中,很难找到合适的方法计算水文地质参数,特别是垂直方向的渗透系数。通过在现场施作临时止水帷幕,利用帷幕的绕流阻水作用进行抽水试验,模拟基坑开挖过程中的降水问题,再建立水文地质概念模型和地下水流数学模型,并利用三维有限差分数值模拟软件反演出各层渗透系数,最后通过验证性抽水资料对模型进行了验证,为福州一临江巨厚砂卵石地层地铁车站的围护结构设计中地下水控制提供了设计参数。该试验和数值模拟结果可为类似工程参考。  相似文献   

9.
地下水流数值模拟是高放废物处置库选址中水文地质评价的重要内容.水文地质概念模型是地下水流数值模拟的基础和前提.在北山预选区水文地质分析基础上,利用DEM数据生成了研究区地表水系,据此确定了模拟范围;借助GMS软件,建立了研究区三维水文地质结构模型;再通过边界条件、流场特征、地下水均衡项和水文地质参数的分析和描述,建立了北山地区水文地质概念模型.  相似文献   

10.
Gropius  M.  Dahabiyeh  M.  Al Hyari  M.  Brückner  F.  Lindenmaier  F.  Vassolo  S. 《Hydrogeology Journal》2022,30(6):1769-1787

Jordan suffers from water scarcity and groundwater covers the majority of Jordan’s water supply. Therefore, there is an urgent need to manage this resource conscientiously. A regional numerical groundwater flow model, developed as part of a decision support system for the country of Jordan, allows for quantification of the overexploitation of groundwater resources and enables determination of the extent of unrecorded agricultural groundwater abstraction. Groundwater in Jordan is abstracted from three main aquifers partly separated by aquitards. With updated geological, structural, and hydrogeological data available in the country, a regional numerical groundwater flow model for the whole of Jordan and the southernmost part of Syria was developed using MODFLOW. It was first calibrated for a steady-state condition using data from the 1960s, when groundwater abstraction was negligible. After transient calibration using groundwater level measurements from all aquifers, model results reproduce the large groundwater-level declines experienced in the last decades, which have led to the drying out of numerous springs. They show a reversal of groundwater flow directions in some regions, due to over-abstraction, and demonstrate that documented abstractions are not sufficient to cause the observed groundwater-level decline. Only after considering irrigation water demand derived from remote sensing data, the model is able to simulate these declines. Illegal abstractions can be quantified and predictive scenarios show the potential impact of different management strategies on future groundwater resources.

  相似文献   

11.

A groundwater resource characterisation and assessment model was developed for Nasia river sub-basin in the White Volta Basin, Ghana. The model is useful to policymakers for planning and sustainable management of groundwater resources in the basin for domestic and irrigation purposes. A conceptual model was constructed that characterized boundary conditions and hydrostratigraphy, and estimated recharge rates and hydraulic and storage parameters. From current understanding of the hydrogeological dynamics, three hydrostratigraphic layers were delineated. The conceptual model was converted to a three-dimensional steady-state groundwater flow model using MODFLOW. Recharge rates estimated from the base model indicate a minimum of 1.1% and maximum of 6.2% of the total rainfall. The hydraulic conductivity ranged between 0.20 and 15 m/day. Four possible scenarios were simulated: (1) increased population, (2) climate variations (reduced recharge), (3) increased abstraction for irrigation, and (4) worst-case scenario which is a combination of the first three scenarios. Results from scenarios 1 and 2 indicated that, under such conditions, the groundwater resources could be sustained and no significant effect on any of the water budget indicators was observed. For scenario 3, there was significant drop in hydraulic head in the central portions of the study area. The scenario 4 simulation indicated that there was significant reduction in groundwater levels and groundwater discharge into streams under these stressors. Such reduction can affect stream levels in the basin and, subsequently, the ecosystem. These findings are valid within the limits of uncertainty in the hydrogeological data that were used in this study.

  相似文献   

12.
As established in the European Water Framework Directive, the development of groundwater numerical models is fundamental for adopting water management plans aimed at preserving the water resource and reducing environmental risks. In this paper, authors present a methodology for the estimation of groundwater resource of an alluvial valley, in an urban area characterized by a complex hydrostratigraphic setting and scarcity of hydrogeological data; the study area is the urban and sub-urban area of Rome (Italy). A previous, elaborated hydrostratigraphic model set the base for the development of 3D, steady state, sub-basin scale numerical model, implemented by the finite-difference code MODFLOW 2000®; the water system components were derived by elaboration of available data. The alluvial aquifer of the Tiber River Valley, which runs in the middle of the City in a NNW–SE direction, has been analyzed in detail, since it is covered by a densely populated area hosting most of Rome’s historical heritage, and it is characterized by low quality geotechnical parameters. Results suggest that in areas with high hydrostratigraphic complexity and scarcity of hydrogeological data, a sub-basin scale, and steady-state numerical model can be very helpful to verify the conceptual model and reduce the uncertainty on the water budget components. The proposed steady-state model constitutes the base for future applications of transient state and local scale models, required for sustainable water management.  相似文献   

13.
地下水流系统理论和数值模拟技术分别是水文地质学的基本理论和技术方法,含水岩组的概化是地下水流系统分析和地下水数值模拟的重要基础,直接影响着数值模拟和水流系统分析的精度和可信度.为提高含水岩组概化的精度和可信度,提出一种含水岩组概化的新方法,即累积导水系数法.依据岩层厚度与渗透系数乘积累积值随深度的变化,以及水文地质剖面岩性分布的整体特征,概化含水介质结构.以玛纳斯河流域为例,应用该方法概化流域内的岩性剖面,结合GMS软件中TINS模块构建水文地质结构模型.结果表明,应用该方法概化后的含水层结构具有较好的合理性和仿真性,建立的三维模型很好地显示了研究区含水介质的空间展布特征,为建立地下水流模型奠定了良好的基础.   相似文献   

14.
石家庄市东部平原FEFLOW地下水数值模拟与研究   总被引:2,自引:0,他引:2  
根据研究区水文地质条件、开采条件及资料条件,将研究区内水文地质概念模型概化为二维非均质、各向同性、非稳定地下水流系统.利用先进的FEFLOW有限元地下水模拟系统建立了研究区的区域地下水流模型,预测不同开采方案下的地下水动态变化,为地下水资源开发利用和优化配置提供科学依据.  相似文献   

15.
基于MODFLOW参数不确定性的地下水水流数值模拟方法   总被引:1,自引:0,他引:1  
考虑到模型不确定性引起的地下水数值模拟不确定性对模拟过程的影响,在简要介绍含水层水文地质参数变异性研究进展和地质统计学的基础上,基于常用的确定性地下水流数值模拟软件MODFLOW开发了MODFLOW-Gslib软件,相较于传统的数值模拟方法,将地质统计学与数值模拟结合的方法能够模拟非均质含水层中的参数变异性问题。将MODFLOW-Gslib软件运用于模拟实例中,选择常见的不确定性因素进行模拟,并对其模拟产生的数据进行统计分析,结果表明,软件转化后的参数符合水文地质参数不确定性的相关特征;与原模拟结果进行对比,该软件能够更加真实地刻画含水层参数变异性特征。  相似文献   

16.
济宁市地下水与地面沉降三维有限元模拟   总被引:1,自引:0,他引:1  
在分析济宁市水文地质条件的基础上 ,对引起地面沉降诸因素进行了分析 ,并建立了地面沉降量与地下水位变幅之间的相关关系。集中过量开采地下水是引起济宁市地面沉降的主要原因。在此基础上 ,建立了准三维地下水流模型和一维地面沉降模型。通过水力联系建立地下水与地面沉降耦合数值模型 ,运用有限元法对地下水渗流场和地面沉降量进行模拟 ,并对 2 0 0 0年和 2 0 10年地面沉降进行了预测  相似文献   

17.
针对现有地下水流模拟软件在数据预处理、三维可视化效果等方面的不足,以Visual C++ 6.0为主要开发环境、OpenGL为三维图形显示与渲染工具,以地下水及其赋存地质体观测记录为主要数据源,实现了数据处理、建模、存储、调度、查询以及真三维可视化,在此基础上完成了地下水动态模拟分析功能,实现了虚拟地理信息技术在地下水工作中的系统应用,具有功能开放、丰富、灵活的特点。  相似文献   

18.
通过分析新郑市水文地质条件,建立了概念模型,运用GMS软件建立三维地下水流的数值模拟模型,对研究区浅层地下水资源进行现状评价,并对2015年和2020年地下水位进行了预测.结果表明,研究区地下水水位持续下降,到2020年水位将会下降5~10 m,部分地区可能会出现开采漏斗,为了降低地下水位的下降幅度,应该调整产业结构,加强水资源的管理,提高水资源的利用率,从而减少地下水资源的开采.  相似文献   

19.
构建合理的水文地质概念模型对于地下水数值模拟至关重要,概念模型如果确定不合理,整个数值模拟将毫无意义。通常水文地质调查可以大致确定水文地质概念模型,然而对于一些不易被发现的补给源,通过水文地质调查也无法确定。水化学和同位素特征对地下水的补给源及水流路径有很好的指示作用,可以根据这些信息对水文地质概念模型进行细化。文章通过对研究区地下水取样,分析地下水水化学和同位素特征,确定出研究区内不易识别的地下水补给源及顶层黏土-粉质黏土的透水性,最终细化了水文地质概念模型边界条件。这对于后期得到正确的地下水流和溶质运移模拟结果具有重要意义。  相似文献   

20.
To deal with the challenge of groundwater over-extraction in arid and semi-arid environments, it is necessary to establish management strategies based on the knowledge of hydrogeological conditions, which can be difficult in places where hydrogeological data are dispersed, scarce or present potential misinformation. Groundwater levels in the southern Jordan Valley (Jordan) have decreased drastically in the last three decades, caused by over-extraction of groundwater for irrigation purposes. This study presents a local, two-dimensional and transient numerical groundwater model, using MODFLOW, to characterise the groundwater system and the water balance in the southern Jordan Valley. Furthermore, scenarios are simulated regarding hydrological conditions and management options, like extension of arable land and closure of illegal wells, influencing the projection of groundwater extraction. A limited dataset, literature values, field surveys, and the ‘crop water-requirement method’ are combined to determine boundary conditions, aquifer parameters, and sources and sinks. The model results show good agreement between predicted and observed values; groundwater-level contours agree with the conceptual model and expected flow direction, and, in terms of water balance, flow volumes are in accordance with literature values. Average annual water consumption for irrigation is estimated to be 29 million m3 and simulation results show that a reduction of groundwater pumping by 40% could recover groundwater heads, reducing the water taken from storage. This study presents an example of how to develop a local numerical groundwater model to support management strategies under the condition of data scarcity.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号