共查询到20条相似文献，搜索用时 359 毫秒
1.
The present paper deals with the impact of shear deformation on the geometric arrangement of particles within the soil specimen,
which is termed as the microfabric of soil. A series of compression and extension lubricated end triaxial tests are performed
on cylindrical specimens of Kaolinite clay with two extreme microfabrics; dispersed and flocculated, which are obtained using
slurry consolidation technique. Flocculated microfabric has random orientation of particles within the soil mass having face-to-edge
particle contacts; however, dispersed microfabric has parallel orientation of particles containing face-to-face particle contacts.
When the specimen is subjected to large stress levels during its shear deformation, the particle orientation and the geometric
arrangement within the soil specimen gets affected due to the force acting on the clay platelets. The variation in microfabric
of soil before and after shear deformation process is evaluated by obtaining X-ray diffraction patterns of the clay specimen
at three different locations using standard X-ray diffractometer. The discussion includes an analysis of the orientation of
soil particles located at shear banding zones of the clay specimens, which may be useful for understanding the strain localization
development in clays. 相似文献
2.
The effect of microfabric on the mechanical behaviour of clays has been explored previously based on the response of dispersed and flocculated microfabrics only. However, the natural clays often have the geometric arrangement of particles between these two extreme cases which can be termed as intermediate microfabric. This paper explores the formation of intermediate microfabric of kaolin clay and its impact on soil’s consolidation behaviour by performing self-weight consolidation, slurry consolidation and 1-D consolidation tests. The effect of calgon content (dispersing agent) on geometric arrangement of the particles has been evaluated through cluster size distribution by performing double hydrometer tests. Then these clay slurries have been used to perform the AFM (Atomic Force Microscopy) test to obtain the variation in average angle of particle orientation with respect to the calgon content present in the slurry. AFM technique provides 3D image of the clay sample and 2D image with Z-information with the potential of measuring intermediate microfabric of clayey soil quantitatively including dispersed and flocculated microfabrics. Other traditional techniques such as SEM, TEM & XRD are limited to only qualitative analysis of soil’s microfabric, thus, having no capability to measure intermediate microfabric of clay. A methodology of preparing bulk specimens of clay with intermediate microfabric has been developed using slurry consolidation technique; and then these specimens have been consolidated under 1-D loading to evaluate the effect of intermediate microfabric on compressibility and permeability of clay. In this study, all the experiments reports that the dispersed type geometric arrangement increases with the increase in calgon content in soil up to 2 % and then the reverse behaviour is observed at 3 %; which may depend on the required amount of sodium cations to neutralize the negatively charged faces of the clay platelets present in the slurry. 相似文献
3.
不同应力路径下剪切带的数值模拟 总被引：4，自引：1，他引：3
采用回映应力更新算法,编写了基于伏斯列夫面的超固结黏土本构关系模型子程序,嵌入非线性有限元软件ABAQUS。通过对单元试验进行三轴压缩、三轴伸长及平面应变等问题的模型预测,再现了超固结黏土在不同初始超固结比和应力路径时的变形和强度特性,从而验证了子程序的正确性。借助该本构模型,对三轴压缩、三轴伸长及平面应变应力路径下超固结黏土体变形局部化问题,进行了三维数值模拟。分析结果表明：超固结黏土在三轴压缩及伸长状态时,土体变形局部化在应力-应变关系软化时出现,而平面应变状态时,在应力-应变关系硬化阶段出现,其超固结黏土的剪胀特性在剪切带的形成过程中起重要作用。 相似文献
4.
A new method is introduced in this study to identify the microfabric (geometric arrangement of platelets) of cohesive soil
using standard X-ray diffractometer. Various sampling techniques are used to prepare the Kaolinite clay samples with different
microfabrics to assess the consistency and versatility of the proposed method. This method is based on identifying the presence
of basal and prism peaks from the X-ray diffraction pattern and corresponding relative intensity values. The present study
also demonstrates the conditions for which Scanning Electron Micrographs (SEM) are not capable of accurately identifying the
microfabric of cohesive soils. The method proposed in this study uses relative amplitudes of basal and prism peaks avoiding
difficult sample and surface preparation procedures, as used by previous researchers in their microfabric identification methods.
The proposed method is found to be a rapid and accurate method for identifying the microfabric of Kaolinite clay and should
prove to be valuable for routine implementation for studying structured natural clays. 相似文献
5.
Techniques have been developed to prepare reasonably homogeneous, reproducible bulk samples of a kaolinite clay (Hydrite 10) with predetermined microfabrics and to reliably identify these microfabrics both quantitatively and qualitatively. Eight samples with quite diverse histories were produced in the laboratory by controlling the chemistry of the clay-water system, the consolidation stress path (either isotropic or anisotropic), and the magnitude of the consolidation stresses. The fabrics of these samples are identified and quantified by the combined use of scanning electron microscopy, optical microscopy, and X-ray diffractometry, and reasonably comprehensive appraisals of particle associations and orientation are obtained. Anisotropic consolidation was found to induce a preferred particle orientation, whereas isotropic consolidation tended to provide basically random samples. The anisotropically consolidated samples from dispersed slurries exhibited somewhat greater particle orientation than those from flocculated slurries, and, although considerable particle orientation occurred at low values of the consolidation stress, increases in the major principal consolidation stress did accentuate the particle orientation. The presence of domains or small groups of particles is suggested in certain samples, especially in those consolidated isotropically. 相似文献
6.
为探讨南京下蜀土在三轴压缩下的宏观力学性质及微观演化机理,分别通过三轴试验仪和扫描电子显微镜（SEM）研究了下蜀土的宏观变形、强度特性及微结构变化规律。结果表明：下蜀土的结构强度与围压的比值基本上为常数,土体的结构强度与内部颗粒的排列、胶结性能,以及外部应力状态有关。三轴压缩下,随着应变增大,下蜀土中较大颗粒集聚体受剪破坏,而较小颗粒通过聚集增大,使得土体颗粒面积比例增大,但颗粒集团化程度降低,平面分布分散,颗粒排列逐渐朝无序发展,并在无序程度最高部位形成了剪切破坏带。 相似文献
7.
为探讨湛江强结构性原状土与相应重塑土在不同应力路径下的强度特性及其与结构性的关联性,开展了在不同固结条件下的主动压缩、被动压缩、主动伸长3种应力路径试验,分析了该强结构性黏土在不同应力条件下的力学性状与强度特性。结果表明,湛江黏土的剪切破坏形态主要是单一型、双交叉剪切带与“腰鼓”型3类,应力-应变特性主要为轻度应变软化、强烈应变软化、轻度应变硬化、强烈应变硬化4类;偏压固结下试样破坏应变小于等压固结相应值,破坏强度及初始弹性模量比后者大;不同应力路径下土的强度差异主要反映在结构屈服前有效黏聚力的不同,结构屈服前,原状土的黏聚力高于重塑土的黏聚力,内摩擦角小于后者;结构屈服后,黏聚力逐渐减小,内摩擦角略有增大。原状土到重塑土的转变过程是黏聚力与内摩擦力在土体内部相互消长的过程,强结构性黏土在结构屈服前的强度指标具有较强应力路径依赖性。 相似文献
8.
The goal of this study was to analyze the relation between the behaviour of a clayey material at the macroscopic scale and its microfabric evolution. This may lead to a better understanding of macroscopic strain mechanisms especially the contractancy and dilatancy phenomena. The approach proposed in this paper is based on the study of clay particles orientation by SEM picture analysis after different phases of triaxial loading. In the initial state of the samples (one‐dimensional compression), the SEM observations highlight a microstructural anisotropy with a preferential orientation of the particles normal to the loading direction. During isotropic loading, densification of the clayey matrix occurs related to a random orientation of particles indicated by the term ‘depolarization’. In the earlier stages of constant σ3 drained triaxial path on slightly overconsolidated specimens, the microstructural depolarization seems to persist inside a macroscopic domain, in which only the volumetric strains due to the isotropic part of the stress tensor evolve. Then, a rotation mechanism of the particles towards preferred directions seems to be activated. The phenomenon appears directly linked to the evolution of the deviatoric part of the stress tensor. Copyright © 2010 John Wiley & Sons, Ltd. 相似文献
9.
南阳膨胀土裂隙面强度试验研究 总被引：1，自引：0，他引：1
裂隙性是膨胀土的基本特性之一,膨胀土中原生裂隙面的存在往往导致膨胀土边坡的失稳。选取南水北调中线工程南阳段膨胀土进行裂隙面强度特性试验,提出了裂隙面强度三轴试验新方法。首次将计算机X射线断层扫描技术引入裂隙面的强度试验,通过测量裂隙面真实产状,准确分析裂隙面上的破坏应力,提出了裂隙面强度参数的整理方法。研究成果表明,裂隙面的峰值强度不仅远小于两侧土的峰值强度,而且也小于两侧土的残余强度;裂隙面强度较低的原因主要是其具有较高的含水率、蒙脱石含量以及颗粒排列定向度。地下水淋滤作用对于膨胀土裂隙面存在3个方面的影响：微观上使得膨胀土中铁的氧化物由三价转变为二价,形成与两侧土颜色完全不同的灰白色裂隙黏土;细观上改变了母体土的矿物成分和颗粒排列结构,使得裂隙填充物具有较高的蒙脱石含量和颗粒定向度;宏观上形成了裂隙面与两侧土体力学强度的显著差异。 相似文献
10.
以天津滨海新区地下工程涉及较多的9～18m深度海相软土为研究对象,采用应力应变控制式三轴剪切渗透试验仪,分别进行三轴固结不排水试验(CU)、三轴不固结不排水试验(UU)以及模拟基坑开挖卸荷的减p路径试验(DEP),得到滨海软土在不同应力路径下的力学性状与初始固结状态有关。CU与UU试验应力与应变关系曲线呈硬化特征,CU试验孔隙水压力与应变关系呈先剪缩后剪胀的性质;DEP试验应力与应变关系曲线呈软化特征,在等应力控制条件下,孔隙水压力与应变关系呈剪胀性质,孔压为负。DEP试验对于总应力强度参数有影响,对有效应力强度参数影响较小。在滨海软土基坑支护设计中,选用CU试验参数进行计算,设计偏于安全。 相似文献
11.
This paper presents an elasto‐plastic model for unsaturated compacted soils and experimental results obtained from a series of suction‐controlled triaxial tests on unsaturated compacted clay with different initial densities. The initial density dependency of the compacted soil behaviour is modelled by establishing experimental relationships between the initial density and the corresponding yield stress and thereby between the initial density and the location and slope of normal compression line. The model is generalized to three‐dimensional stress states by assuming that the shapes of the failure surface and the yield surface in the deviatoric plane are given by the extended SMP criterion. A considerable number of the isotropic compression, triaxial compression and extension tests on unsaturated compacted clay with different initial densities were performed using a suction‐controllable triaxial apparatus, to measure the stress–strain–volume change in different stress paths and wetting paths. The model has well‐predicting capabilities to reproduce the mechanical behaviour of specimens compacted under different conditions not only in isotropic compression but also in triaxial compression and triaxial extension. Copyright © 2003 John Wiley & Sons, Ltd. 相似文献
12.
黏土颗粒形态不仅反映黏土的矿物组分,更是影响其物理力学性质的重要因素之一。为了研究物质组成对软黏土微宏观性质的影响,采用离散元方法对不同颗粒形态的软黏土试样进行三轴压缩模拟试验。首先,基于扫描电镜图像量化颗粒形态,对天然状态下黏土颗粒的方向角和凹凸度进行统计,引入球度和凹凸度作为颗粒形态的特征参数;然后,基于原生矿物的单粒结构和黏土矿物的片状结构特征,构造球体单粒及圆柱体、正方体、长方体的片状簇体;最后,基于三轴试验离散元模拟方法,分析软黏土颗粒形态对其宏观力学及微观特性的影响。结果表明:片状颗粒试样比球体颗粒试样的初始模量高,抗剪强度大,随加载其排列趋于水平向分布;加载初期,颗粒球度对初始弹性模量影响较明显,初始弹性模量随着球度增大而逐渐减小;加载后期,颗粒凹凸度对抗剪强度指标影响作用逐渐凸显,试样内摩擦角和黏聚力随着凹凸度增大而逐渐减小;微观结构上,颗粒形状对颗粒位移和旋转也有较大影响。 相似文献
13.
不同应力路径下超固结黏土试样变形局部化分析 总被引：2，自引：1，他引：1
基于改进伏斯列夫面超固结黏土三维本构模型,利用有限元软件ABAQUS材料子程序接口,采用回映应力更新算法,实现了该模型在有限元分析中的应用。通过该模型与比奥固结理论的耦合,对超固结比为8的超固结黏土在三轴压缩、三轴伸长及平面应变应力条件下的变形局部化问题,进行了水-土耦合弹塑性有限元分析。分析结果表明：剪切带带内、带外点经历不同应力路径;剪切带带外单元经历了体缩、剪胀及被吸水体缩过程,而剪切带带内单元一直保持剪胀趋势;剪切带的形成伴随着剪胀,剪切带内、外出现了负的孔压,且孔压的分布也具有局部化特性。关于剪切带带内、外的孔隙水压及体变变化趋势与剪切速率有关,而平面应变介于三轴压缩与三轴伸长之间,但平面应变较早出现剪切带。孔隙水的迁移速度影响剪切带带内单元的剪胀,进而影响剪切带的形成及发展;而围压和弱单元位置也对剪切带的形成也有影响。 相似文献
14.
土工格室加筋土的大尺寸直剪试验研究 总被引：4，自引：0，他引：4
采用自行研制的500 mm?500 mm?400 mm（长?宽?高）大尺寸直剪仪,对土工格室加筋土以及土工格室加筋水泥稳定土的剪切性能进行了试验研究。通过大尺寸直剪试验模拟土工格室加筋土的剪切作用过程,得出加筋土剪切应力与剪切应变关系为非线性确定了土工格室加筋土的抗剪强度指标以及土工格室对土的抗剪强度增强机理,土工格室加筋土的黏聚力提高较大,内摩擦角变化相对较小。通过对素土和掺入量为5 %的水泥稳定土进行常规直剪试验、大尺寸直剪试验和三轴压缩试验对比分析,探讨不同试验方法对抗剪强度指标的影响,得出3种试验方法对应的抗剪强度指标及其相对大小;即素土的摩擦角大小依次为：三轴试验小于大尺寸直剪试验小于常规直剪试验,素土的黏聚力大小依次为：大尺寸直剪试验小于三轴试验小于常规直剪试验;水泥稳定土的摩擦角大小为：三轴试验小于大尺寸直剪试验,黏聚力结果比较大小依次为：三轴试验小于大尺寸直剪试验。 相似文献
15.
The objective of this study is to derive an effective stress‐based constitutive law capable of predicting rate‐dependent stress–strain, stress path and undrained shear strength and creep behavior. The flow rule used in the MIT‐E3 model and viscoplasticity theory is employed in the derivation. The model adopts the yield surface capable of representing the yield behavior of the Taipei silty clay and assumes that it is initially symmetric about the K0‐line. A method is then developed to compute the gyration and expansion of the loading surface to simulate the anisotropic behavior due to the principal stress rotation after shear. There are 11 parameters required for the model to describe the soil behavior and six of them are exactly the same as those used in the Modified Cam‐clay model. The five additional parameters can be obtained by parametric studies or conventional soil tests, such as consolidation tests, triaxial compression and extension tests. Finally, verification of the model for the anisotropic behavior, creep behavior and the rate‐dependent undrained stress–strain and shear strength of the Taipei silty clay is conducted. Copyright © 2010 John Wiley & Sons, Ltd. 相似文献
16.
Undisturbed specimens of a soft clayey silt have been taken vertically, horizontally and at 45° to the vertical at the base of a trench and submitted to consolidation and undrained triaxial compression and extension tests in the laboratory. Undrained shear strengths and compressibilities are found to be strongly dependent on sample orientation, but the effective stress strength parameters are shown to be much more influenced by stress path than sample orientation. The pore-pressure response vs axial strain is shown to be unaffected by sample orientation. Most of the anisotropic effects are shown to be eliminated by successively consolidating the specimens under isotropic pressure increments and re-testing in undrained shear. Some of the evidence from the experimental programme indicates that tension resisting bonds act between the grains of the soil specimens. 相似文献
17.
土体结构性的数学模型是21世纪土力学的核心问题。由于土体微观结构的变化造成了重塑土与原状土的力学特性上的差异。采用应变型和应力型结构性宏观参数来表征这种微观结构的变化,同时将应变性结构性参数引入到等向固结过程中去,用以描述常规三轴试验中剪切前的等向固结过程以及剪切时球应力对结构性土体的影响。实现应变型和应力型结构性宏观参数对整个三轴剪切过程的描述。修正剑桥模型对正常固结重塑黏土的三轴压缩试验能做出准确地描述,但对超固结黏土及原状土,即具有结构地土体,则不能给出准确地描述。将应变型和应力型结构性宏观参数引入到修正剑桥模型中,实现修正剑桥模型的结构化。该结构性修正剑桥模型参数的确定方法与常规修正剑桥模型参数的确定方法相差不多,只不过多了球应力与土体结构性体应变的关系式、偏应力与土体结构性广义剪应变的关系式。经过数值模拟比较,结构性修正的剑桥模型能较好地反映原状土的结构性演化过程,能描述原状土结构的整个破坏过程,在多种应力路径下具有很好的预测作用。 相似文献
18.
利用GDS应力路径三轴试验系统对南阳膨胀土进行3种应力速率下、4种超固结比（OCR）的被动压缩三轴试验及3种超固结比的被动挤伸三轴试验,分析了不同超固结比和应力速率下其应力（孔隙水压力）-应变关系、有效应力路径及变形模量的演化规律,对膨胀土变形模量各向异性特性进行了初步探讨。结果表明,应力速率、超固结比及卸荷路径均对膨胀土力学特性有一定影响。在被动压缩路径和被动挤伸路径下,随着应力速率和超固结比的增加,相同轴向应变时的偏应力值单调增加;不同超固结比和应力速率时膨胀土的孔隙水压力始终为负值,且其降幅总体上随超固结比的增加而增大,但其降幅随应力速率的变化规律与剪切路径有关。在被动压缩路径下,相同应变时不同应力速率下的孔压降幅基本相同;而在被动挤伸路径下,其降幅随应力速率的增加而增大。边坡开挖路径的选择对于边坡变形影响显著,被动挤伸路径下达到设定极限偏应力时的轴向应变明显大于被动压缩路径。膨胀土变形模量E100随着超固结比和应力速率的增加而增加,但各应力速率下变形模量的各向异性特性则随着超固结比的增加而变弱。 相似文献
19.
通过GDS三轴试验系统对K0固结原状南阳膨胀土原状样进行了不同卸荷速率和卸荷路径下的不排水三轴剪切试验,在试验资料的基础上,建立了K0固结膨胀土的初始切线模量Ei和极限偏应力qult与固结应力及卸荷速率的关系式。发现,K0固结膨胀土在卸荷剪切过程中的应力-应变关系曲线呈典型双曲线特征;膨胀土的不排水剪切强度随轴向固结应力及卸荷速率的增加而单调增加;Ei及qult随固结应力及卸荷速率的变化规律与强度基本类似,但Ei随固结应力的增加呈指数增加,而qult则表现为线性增加。通过改进邓肯-张双曲线表达式,建立了K0固结膨胀土下不同卸荷速率时应力-应变关系的预测公式,并进行了模型验证。 相似文献
20.
Jean-Herv Prvost 《国际地质力学数值与分析法杂志》1977,1(2):195-216
The proposed general analytical model describes the anisotropic, elasto-plastic, path-dependent, stress-strain-strength properties of inviscid saturated clays under undrained loading conditions. The model combines properties of isotropic and kinematic plasticity by introducing the concept of a field of plastic moduli which is defined in stress space by the relative configuration of yield surfaces. For any loading (or unloading) history, the instantaneous configuration is determined by calculating the translation and contraction (or expansion) of each yield surface. The stress-strain behaviour of clays can thus be determined for complex loading paths and in particular for cyclic loadings. The stress-strain relationships are provided for use in finite element analyses. The model parameters required to characterize the behaviour of any given clay can be derived entirely from conventional triaxial or simple shear soil test results. The model's extreme versatility is demonstrated by using it to formulate the behaviour of the Drammen clay under both monotonic and cyclic loading conditions. The parameters are determined by using solely the results from monotonic and cyclic strain-controlled simple shear experimental tests, and the model's accuracy is evaluated by applying it to predict the results of other tests such as (1) cyclic stress-controlled simple shear tests, (2) monotonic triaxial loading compression and unloading extension tests, and (3) cyclic stress- and strain-controlled triaxial tests on, this same clay. The theoretical predictions are found to agree extremely well with the experimental test results. 相似文献