首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
In natural waters,exopolymers or extracellular polymeric substances(EPS) exuded by microorganisms interact with clay particles,resulting in the flocculation of clays and hence alteration to the properties of suspended cohesive sediments.To investigate and further understand how neutral EPS affect cohesive sediment transport and the final sediment yield,an experimental study was conducted on laboratory-prepared clay and guar gum(used as an analog for neutral EPS) suspensions to characterize EPS-induced flocculation and the settling velocity of resultant floes.Four different clays consisting of kaolinite,illite,Ca-montmorillonite,and Na-montmorillonite were studied to examine the influence of different layer charges on clay flocculation induced by neutral EPS.Floc size was determined by a laser particle size analyzer,and settling velocity estimated by analyzing the time-series floc settling images captured by an optical microscope.Results indicate that neutral EPS promote clay-EPS flocculation for all four clays with the particle/floc size significantly increased from～0.1-60μm to as large as～600μm.Clays’ layer charge has a profound influence on the clay-EPS flocculation.With the same floc size,the settling velocity of clay-EPS flocs is typically smaller than that of pure clay flocs,which is attributed to the reduced density of flocs caused by the EPS. However,for flocs of the same composition(e.g.pure clay or hybrid clay-EPS mixture),the settling velocity increases with size.The fractal dimension of these clay-EPS flocs estimated from settling velocity ranges from 1.39 to 1.47,which are smaller than that of pure clay flocs,indicating that these flocs are less compacted than the pure clay flocs.  相似文献   

2.
Multimodal particle size distributions (PSDs) of fine-grained cohesive sediments are common in marine and coastal environments. The curve-fitting software in this study decomposed such multimodal PSDs into subordinate log-normal PSDs. Four modal peaks, consisting of four-level ordered structures of primary particles, flocculi, microflocs, and macroflocs, were identified and found to alternately rise and sink in a flow-varying tidal cycle due to shear-dependent flocculation. The four modal PSD could be simplified further into two discrete size groups of flocculi and flocs. This allowed the development of a two-class population balance equation (TCPBE) model with flocculi and flocs to simulate flocculation involving multimodal PSDs. The one-dimensional vertical (1-DV) TCPBE model further incorporated the Navier-Stokes equation with the k-ε turbulence closure and the sediment mass balance equations. Multimodal flocculation as well as turbulent flow and sediment transport in a flow-varying tidal cycle could be simulated well using the proposed model. The 1-DV TCPBE was concluded to be the simplest model that is capable of simulating multimodal flocculation in the turbulent flow field of marine and coastal zones.  相似文献   

3.
A depth-averaged 2-D numerical model for unsteady flow, salinity and cohesive sediment transport in estuaries is established using the finite volume method on the non-staggered, curvilinear grid. The convection terms are discretized by upwind schemes, the diffusion terms are by the central difference scheme, and the time derivative terms are by the three-time-level implicit scheme. The coupling of flow velocity and water level in the 2-D shallow water equations is achieved by the SIMPLEC algorithm with the Rhie and Chow's momentum interpolation method. The sediment model calculates the settling, deposition, erosion and transport of cohesive sediment, taking into account the influence of sediment size, sediment concentration, salinity and turbulence intensity on the flocculation of cohesive sediment. The flow model is first tested against the measurement data in the Tokyo Bay and San Francisco Bay, showing good agreements. And then, the entire model of flow, salinity and sediment transport is verified in the Gironde Estuary. The water elevation, flow velocity, salinity and sediment concentration are well predicted.  相似文献   

4.
The purpose of this paper is to establish a relation between a few measurable quantities (the so-called ζ potential, organic matter content, and shear rate) and the flocculation behavior of mud. The results obtained with small-scale flocculation experiments (mixing jar) are compared to results of large-scale experiments (settling column). The mud used for all experiments has been collected in October 2007 in the lower Western Schelde, near Antwerp, Belgium. From this study, it was found that the mean floc size and the Kolmogorov microscale vary in a similar way with the shear rate for suspensions with different pH and salt concentrations. The size of flocs at a given shear rate depends on the properties of the suspension, which affect the electrokinetic properties of the sediment; these can be described by means of the ζ potential. The main findings of this paper are: (1) In saline suspensions at pH = 8, the mean floc size increases when the salt concentration and the ζ potential increase. (2) For a given ζ potential, the mean floc size at low pH is larger than observed at pH = 8 for any added salt. (3) The mean floc size increases with increasing organic matter content. (4) Mud with no organic matter at pH = 8 and no added salt flocculates very little. The response of mud suspensions to variations in salinity and pH is similar to that of kaolinite. This suggests that a general trend can be established for different and complex types of clays and mud. This systematic study can therefore be used for further development of flocculation models.  相似文献   

5.
The transport of fine-grained particles in estuarine and coastal waters is influenced by flocculation processes (aggregation and floc breakup). As a consequence, the particle size varies with time in the water column, and can be orders of magnitude larger than those of primary particles. In this study the variations in floc size is simulated using a size-resolved method, which approximates the real size distribution of particles by a range of size bins and solves a mass balance equation for each bin. To predict the size distribution both aggregation and breakup processes are included. The conventional rectilinear aggregation kernel is used which considers both turbulent shear and differential settling. The breakup kernel accounts for the fractal dimension of the flocs. A flocculation simulation is compared to the settling column lab experiments of Winterwerp [1998. A simple model for turbulence induced flocculation of cohesive sediment, Journal of Hydraulic Research, 36, 309–326], and a one-dimensional sediment transport model is verified with the observed variations in floc size and concentration over tidal cycles in a laboratory flume experiment of Bale et al. [2002. Direct observation of the formation and break-up of aggregates in an annular flume using laser reflectance particle sizing. In: Winterwerp, J.C., Kranenburg, C. (Eds.), Fine Sediment Dynamics in the Marine Environment. Elsevier, pp. 189–201]. The numerical simulations compare qualitatively and quantitatively well with the laboratory measurements, and the analysis of the two simulation results indicates that the median floc size can be correlated to the sediment concentration and Kolmogorov microscale. Sensitivity studies are conducted to explore the role of settling velocity and erosion rate. The results are not sensitive towards the formulation of settling velocity, but the parameterization of erosion flux is important. The studies show that for predicting the sediment deposition flux it is crucial to include flocculation processes.  相似文献   

6.
The saltation regime is very important for understanding the sediment transport mechanism. However,there is no consensus on a model for the saltation regime. This study answers several questions raised with respect to the Eulerian-Lagrangian modeling of sediment transport. The first question is why the previous saltation models that use different combinations of hydrodynamic forces yielded acceptable results? The second question is which shear lift model(i.e. a shear lift expression and its coefficient) is more appropriate? Another important question is which hydrodynamic forces have greater contributions to the saltation characteristics of a sediment particle? The last question is what are the contributions of the turbulence fluctuations as well as effects of using two-and three-dimensional(2 D and 3 D) models on the simulation results? In order to fairly answer these questions, a systematic study was done by considering different scenarios. The current study is the first attempt to clearly discuss these issues. A comprehensive 3 D saltation model for non-cohesive sediment was developed that includes all the hydrodynamic forces acting on the particle. The random nature of sediment transport was included using turbulent flow and bed-particle collision models. The eddy interaction model was applied to generate a3 D turbulent flow field. Bed-particle collisions were considered using the concept of a contact zone and a corresponding contact point. The validation of the model was done using the available experimental data for a wide range of sediment size(0.03 to 4.8 cm). For the first question, the results indicated that some of the hydrodynamic effects show opposing trends and some have negligible effects. With these opposing effects it is possible to adjust the coefficients of different models to achieve acceptable agreement with the same experimental data while omitting some aspects of the physics of the process. A suitable model for the shear lift force was developed by linking the lift coefficient to the drag coefficient and the contributions of the hydrodynamic forces and turbulence fluctuations as well as the consequences of using of 2 D and 3 D models were studied. The results indicate that the shear lift force and turbulent flow fluctuations are important factors for the saltation of both sand and gravel, and they cannot be ignored.  相似文献   

7.
Both the floc formation and floc breakup of cohesive sediment are affected by turbulent shear which is recognized as one of the most important parameters, and thus, on the settling and transport of cohesive sediment. In this study, the development of floc characteristics at early stage and steady-state of flocculation were investigated via a three-dimensional lattice Boltzmann numerical model for turbulence-induced flocculation. Simulations for collision and aggregation of various size particles, floc growth, and breakup in isotropic and homogenous turbulent flows with different shear stresses were conducted. Model results for the temporal evolution of floc size distribution show that the normalized floc size distributions is time-independent during early stage of flocculation, and at steady-state, shear rate has no effect on the shape of normalized floc size distribution. Furthermore, the size, settling velocity, and effective density of flocs at the non-equilibrium flocculation stage do not change significantly for shear stresses in the range 0–0.4 N m?2. The relationships between floc size and settling velocity established during floc growth stages and that during steady-states are different.  相似文献   

8.
Research over the last decade has shown that the suspended sediment loads of many rivers are dominated by composite particles. These particles are also known as aggregates or flocs, and are commonly made up of constituent mineral particles, which evidence a wide range of grain sizes, and organic matter. The resulting in situ or effective particle size characteristics of fluvial suspended sediment exert a major control on all processes of entrainment, transport and deposition. The significance of composite suspended sediment particles in glacial meltwater streams has, however, not been established. Existing data on the particle size characteristics of suspended sediment in glacial meltwaters relate to the dispersed mineral fraction (absolute particle size), which, for certain size fractions, may bear little relationship to the effective or in situ distribution. Existing understanding of composite particle formation within freshwater environments would suggest that in‐stream flocculation processes do not take place in glacial meltwater systems because of the absence of organic binding agents. However, we report preliminary scanning electron microscopy data for one Alpine and two Himalayan glaciers that show composite particles are present in the suspended sediment load of the meltwater system. The genesis and structure of these composite particles and their constituent grain size characteristics are discussed. We present evidence for the existence of both aggregates, or composite particles whose features are largely inherited from source materials, and flocs, which represent composite particles produced by in‐stream flocculation processes. In the absence of organic materials, the latter may result solely from electrochemical flocculation in the meltwater sediment system. This type of floc formation has not been reported previously in the freshwater fluvial environment. Further work is needed to test the wider significance of these data and to investigate the effective particle size characteristics of suspended sediment associated with high concentration outburst events. Such events make a major contribution to suspended sediment fluxes in meltwater streams and may provide conditions that are conducive to composite particle formation by flocculation. Copyright © 2002 John Wiley & Sons, Ltd.  相似文献   

9.
A 2D depth‐averaged hydrodynamic, sediment transport and bed morphology model named STREMR HySeD is presented. The depth‐averaged sediment transport equations are derived from the 3D dilute, multiphase, flow equations and are incorporated into the hydrodynamic model STREMR. The hydrodynamic model includes a two‐equation turbulence model and a correction for the mean flow due to secondary flows. The suspended sediment load can be subdivided into different size classes using the continuum (two‐fluid) approach; however, only one bed sediment size is used herein. The validation of the model is presented by comparing the suspended sediment transport module against experimental measurements and analytical solutions for the case of equilibrium sediment‐laden in a transition from a rigid bed to a porous bed where re‐suspension of sediment is prevented. On the other hand, the bed‐load sediment transport and bed evolution numerical results are compared against bed equilibrium experimental results for the case of a meander bend. A sensitivity analysis based on the correction for secondary flow on the mean flow including the effect of secondary flow on bed shear stresses direction as well as the downward acceleration effect due to gravity on transverse bed slopes is performed and discussed. In general, acceptable agreement is found when comparing the numerical results obtained with STREMR HySeD against experimental measurements and analytical solutions. Copyright © 2007 John Wiley & Sons, Ltd.  相似文献   

10.
The composition and grain size characteristics of sediment in estuarine and coastal environments provide important information on the material source, hydrodynamic environment, environmental events,etc. However, few studies have focused on the sediment characteristics of the entire Qiantang Estuary,particularly, on the correlation between hydrodynamics and sediment properties. Through systematic sampling of the surface sediment in a large area of the Qiantang Estuary, the spatial distribution ch...  相似文献   

11.
Numerous quantitative and qualitative variables control suspended sediment dynamics in karst systems. The objective of this study was to identify the hydrodynamic variables controlling the transport properties of particles in a karst aquifer (western Paris basin). The particle size distribution of suspended sediment infiltrating via a swallow hole was compared to that in discharge from a spring, allowing identification of the particle transport properties of the karst system. Hill and Smith analysis, a type of multivariate analysis that allows joint examination of quantitative and qualitative variables, was used to identify the hydrodynamic parameters controlling the transport properties of the suspended matter. The results demonstrate that the particle size distribution discharging at the karst spring is controlled by spring discharge and the hydraulic gradient of the system. The hydraulic gradient is defined by the piezometric level and the stage of the Seine River, which is in turn controlled by the tide. This study illustrates the use of Hill and Smith analysis to identify those variables which control suspended sediment transport. It also illustrates the application of this analysis to identify boundary conditions and evaluate variables which control the behaviour of the hydrologic system. Copyright © 2007 John Wiley & Sons, Ltd.  相似文献   

12.
The use of surfactant solutions for the in situ recovery of residual NAPL in aquifers is increasingly considered as a viable remediation technique. The injection of a few pore volumes of high concentration surfactant solutions can mobilize most of the residual NAPL contacted by the solutions. However, the washing solutions'physico-chemical properties (low density and high viscosity), combined with the natural porous media heterogeneity, can prevent a good sweep of the entire contaminated volume. From the petroleum industry, it is well-known that polymer solutions can be injected following a surfactant solution slug to act as a mobility buffer and increase the overall sweep efficiency. The objective of our laboratory study is first to select and characterize polymers that would be suitable for aquifer restoration. Our experiments showed that among several polymers, xanthan gum solution rheology was made in order to predict shear rates, xanthan gum concentrations, salinity, and temperature effects on solution viscosity. The second set of experiments were made with a sand box which was designed to reproduce a simple heterogeneous media consisting of layers of sand with different permeability. These tests illustrate the xanthan gum solution's ability to increase surfactant solution's sweep efficiency and limit viscous fingering. The tests established that: (1) the injection of xanthan solution behind a surfactant solution slug decreases fluid velocity in high permeability layers and increases it in low-permeability ones, thus increasing the sweep efficiency (2) xanthan solutions eliminate viscous fingering at the polymer/surfactant solution front; (3) a xanthan solution preflush is desirable to limit surfactant solution mobility and prevent surfactant adsorption on solids; and (4) depending on site heterogeneity injection strategies should be applied to limit overriding by low-density surfactant solution.  相似文献   

13.
Deposition and storage of fine‐grained (<62·5 μm) sediment in the hyporheic zone of gravel bed rivers frequently represents an important cause of aquatic habitat degradation. The particle size characteristics of such fine‐grained bed sediment (FGBS) exert an important control on its hydrodynamic properties and environmental impact. Traditionally, particle size analysis of FGBS in gravel bed rivers has focused on the absolute size distribution of the chemically dispersed mineral fraction. However, recent work has indicated that in common with fluvial suspended sediment, significant differences may exist between the absolute and the in situ, or effective, particle size composition of FGBS, as a result of the existence of aggregates, or composite particles. In the investigation reported in this paper, sealable bed traps that could be remotely opened to sample sediment deposited during specific storm runoff events and a laser back‐scatter probe were used to quantify the temporal and spatial variability of both the absolute and effective particle size composition of FGBS, and the associated suspended sediment from four gravel bed rivers in the Exe Basin, Devon, UK. The absolute particle size distributions of both the FGBS and suspended sediment evidenced c. >95%<62·5 μm sized primary particles and displayed a seasonal winter–summer fining, while the opposite trend was displayed by the effective particle size distribution of the FGBS and suspended sediment. The effective particle size distributions of both were typically highly aggregated, comprising up to 68%>62·5 μm sized particles. Spatial variation in the effective particle size and aggregation parameters was of secondary importance relative to temporal variation. The effective particle size distribution of the FGBS was consistently coarser and more aggregated than the associated suspended sediment and there was evidence of aggregate break‐up in samples of resuspended bed sediment. The implications of these findings for sediment transport modelling are considered. Copyright © 1999 John Wiley & Sons, Ltd.  相似文献   

14.
《Continental Shelf Research》2006,26(17-18):2299-2318
Since their development for investigating sand transport in the surf zone more than 25 years ago, optical backscatter sensors (OBSs) have been in continual use for a wide variety of scientific, engineering, and environmental-monitoring applications. Many OBS designs have evolved in that time but they all work in the same simple way. A water sample is illuminated by a light source and photodetectors in the sensor convert the light scattered from the sample to photocurrent. The amount of photocurrent depends mainly on the illuminated area of the particles, and because particle volume is proportional to area, the photocurrent provides an indirect estimate of suspended-sediment concentration. The relationship between OBS signal and sediment concentration is almost linear for many suspended sediments and this is the most important “good” feature for OBS users. Many other factors influence OBS measurements, including: (1) particle size, shape, composition, and aggregation/flocculation; (2) dissolved light-absorbing matter; (3) bubbles; and (4) chemical and biological fouling. Some of these factors can be troublesome and can result in poor data quality or ambiguous results; these are “bad” ones. And a few of the same factors can have truly “ugly” consequences when their effects are ignored. Unknown time variation in particle size or aggregation/flocculation and fouling will nearly always result in inaccurate OBSs data.  相似文献   

15.
Flocculation has an important impact on particle trapping in estuarine turbidity maximum (ETM) through associated increases in particle settling velocity. To quantify the importance of the flocculation processes, a size-resolved flocculation model is implemented into an ocean circulation model to simulate fine-grained particle trapping in an ETM. The model resolves the particle size from robust small flocs, about 30 μm, to very large flocs, over 1000 μm. An idealized two-dimensional model study is performed to simulate along-channel variations of suspended sediment concentrations driven by gravitational circulation and tidal currents. The results indicate that the flocculation processes play a key role in generating strong tidal asymmetrical variations in suspended sediment concentration and particle trapping. Comparison with observations suggests that the flocculation model produces realistic characteristics of an ETM.  相似文献   

16.
When fine particles are involved, cohesive properties of sediment can result in flocculation and significantly complicate sediment process studies. We combine data from field observations and state-of-the-art modeling to investigate and predict flocculation processes within a hypertidal estuary. The study site is the Welsh Channel located at the entrance of the Dee Estuary in Liverpool Bay. Field data consist of measurements from a fixed site deployment during 12–22 February 2008. Grain size, suspended sediment volume concentration, and current velocity were obtained hourly from moored instruments at 1.5 m above bed. Near-bottom water samples taken every hour from a research vessel are used to convert volume concentrations to mass concentrations for the moored measurements. We use the hydrodynamic model Proudman Oceanographic Laboratory Coastal Ocean Modelling System (POLCOMS) coupled with the turbulence model General Ocean Turbulence Model (GOTM) and a sediment module to obtain three-dimensional distributions of suspended particulate matter (SPM). Flocculation is identified by changes in grain size. Small flocs were found during flood and ebb periods—and correlate with strong currents—due to breakup, while coarse flocs were present during slack waters because of aggregation. A fractal number of 2.4 is found for the study site. Turbulent stresses and particle settling velocities are estimated and are found to be related via an exponential function. The result is a simple semiempirical formulation for the fall velocity of the particles solely depending on turbulent stresses. The formula is implemented in the full three-dimensional model to represent changes in particle size due to flocculation processes. Predictions from the model are in agreement with observations for both settling velocity and SPM. The SPM fortnight variability was reproduced by the model and the concentration peaks are almost in phase with those from field data.  相似文献   

17.
A large number of rivers are frozen annually, and the river ice cover has an influence on the geomorphological processes. These processes in cohesive sediment rivers are not fully understood. Therefore, this paper demonstrates the impact of river ice cover on sediment transport, i.e. turbidity, suspended sediment loads and erosion potential, compared with a river with ice‐free flow conditions. The present sediment transportation conditions during the annual cycle are analysed, and the implications of climate change on wintertime geomorphological processes are estimated. A one‐dimensional hydrodynamic model has been applied to the Kokemäenjoki River in Southwest Finland. The shear stress forces directed to the river bed are simulated with present and projected hydroclimatic conditions. The results of shear stress simulations indicate that a thermally formed smooth ice cover diminishes river bed erosion, compared with an ice‐free river with similar discharges. Based on long‐term field data, the river ice cover reduces turbidity statistically significantly. Furthermore, suspended sediment concentrations measured in ice‐free and ice‐covered river water reveal a diminishing effect of ice cover on riverine sediment load. The hydrodynamic simulations suggest that the influence of rippled ice cover on shear stress is varying. Climate change is projected to increase the winter discharges by 27–77% on average by 2070–2099. Thus, the increasing winter discharges and possible diminishing ice cover periods both increase the erosion potential of the river bed. Hence, the wintertime sediment load of the river is expected to become larger in the future. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

18.
Salinity difference between terrestrial river discharge and oceanic tidal water plays a role in modifying the local flow field and, as a consequence, estuarine morphodynamics. Although widely recognized, recent numerical studies exploring the long-term morphological evolution of river-influenced estuaries with two-dimensional, depth-averaged models have mostly neglected salinity. Using a three-dimensional morphodynamic model, we aim to gain more insight into the effect of salinity on the morphodynamics of fluvio-deltaic systems. Model results indicate that the resultant estuarine morphology established after 600 years differs remarkably when a salinity gradient is included. A fan-shaped river-mouth delta exhibits less seaward expansion and is cut through by narrower channels when salinity is included. The inclusion of salinity tends to generate estuarine circulation, which favours landward sediment transport and hence limits the growth of the delta while enhancing the development of intertidal areas. The formation of deltaic channel–shoal patterns resulting from morphodynamic evolution tends to strengthen salinity stratification, which is characterized by an increased gradient Richardson number. The direction of the depth-averaged residual sediment transport over a tide may be opposite to the direction of residual velocity, indicating the significant influence of baroclinic effects on the net sediment transport direction (and hence morphological change). The effect of salinity on morphological evolution becomes less profound when the strength of tidal or fluvial forcing is dominant over the other. The effects of sediment type and flocculation, which are particularly important when salinity gradients are present, are also discussed. Overall, this study highlights that neglecting salinity to simulate long-term estuarine morphodynamics requires more careful justification, particularly when the environment is characterized by fine sediment types (favouring suspended transport), and relatively large river discharge and estuarine depth (favouring baroclinic effects). © 2020 John Wiley & Sons, Ltd.  相似文献   

19.
《国际泥沙研究》2020,35(5):444-454
Turbidity is used as a surrogate for suspended sediment concentration (SSC), and as a regulatory tool for indicating land use disturbance and environmental protection. Turbidity relates linearly to suspended material, however, can show non-linear responses to particulate organic matter (POM), concomitant with changes in particle size distribution (PSD). In the paper the influence of ultra-fine particulate matter (UFPM) on specific turbidity and its association with POM in suspended sediment are shown for alpine rivers in the Southern Alps of New Zealand. The approach was two-fold: a field-based investigation of the relations between SSC, POM, and turbidity sampled during event flow; and experimental work on hydrodynamic particle size effects on SSC, POM, PSD, and turbidity. Specific turbidity changes over event flow and are sensitive to increasing proportional amounts of sand, UFPM, and POM in suspension. Furthermore, the UFPM is the size fraction (<6 μm) where POM increases. The implications of the current study are that the slopes of turbidity-SSC relations are undesirable in locations that may be dominated by cyclic release of POM or distinct pulses of fine-grained material. At locations where the turbidity-SSC slopes approximate 2, the POM proportion is usually <10% of the total suspended load. However, when turbidity-SSC slopes are <1 this is likely caused by high amounts of side-scatter from UFPM concomitant with higher proportions of POM. Thus, the use of turbidity as a proxy for determining SSC may have serious consequences for the measurement of representative suspended sediment data, particularly in locations where POM may be a significant contributor to overall suspended load.  相似文献   

20.
Particles eroded from hillslopes and exported to rivers are recognized to be composite particles of high internal complexity. Their architecture and composition are known to influence their transport behaviour within the water column relative to discrete particles. To‐date, hillslope erosion studies consider aggregates to be stable once they are detached from the soil matrix. However, lowland rivers and estuaries studies often suggest that particle structure and dynamics are controlled by flocculation within the water column. In order to improve the understanding of particle dynamics along the continuum from hillslopes to the lowland river environment, soil particle behaviour was tested under controlled laboratory conditions. Seven flume erosion and deposition experiments, designed to simulate a natural erosive event, and five shear cell experiments were performed using three contrasting materials: two of them were poorly developed and as such can not be considered as soils, whilst the third one was a calcareous brown soil. These experiments revealed that soil aggregates were prone to disaggregation within the water column and that flocculation may affect their size distribution during transport. Large differences in effective particle size were found between soil types during the rising limb of the bed shear stress sequence. Indeed, at the maximum applied bed shear stress, the aggregated particles median diameter was found to be three times larger for the well‐developed soil than for the two others. Differences were smaller in the falling limb, suggesting that soil aggregates underwent structural changes. However, characterization of particles strength parameters showed that these changes did not fully turn soil aggregates into flocs, but rather into hybrid soil aggregate–floc particles. Copyright © 2013 John Wiley & Sons, Ltd.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号