共查询到19条相似文献，搜索用时 140 毫秒
1.
采用光滑粒子流体动力学（SPH）方法,建立了刚体入水六自由度响应模型,实现了波浪环境下小型回转体高速入水过程的数值模拟。对波浪环境下小型回转体高速入水过程中的运动姿态、冲击载荷进行讨论分析,结果表明：波浪条件下入水点相位不同,导致回转体实际入水角不同,实际入水角越大,入水冲击载荷越大,弹道越稳定;实际入水角越小,入水冲击载荷越小,弹道越易发生失稳。本研究表明,入水点相位对小型回转体弹道特性和冲击载荷产生影响,进而为波浪条件下跨介质武器低载稳定入水提供基础性技术支撑。 相似文献
2.
锥形振荡浮子在波浪能转换装置中应用非常广泛,在其服役期间,由于较小的设计吃水深度或为防避极端海况的需要,它们经常会离开水面;当其再次入水的时候,浮子底部就会受到入水冲击。入水冲击总是伴随着巨大的冲击压强以及冲击载荷,会导致浮子的结构性及疲劳性破坏,从而影响浮子的工作寿命。基于Fluent软件对锥形浮子的入水冲击过程进行了模拟仿真,研究了具有不同斜升角的锥体在入水冲击过程中所受的冲击压强、冲击载荷、冲击速度的时空变化规律,以及各冲击参数之间的关系。结果发现:(1)锥形浮子在入水瞬间的毫秒量级时间内受到极大的冲击压强和冲击载荷;(2)最大压强出现在锥顶点处,且锥顶点压强和锥表面压强之间的差距随着入水深度的增加而逐渐减小;(3)锥顶点压强峰值早于冲击载荷峰值而出现,并且两者之间的时间间隔随着锥体斜升角的增加而增大;(4)其他条件不变时,斜升角越小的锥体其所受的入水冲击越大。 相似文献
3.
李蹬珺 《数字海洋与水下攻防》2020,3(5):431-436
空投航行体入水弹道控制问题一直是空投航行体研究的重点，针对空投航行体入水弹道控制问题，建立了航行体的六自由度非线性动力学和运动学模型；根据入水弹道对姿态控制的要求，通过设计基于PID控制三通道姿态控制策略解决其入水控制问题，并且通过MATLAB进行仿真验证。结果表明：在不同的初始入水条件下，本文研究的控制策略都能够较好地对航行体入水深度及姿态进行控制，具有一定的实际应用价值。 相似文献
4.
5.
楔形体在波浪中自由入水的数值模拟 总被引：1，自引：0，他引：1
物体入水时波浪的影响不可忽略,基于流体力学模型采用VOF法,并利用自定义函数,模拟了楔形体的自由入水过程;同时结合推波板原理及海绵层消波理论实现了数值水槽的造消波,完成了波浪中楔形体自由入水的模拟,计算了楔形体入水时所受的水作用力、自由液面变化及物面压强分布等,研究了不同波高、周期以及在波浪不同位置入水时对楔形体的影响。结果表明:本文建立的数值模型可很好地模拟楔形体入水造成的射流及空泡的形成发展过程,波浪对楔形体入水的影响主要由波浪内部流场变化及表面波形决定,在波浪不同位置处入水对楔形体受力及入水形态均有较大影响。 相似文献
6.
刘超维 《数字海洋与水下攻防》2021,4(4):328-333
为了探究航行器在跨介质过程中的动力学响应,基于任意拉格朗日-欧拉(ALE)方法建立航行器跨介质数值计算模型,仿真分析了不同初始参数对航行器跨介质冲击载荷的影响规律,给出了最大冲击载荷与跨介质速度与跨介质角度之前的函数关系。研究结果可为航行器跨介质弹道及结构设计提供参考。 相似文献
7.
8.
根据IEC61400-3设定工况,采用NREL开发的5 MW风机基础模型,应用FAST,以Aero-Hydro-Servo-Elastic耦合仿真技术对风机进行研究。对时域仿真得到的短期载荷,应用分块极大值法联合Gumbel分布外推计算风机极限载荷;以雨流计数法、线性累积损伤理论和S-N曲线为理论基础应用MLife软件,计算风机疲劳载荷。对比分析不同工况下浮式风机、近海单桩风机和陆上风机的极限载荷与疲劳载荷,进而探讨影响浮式风机动态响应的因素。结果表明,对于陆上风机和近海单桩风机,风是其主要载荷来源;而波浪是浮式风机主要载荷来源。对风机进行设计要根据特定海域统计的海洋气候条件,避免风机及其支撑结构的固有频率与波浪频率近似而产生共振;风机制造装配在一定误差范围内,质量不平衡对风机载荷几乎没有影响。 相似文献
9.
振荡浮子在波浪能转换装置中应用非常广泛,在其服役期间,由于较小的设计吃水深度或为防避极端海况的需要,它们经常会离开水面;当其再次入水的时候,浮子底部就会受到入水冲击。入水冲击总是伴随着巨大的冲击压强以及冲击载荷,会导致浮子的结构性及疲劳性破坏,从而影响浮子的工作寿命。本文对锥形、半球形和横圆柱形三种形状的浮子入水冲击过程进行了实验研究,分析了浮子表面压强和冲击加速度的变化规律。主要结论如下:(1)在巨大的水阻力作用下,入水瞬间三种浮子表面压强急剧上升,迅速达到最高峰值;之后由于空气垫的作用,压强出现二次峰值现象。(2)在空气垫的作用下,三种浮子的最高压强峰值均未出现在浮子的最低点处,而是出现在外围某处。(3)三种浮子在触水瞬间的加速度均达到hm/s~2的量级,而后急剧下降,并在较短时间内达到一平衡值并沿其小幅震荡。(4)横圆柱形浮子由于其非垂直轴对称性,其表面压强和加速度的震荡更加明显。 相似文献
10.
斜压海洋动力学的一种三维数值模式──Ⅱ.温度、盐度和垂直涡动粘性系数的计算 总被引：2，自引：0，他引：2
根据海水温度和盐度平流扩散方程给出一种数值计算方案并采用混合长度理论给出垂直涡动粘性系数的计算方法。对于温度和盐度方程,其平流过程采用了Lax－Wendroff格式,水平扩散采用显格式,垂直扩散采用隐格式。时间步长主要受平流过程的Courant-Friedrichs-Lewy条件限制。垂直涡动粘性系数计算依据Prandtl混合长度理论,并考虑了海水层化的抑制作用,因而其数值与流场及密度场结构有关。温度、盐度及垂直涡动粘性系数的计算与动力方程中内模态的计算同步进行。应用本模式模拟渤、黄、东海由潮流、密度流和风海流迭加而成的综合海流,得出了良好的结果。 相似文献
11.
The high-speed water entry process of an autonomous underwater vehicle (AUV) has a strong impact nonlinearity, and a cavity formed by air and water will often be generated as part of the entry process. The shape of the water-entry cavity plays an important role in the load characteristics and stability of the water-entry trajectory. In this paper, a numerical model for describing the cavity and impact load characteristics of a high-speed water-entry AUV is established. The simulation results such as cavity shape and impact load are compared with experimental data. The good agreement between the numerical results and those of the experiments reveals the accuracy and capability of the numerical algorithm. Subsequently, the arbitrary Lagrange-Euler (ALE) numerical algorithm is used to simulate and analyse the variation laws of the cavity characteristics and impact loads with different head shapes, water-entry velocities, water-entry angles and angles of attack. The results obtained in this study can provide a good reference for the trajectory control and structural design of the AUV. 相似文献
12.
《Oceanologica Acta》1998,21(5):623-630
An analysis is made of the spectral distribution curves of the light attenuation coefficient in natural water areas and artificial roily oils in sea water samples under various conditions of salinity and storage time, using the approximate formulae based on the Mie theory. 相似文献
13.
Much attention should be paid to a large FPSO moored permanently in an oil field with water depth of only about 20 m, since shallow water effects on the hydrodynamics may bring about collision and damage. A 160kDWT FPSO with a permanent soft yoke mooring system is investigated with various shallow water depths and focuses are the low frequency surge motion and mooring load. Computation for the FPSO system is made based on linear 3-D potential fluid theory and time-domain numerical simulation method. Corresponding model test is carried out in the ocean engineering basin of Shanghai Jiao Tong University. It is shown that, in the surge natural period, low frequency surge motion and mooring force increase remarkably with the decrease of water depth. Especially, the smaller the ratio of water depth and draught is, the quicker the increase is. The shallow water effects should be taken into account carefully for determining the design load of a single point mooring system. 相似文献
14.
Impact problems associated with water entry have important applications in various aspects of naval architecture and ocean engineering. Estimation of hydrodynamic impact forces especially during the first instances after the impact is very important and is of interest. Since the estimation of hydrodynamic impact load plays an important role in safe design and also in evaluation of structural weight and costs, it is better to use a reliable and accurate prediction method instead of a simple estimation resulted by analyzing methods. In landing of flying boats, some phenomena such as weather conditions and strong winds can cause asymmetric instead of symmetric descent. In this paper, a numerical simulation of the asymmetric impact of a wedge, as the step of a flying boat, considering dynamic equations in two-phase flow is taken into account. The dynamic motion of the wedge in two-phase flow is solved based on finite volume method with volume of fluid (VOF) scheme considering dynamic equations. Then the effects of different angles of impact and water depth on the velocity change and slamming forces in an asymmetric impact are investigated. The comparison between the simulation results and experimental data verifies the accuracy of the method applied in the present study. 相似文献
15.
基于潜艇被动声呐系统跟踪目标,进行目标运动分析后，发射线导鱼雷攻击水面舰艇的作战背景,建立了鱼雷导引方法、声呐目标分辨和目标运动分析的数学模型,通过仿真研究了鱼雷发射后本艇战术机动对线导鱼雷攻击远距离水面攻击效能的影响。根据鱼雷作战效能蒙特卡洛仿真方法,给出在一定目标运动要素误差下,满足线导鱼雷攻击效能指标的鱼雷发射后的本艇战术机动的要求,并给出了武器系统实现这种要求的设计方案。 相似文献
16.
The paper studies the parametric stochastic roll motion in the random waves. The differential equation of the ship parametric roll under random wave is established with considering the nonlinear damping and ship speed. Random sea surface is treated as a narrow-band stochastic process, and the stochastic parametric excitation is studied based on the effective wave theory. The nonlinear restored arm function obtained from the numerical simulation is expressed as the approximate analytic function. By using the stochastic averaging method, the differential equation of motion is transformed into Ito's stochastic differential equation. The steady-state probability density function of roll motion is obtained, and the results are validated with the numerical simulation and model test. 相似文献
17.
本文根据黄河口海域的特点,提出了一个新的模式描述沉积过程。将岩芯分成几个较大的部份,每一部份都代表一种沉积环境。在一种沉积环境中,输沙量虽有波动,但这种波动是有周期性的。在不同的周期中,可以认为。~(210)Pb的沉积通量是恒定的。计算不同层段之间的沉积时间可以采用公式: 由于输沙量的周期性变化,沉积物的含水量也往往呈现有规律的周期性变化。文中求出了各岩芯含水量W与。~(210)Pb含量之间的回归方程式,发现相关系数普遍较高。 相似文献
18.
重物在落水和着底过程中都会产生瞬态声信号,这类信号可被运用于浅水区域水下目标定位。 针对浅水区域目标定位的问题,提出了一种基于小型立体五元基阵的瞬态声源快速被动定位算法。 在分析重物落水信号特征的基础上,选取合适的广义互相关加权函数求得传声器之间的声程差,运用快速最小二乘搜索算法进行声源定位。 结果表明:运用 5 传声器阵列可以同时兼顾定位精度和鲁棒性,且满足实时性要求,该方法可运用于浅水区域瞬态声源定位等领域。 相似文献
19.
In this study, an efficient reliability-based design tool for stone-filled crib seawalls is developed. The first-order reliability method is integrated into spreadsheet to facilitate the reliability analysis for practical application. Using this spreadsheet tool, the effects of several major uncertain factors on the seawall design, including design water level, material property, and wave forces, are explicitly explored. In addition, the impact of progressive scour on the seawall stability is demonstrated through a time-dependent reliability analysis. This developed reliability-based design tool for seawalls is validated through comparing with the Monte Carlo simulation. This seawall design tool is easy to use and can be readily adapted in various aspects in the seawall design for shoreline protection. 相似文献