共查询到20条相似文献，搜索用时 15 毫秒
1.
Angus I. Best Lucy M. MacGregor Jeremy Sothcott Tim A. Minshull 《Geophysical Prospecting》2011,59(4):777-786
Improvements in the joint inversion of seismic and marine controlled source electromagnetic data sets will require better constrained models of the joint elastic‐electrical properties of reservoir rocks. Various effective medium models were compared to a novel laboratory data set of elastic velocity and electrical resistivity (obtained on 67 reservoir sandstone samples saturated with 35 g/l brine at a differential pressure of 8 MPa) with mixed results. Hence, we developed a new three‐phase effective medium model for sandstones with pore‐filling clay minerals based on the combined self‐consistent approximation and differential effective medium model. We found that using a critical porosity of 0.5 and an aspect ratio of 1 for all three components, the proposed model gave accurate model predictions of the observed magnitudes of P‐wave velocity and electrical resistivity and of the divergent trends of clean and clay‐rich sandstones at higher porosities. Using only a few well‐constrained input parameters, the new model offers a practical way to predict in situ porosity and clay content in brine saturated sandstones from co‐located P‐wave velocity and electrical resistivity data sets. 相似文献
2.
Computer simulations are used to calculate the elastic properties of model cemented sandstones composed of two or more mineral phases. Two idealized models are considered – a grain‐overlap clay/quartz mix and a pore‐lining clay/quartz mix. Unlike experimental data, the numerical data exhibit little noise yet cover a wide range of quartz/cement ratios and porosities. The results of the computations are in good agreement with experimental data for clay‐bearing consolidated sandstones. The effective modulus of solid mineral mixtures is found to be relatively insensitive to microstructural detail. It is shown that the Hashin–Shtrikman average is a good estimate for the modulus of the solid mineral mixtures. The distribution of the cement phase is found to have little effect on the computed modulus–porosity relationships. Numerical data for dry and saturated states confirm that Gassmann's equations remain valid for porous materials composed of multiple solid constituents. As noted previously, the Krief relationship successfully describes the porosity dependence of the dry shear modulus, and a recent empirical relationship provides a good estimate for the dry‐rock Poisson's ratio. From the numerical computations, a new empirical model, which requires only a knowledge of system mineralogy, is proposed for the modulus–porosity relationship of isotropic dry or fluid‐saturated porous materials composed of multiple solid constituents. Comparisons with experimental data for clean and shaly sandstones and computations for more complex, three‐mineral (quartz/dolomite/clay) systems show good agreement with the proposed model over a very wide range of porosities. 相似文献
3.
Compressional- and shear-wave velocities as a function of confining stress in dry sandstones 总被引：3，自引：0，他引：3
A laboratory study was carried out to investigate the influence of confining stress on compressional- and shear-wave velocities for a set of rock samples from gas-producing sandstone reservoirs in the Cooper Basin, South Australia. The suite of samples consists of 22 consolidated sublitharenites with helium porosity ranging from 2.6% to 16.6%. We used a pulse-echo technique to measure compressional- and shear-wave velocities on dry samples (cylindrical 4.6 × 2 cm) at room temperature and at elevated confining stress (≤ 60 MPa). Compressional- and shear-wave velocities in samples increase non-linearly with confining stress. A regression equation of the form V = A ? Be?DP gives a good fit to the measured velocities with improved prediction of velocities at high confining stresses compared with equations suggested by other studies. The predicted microcrack-closure stresses of the samples show values ranging from 70 MPa to 95 MPa and insignificant correlation with porosity, permeability or clay content. There is a positive correlation between change in velocity with core porosity and permeability, but this association is weak and diminishes with increasing confining stress. Experimental results show that pore geometry, grain-contact type, and distribution and location of clay particles may be more significant than total porosity and clay content in describing the stress sensitivity of sandstones at in situ reservoir effective stress. The stress dependence of Cooper Basin sandstones is very large compared with data from other studies. The implication of our study for hydrocarbon exploration is that where the in situ reservoir effective stress is much less than the microcrack-closure stress of the reservoir rocks, the variation of reservoir effective stress could cause significant changes in velocity of the reservoir rocks. The velocity changes induced by effective stress in highly stress-sensitive rocks can be detected at sonic-log and probably surface-seismic frequencies. 相似文献
4.
Colin M. Sayers 《Geophysical Prospecting》2002,50(4):393-401
Azimuthal anisotropy in rocks can result from the presence of one or more sets of partially aligned fractures with orientations determined by the stress history of the rock. A shear wave propagating in an azimuthally anisotropic medium splits into two components with different polarizations if the source polarization is not aligned with the principal axes of the medium. For vertical propagation of shear waves in a horizontally layered medium containing vertical fractures, the shear‐wave splitting depends on the shear compliance of the fractures, but is independent of their normal compliance. If the fractures are not perfectly vertical, the shear‐wave splitting also depends on the normal compliance of the fractures. The normal compliance of a fluid‐filled fracture decreases with increasing fluid bulk modulus. For dipping fractures, this results in a decrease in shear‐wave splitting and an increase in shear‐wave velocity with increasing fluid bulk modulus. The sensitivity of the shear‐wave splitting to fluid bulk modulus depends on the interconnectivity of the fracture network, the permeability of the background medium and on whether the fracture is fully or partially saturated. 相似文献
5.
We design a velocity–porosity model for sand-shale environments with the emphasis on its application to petrophysical interpretation of compressional and shear velocities. In order to achieve this objective, we extend the velocity–porosity model proposed by Krief et al., to account for the effect of clay content in sandstones, using the published laboratory experiments on rocks and well log data in a wide range of porosities and clay contents. The model of Krief et al. works well for clean compacted rocks. It assumes that compressional and shear velocities in a porous fluid-saturated rock obey Gassmann formulae with the Biot compliance coefficient. In order to use this model for clay-rich rocks, we assume that the bulk and shear moduli of the grain material, and the dependence of the compliance on porosity, are functions of the clay content. Statistical analysis of published laboratory data shows that the moduli of the matrix grain material are best defined by low Hashin–Shtrikman bounds. The parameters of the model include the bulk and shear moduli of the sand and clay mineral components as well as coefficients which define the dependence of the bulk and shear compliance on porosity and clay content. The constants of the model are determined by a multivariate non-linear regression fit for P- and S-velocities as functions of porosity and clay content using the data acquired in the area of interest. In order to demonstrate the potential application of the proposed model to petrophysical interpretation, we design an inversion procedure, which allows us to estimate porosity, saturation and/or clay content from compressional and shear velocities. Testing of the model on laboratory data and a set of well logs from Carnarvon Basin, Australia, shows good agreement between predictions and measurements. This simple velocity-porosity-clay semi-empirical model could be used for more reliable petrophysical interpretation of compressional and shear velocities obtained from well logs or surface seismic data. 相似文献
6.
We measured in the laboratory ultrasonic compressional and shear‐wave velocity and attenuation (0.7–1.0 MHz) and low‐frequency (2 Hz) electrical resistivity on 63 sandstone samples with a wide range of petrophysical properties to study the influence of reservoir porosity, permeability and clay content on the joint elastic‐electrical properties of reservoir sandstones. P‐ and S‐wave velocities were found to be linearly correlated with apparent electrical formation factor on a semi‐logarithmic scale for both clean and clay‐rich sandstones; P‐ and S‐wave attenuations showed a bell‐shaped correlation (partial for S‐waves) with apparent electrical formation factor. The joint elastic‐electrical properties provide a way to discriminate between sandstones with similar porosities but with different clay contents. The laboratory results can be used to estimate sandstone reservoir permeability from seismic velocity and apparent formation factor obtained from co‐located seismic and controlled source electromagnetic surveys. 相似文献
7.
We conducted a laboratory study of the joint elastic‐electrical properties of sixty‐three brine‐saturated sandstone samples to assess the likely impact of differential pressure (confining minus pore fluid pressures) in the range 8–60 MPa on the joint interpretation of marine seismic and controlled‐source electromagnetic survey data. The samples showed a wide range of petrophysical properties representative of most sandstone reservoirs. We found that a regression equation comprising both a constant and an exponential part gave a good fit to the pressure dependence of all five measured geophysical parameters (ultrasonic P‐ and S‐wave velocity, attenuation and electrical resistivity). Electrical resistivity was more pressure‐sensitive in clay‐rich sandstones with higher concentrations of low aspect ratio pores and micropores than in clean sandstones. Attenuation was more pressure‐sensitive in clean sandstones with large open pores (macropores) than in clay‐rich sandstones. Pore shape did not show any influence on the pressure sensitivity of elastic velocity. As differential pressure increases, the effect of the low aspect ratio pores and micropores on electrical resistivity becomes stronger than the effect of the macropores on attenuation. Further analysis of correlations among the five parameters as a function of pressure revealed potentially diagnostic relationships for geopressure prediction in reservoir sandstones. 相似文献
8.
Ultrasonic compressional‐ and shear‐wave velocities have been measured on 34 samples of sandstones from hydrocarbon reservoirs. The sandstones are all of low clay content, high porosity, and cover a wide range of permeabilities. They were measured dry and brine‐saturated under hydrostatic effective stresses of 10, 20 and 40 MPa. For eight of the sandstones, ultrasonic velocity measurements were made at different partial water saturations in the range from dry to fully saturated. The Gassmann–Biot theory is found to account for most of the changes in velocities at high effective stress levels when the dry sandstones are fully saturated with brine, provided the lower velocities resulting when the dry sandstone initially adsorbs small amounts of moisture are used to determine the elastic properties of the ‘dry’ sandstone. At lower effective stress levels, local flow phenomena due to the presence of open microcracks are assumed to be responsible for measured velocities higher than those predicted by the theory. The partial saturation results are modelled fairly closely by the Gassmann–Biot theory, assuming heterogeneous saturation for P‐waves. 相似文献
9.
利用室内SDT-20动三轴试验机对贵阳原状红黏土进行循环荷载作用下动力特性试验,探究不同围压、固结应力比和振动频率对红黏土动力学参数的影响,结合实验数据及参数模型拟合贵阳红黏土动应力应变关系、动弹性模量及阻尼比经验公式,结果表明：贵阳红黏土动本构关系仍符合H-D双曲线增长模型,动弹性模量随动应变增长非线性衰减,阻尼比随动应变增长非线性增加。围压及固结应力比对红黏土动力学参数具有显著影响,围压及固结应力比增大,动变形减小,动弹性模量增加,阻尼比降低,同等条件下,提高振动频率,动力学参数显示出与围压及固结应力比相同规律,但不显著。基于H-D模型,给出了贵阳原状红黏土双曲线模型参数,通过多元回归分析,拟合并提出针对贵阳红黏土的在不同试验条件下动弹性模量衰减及阻尼比经验公式,给出相应的拟合参数。 相似文献
10.
Osman Uyanık 《Journal of Applied Geophysics》2011,73(1):16-24
This study devises a new analytical relationship to determine the porosity of water-saturated soils at shallow depth using seismic compressional and shear wave velocities. Seismic refraction surveys together with soil sample collection were performed in selected areas containing water-saturated clay–silt, sand and gravely soils. Classification of clay–silt, sand and gravel dense soils provided the coefficient of experimental equation between the data sets, namely, Poisson's ratio, shear modulus and porosity values. This study presents a new analytical relationship between Poisson's ratio and shear modulus values, which are obtained from seismic velocities and porosity values of water-saturated material computed from water content and grain densities, which are determined by laboratory analysis of disturbed samples. The analytical relationship between data sets indicates that when the shear modulus of water-saturated loose soil increases, porosity decreases logarithmically. If shear modulus increases in dense or solid saturated soils, porosity decreases linearly. 相似文献
11.
The shape and location of clay within sandstones have a large impact on the P‐wave and S‐wave velocities of the rock. They also have a large effect on reservoir properties and the interpretation of those properties from seismic data and well logs. Numerical models of different distributions of clay – structural, laminar and dispersed clay – can lead to an understanding of these effects. Clay which is located between quartz grains, structural clay, will reduce the P‐wave and S‐wave velocities of the rock. If the clay particles become aligned or form layers, the velocities perpendicular to the alignment will be reduced further. S‐wave velocities decrease more rapidly than P‐wave velocities with increasing clay content, and therefore Poisson's ratios will increase as the velocities decrease. These effects are more pronounced for compacted sandstones. Small amounts of clay that are located in the pore space will have little effect on the P‐wave velocity due to the competing influence of the density effect and pore‐fluid stiffening. The S‐wave velocity will decrease due to the density effect and thus the Poisson's ratio will increase. When there is sufficient clay to bridge the gaps between the quartz grains, P‐wave and S‐wave velocities rise rapidly and the Poisson's ratios decrease. These effects are more pronounced for under‐compacted sandstones. These general results are only slightly modified when the intrinsic anisotropy of the clay material is taken into account. Numerical models indicate that there is a strong, nearly linear relationship between P‐wave and S‐wave velocity which is almost independent of clay distribution. S‐wave velocities can be predicted reasonably accurately from P‐wave velocities based on empirical relationships. However, this does not provide any connection between the elastic and petrophysical properties of the rocks. Numerical modelling offers this connection but requires the inclusion of clay distribution and anisotropy to provide a model that is consistent with both the elastic and petrophysical properties. If clay distribution is ignored, predicting porosities from P‐wave or S‐wave data, for example, can result in large errors. Estimation of the clay distribution from P‐wave and S‐wave velocities requires good estimates of the porosity and clay volume and verification from petrographic analyses of core or cuttings. For a real data example, numerical models of the elastic properties suggest the predominance of dispersed clay in a fluvial sand from matching P‐wave and S‐wave velocity well log data using log‐based estimates of the clay volume and porosity. This is consistent with an interpretation of other log data. 相似文献
12.
Wave velocities and attenuation of shaley sandstones as a function of pore pressure and partial saturation 总被引：3，自引：0，他引：3
Nam H. Pham † José M. Carcione Hans B. Helle Bjørn Ursin 《Geophysical Prospecting》2002,50(6):615-627
We obtain the wave velocities and quality factors of clay‐bearing sandstones as a function of pore pressure, frequency and partial saturation. The model is based on a Biot‐type three‐phase theory that considers the coexistence of two solids (sand grains and clay particles) and a fluid mixture. Additional attenuation is described with the constant‐Q model and viscodynamic functions to model the high‐frequency behaviour. We apply a uniform gas/fluid mixing law that satisfies the Wood and Voigt averages at low and high frequencies, respectively. Pressure effects are accounted for by using an effective stress law. By fitting a permeability model of the Kozeny– Carman type to core data, the model is able to predict wave velocity and attenuation from seismic to ultrasonic frequencies, including the effects of partial saturation. Testing of the model with laboratory data shows good agreement between predictions and measurements. 相似文献
13.
In-Chang Ryu 《Island Arc》2003,12(4):398-410
Abstract Sandstone petrography considered within a sequence stratigraphic framework provides a better understanding of the characteristics of the Eocene Tyee Basin, an accretionary and forearc sequence, southern Oregon Coast Range. Detailed comparison of the relative abundance of major framework grains documents a marked difference in the sandstone composition of each depositional sequence. Such a difference is mainly due to an abrupt change in provenance, from a local Klamath Mountains metasedimentary source to a more distant extrabasinal Idaho Batholith‐Clarno volcanic arc source. Furthermore, the composition of framework grains varies systematically from the lowstand systems tract to the highstand systems tract within a depositional sequence. This suggests that relative sea level change in the depositional basin, and tectonics in the source area, can affect the patterns of sedimentation and sandstone composition. In addition, the Eocene Tyee Basin sandstones have a down‐section distribution of authigenic minerals, consisting of early formed zeolites and late‐stage quartz, as well as a change in the abundance of smectite to mixed‐layer chlorite/smectite with increasing burial depth. The down‐section distribution of authigenic minerals is also causally linked to the compositional variation of framework grains in each depositional sequence with increasing burial temperature. Much primary porosity has been filled with these authigenic minerals, which diminishes the permeability of potential reservoir rocks. Reservoir‐quality porosities and permeabilities, however, are present locally in the basin. The development of these reservoir‐quality sandstones within the Eocene Tyee Basin sequence is due to a complex burial diagenesis, which is directly related to temporal and spatial variations in original detrital mineralogy, in sedimentation pattern, and in burial temperature in the basin. 相似文献
14.
We obtain the wave velocities of clay-bearing sandstones as a function of clay content, porosity and frequency. Unlike previous theories, based simply on slowness and/or moduli averaging or two-phase models, we use a Biot-type three-phase theory that considers the existence of two solids (sand grains and clay particles) and a fluid. The theory, which is consistent with the critical porosity concept, uses three free parameters that determine the dependence of the dry-rock moduli of the sand and clay matrices as a function of porosity and clay content.
Testing of the model with laboratory data shows good agreement between predictions and measurements. In addition to a rock physics model that can be useful for petrophysical interpretation of wave velocities obtained from well logs and surface seismic data, the model provides the differential equation for computing synthetic seismograms in inhomogeneous media, from the seismic to the ultrasonic frequency bands. 相似文献
Testing of the model with laboratory data shows good agreement between predictions and measurements. In addition to a rock physics model that can be useful for petrophysical interpretation of wave velocities obtained from well logs and surface seismic data, the model provides the differential equation for computing synthetic seismograms in inhomogeneous media, from the seismic to the ultrasonic frequency bands. 相似文献
15.
Ismael Himar Falcon-Suarez Kelvin Amalokwu Jordi Delgado-Martin Ben Callow Katleen Robert Laurence North Sourav K. Sahoo Angus I. Best 《Geophysical Prospecting》2019,67(4):784-803
Synthetic rock samples can offer advantages over natural rock samples when used for laboratory rock physical properties studies, provided their success as natural analogues is well understood. The ability of synthetic rocks to mimic the natural stress dependency of elastic wave, electrical and fluid transport properties is of primary interest. Hence, we compare a consistent set of laboratory multi-physics measurements obtained on four quartz sandstone samples (porosity range 20–25%) comprising two synthetic and two natural (Berea and Corvio) samples, the latter used extensively as standards in rock physics research. We measured simultaneously ultrasonic (P- and S-wave) velocity and attenuation, electrical resistivity, permeability and axial and radial strains over a wide range of differential pressure (confining stress 15–50 MPa; pore pressure 5–10 MPa) on the four brine saturated samples. Despite some obvious physical discrepancies caused by the synthetic manufacturing process, such as silica cementation and anisotropy, the results show only small differences in stress dependency between the synthetic and natural sandstones for all measured parameters. Stress dependency analysis of the dry samples using an isotropic effective medium model of spheroidal pores and penny-shaped cracks, together with a granular cohesion model, provide evidence of crack closure mechanisms in the natural sandstones, seen to a much lesser extent in the synthetic sandstones. The smaller grain size, greater cement content, and cementation under oedometric conditions particularly affect the fluid transport properties of the synthetic sandstones, resulting in lower permeability and higher electrical resistivity for a similar porosity. The effective stress coefficients, determined for each parameter, are in agreement with data reported in the literature. Our results for the particular synthetic materials that were tested suggest that synthetic sandstones can serve as good proxies for natural sandstones for studies of elastic and mechanical properties, but should be used with care for transport properties studies. 相似文献
16.
We develop a semi‐empirical model which combines the theoretical model of Xu and White and the empirical formula of Han, Nur and Morgan in sand–clay environments. This new model may be used for petrophysical interpretation of P‐ and S‐wave velocities. In particular, we are able to obtain an independent estimation of aspect ratios based on log data and seismic velocity, and also the relationship between velocities and other reservoir parameters (e.g. porosity and clay content), thus providing a prediction of shear‐wave velocity. To achieve this, we first use Kuster and Toksöz's theory to derive bulk and shear moduli in a sand–clay mixture. Secondly, Xu and White's model is combined with an artificial neural network to invert the depth‐dependent variation of pore aspect ratios. Finally these aspect ratio results are linked to the empirical formula of Han, Nur and Morgan, using a multiple regression algorithm for petrophysical interpretation. Tests on field data from a North Sea reservoir show that this semi‐empirical model provides simple but satisfactory results for the prediction of shear‐wave velocities and the estimation of reservoir parameters. 相似文献
17.
Subgrade soils of traffic infrastructures are subjected to large numbers of load applications at a stress level below their shear strength. It is therefore of great practical relevance to study the deformation behavior of soft clay under long-term cyclic loading. In this study, a series of monotonic triaxial tests and long-term cyclic (50,000 cycles) triaxial tests have been carried out to investigate the undrained deformation behavior of undisturbed soft clay from Wenzhou, China. The stress–strain hysteretic loop, resilient modulus and permanent strain of the tested samples were found significantly dependent on CSR and confining pressure. With an increase of CSR and confining pressure, the resilient modulus decreases more significantly with increasing number of cycles and the accumulation rate of permanent strain increases. Furthermore, the shape of the stress–strain hysteretic loop almost remains unchanged and the resilient modulus tends to a steady value after a large number of cycles. Based on the experimental results, two equations are established for the prediction of long-term resilient modulus and permanent strain. Finally, a new critical value of 0.65 is suggested for CSR. When CSR>0.65, the resilient modulus for large number of cycles is reduced to a so called “asymptotic stiffness” and the accumulation rate of permanent strain significantly increases. 相似文献
18.
Clays and clay‐bearing rocks like shale are extremely water sensitive. This is partly due to the interaction between water and mineral surfaces, strengthened by the presence of nanometer‐size pores and related large specific surface areas. Molecular‐scale numerical simulations, using a discrete‐element model, show that shear rigidity can be associated with structurally ordered (bound or adsorbed) water near charged surfaces. Building on these and other molecular dynamics simulations plus nanoscale experiments from the literature, the water monolayer adjacent to hydrophilic solid surfaces appears to be characterised by shear stiffness and/or enhanced viscosity. In both cases, elastic wave propagation will be affected by the bound or adsorbed water. Using a simple rock physics model, bound water properties were adjusted to match laboratory measured P‐ and S‐wave velocities on pure water‐saturated kaolinite and smectite. To fit the measured stress sensitivity, particularly for kaolinite, the contribution from solid‐grain contact stiffness needs to be added. The model predicts, particularly for S‐waves, that viscoelastic bound water could be a source of dispersion in clay and clay‐rich rocks. The bound‐water‐based rock physics model is found to represent a lower bound to laboratory‐measured velocities obtained with shales of different mineralogy and porosity levels. 相似文献
19.
Strength and deformation behavior of the Shimanto accretionary complex across the Nobeoka thrust 
下载免费PDF全文
下载免费PDF全文 A rapid reduction in sediment porosity from 60 to 70 % at seafloor to less than 10 % at several kilometers depth can play an important role in deformation and seismicity in the shallow portion of subduction zones. We conducted deformation experiments on rocks from an ancient accretionary complex, the Shimanto Belt, across the Nobeoka Thrust to understand the deformation behaviors of rocks along plate boundary faults at seismogenic depth. Our experimental results for phyllites in the hanging wall and shale‐tuff mélanges in the footwall of the Nobeoka Thrust indicate that the Shimanto Belt rocks fail brittlely accompanied by a stress drop at effective pressures < 80 MPa, whereas they exhibit strain hardening at higher effective pressures. The transition from brittle to ductile behavior in the shale–tuff mélanges lies on the same trend in effective stress–porosity space as that for clay‐rich and tuffaceous sediments subducting into the modern Nankai subduction zone. Both the absolute yield strength and the effective pressure at the brittle–ductile transition for the phyllosilicate‐rich materials are much lower than for sandstones. These results suggest that as the clay‐rich or tuffaceous sediments subduct and their porosities are reduced, their deformation behavior gradually transitions from ductile to brittle and their yield strength increases. Our results also suggest that samples of the ancient Shimanto accretionary prism can serve as an analog for underthrust rocks at seismogenic depth in the modern Nankai Trough. 相似文献
20.
本文基于Biot理论,推导出Zoeppritz形式的双相介质分界面上弹性波的反射与透射公式,对单相Zoeppritz公式与双相反射系数公式进行了比较,对双相介质含油、水、气不同流体时的反射规律以及孔隙度、渗透率、饱和度等储层参数对纵波反射的影响进行了研究.数值模拟分析表明,双相与单相反射公式的主要差异在于双相介质反射公式中考虑了液相、固液耦合相弹性模量的影响;油砂、水砂、气砂岩的慢P波反射差异明显;快P波反射对孔隙度的变化敏感,饱和度次之,对渗透率和频率的变化不敏感. 相似文献