共查询到19条相似文献，搜索用时 105 毫秒
1.
高层隔震结构非线性地震响应分析及设计方法研究 总被引：3，自引：0，他引：3
高层隔震结构的分析理论和设计方法是目前隔震技术向高层建筑推广的2个关键理论问题。本文以高烈度区宿迁市已经竣工的高层隔震建筑阳光大厦为工程实例,对高层隔震结构的非线性地震响应分析方法进行了研究,包括隔震支座竖向不同拉压刚度的模拟、各种类型的隔震支座水平力学特性的准确模拟,以及不同地震动输入方式和输入角度对隔震支座受拉情况的影响分析等;在此基础上,对隔震层的设计方法进行了分析,提出了隔震层设计的基本原则,进而给出了控制隔震层设计的基本指标,包括隔震支座的长期面压、极值面压、隔震层偏心率等;最后,对高层隔震结构的相关构造要求进行了必要的说明。 相似文献
2.
在已有研究基础上,为提高摩擦型组合隔震支座变形能力、改进各摩擦组件位移协调性,建立实体化和参数化计算模型,对新型三段两级摩擦组合隔震支座进行构造及内力分析研究,使用ABAQUS软件对摩擦阻尼器和组合隔震支座进行实体有限元模拟。针对设置常规隔震支座和新型组合隔震支座的某隔震结构案例进行建模及非线性时程地震响应分析,推导组合隔震支座出力和构造参数的关系。研究结果表明,文章所采用的摩擦阻尼器参数化建模方法是准确的,新型组合支座可明显降低支座拉应力,减小隔震层位移,提高结构抗倾覆能力。文章提出的针对摩擦阻尼器的简化单元可大幅提高有限元模型的计算效率。 相似文献
3.
对于近断层处高烈度区高层剪力墙结构，传统设计难以解决墙体太厚、配筋太大等难题。为研究在考虑近断层影响下高烈度区剪力墙住宅采用隔震设计的技术可行性，采用隔震设计对某剪力墙结构工程进行全面分析。对比分析常规剪力墙结构方案及增设橡胶隔震支座的隔震方案，分析结果表明，隔震方案较常规方案前3阶结构自振周期延长约3倍，从而有效减小了上部结构的地震作用；在设防烈度地震作用下，结构水平向减震系数为0.281，上部结构所受水平地震作用和抗震措施可按降低一度进行设计；罕遇地震作用下隔震支座性能稳定，上部结构基本处于弹性工作状态。研究结论可为隔震支座设计和进一步研究提供参考。 相似文献
4.
5.
在高烈度区高层框剪结构引入隔震技术,其目的是尽量减小地震荷载,增大结构处在弹性变形的适应范围,使抗震阶段的设计目标更易于实现和确保。将隔震体系简化分析模型引入高层框剪隔震体系,研究隔震支座厚度变化对框剪隔震体系地震反应的影响,并在高烈度设防烈度地震下进行结构动力时程分析。计算结果说明:加高隔震支座厚度,可以在一定程度上减小框剪隔震体系的地震荷载。设防烈度地震下,8度时上部结构自振周期为1~2s的框剪隔震体系完全能满足现行规范位移限值要求,8.5度上部结构自振周期为1~1.4s的框剪隔震体系也能满足现行规范位移限值要求,在9度时一般无法满足设计要求。 相似文献
6.
高层隔震建筑的隔震层在罕遇地震作用下会产生拉应力。本文通过对一栋20层的高层隔震结构,分别采用等拉压刚度模型和不等拉压刚度模型进行动力非线性时程分析,研究叠层橡胶隔震支座竖向刚度模型对高层基础隔震结构动力响应的影响。研究表明,超出线弹性工作范围后,竖向等拉压刚度模型将会低估隔震层的竖向位移量,低估上部结构的动力响应。 相似文献
7.
8.
9.
《世界地震工程》2016,(4)
采用大型通用软件Abaqus对某拟建高层建筑进行了隔震动力时程分析,隔震支座分别采用拉压等刚度(等刚度模型),拉压不等刚度(不等刚度模型)和释放抗拉刚度(提离模型)3种支座模型,对比了3种支座模型下隔震结构体系的弹性和弹塑性时程响应,包括层间位移角、基底剪力、隔震层位移、支座拉力和支座竖向位移。结果表明:(1)假定上部结构为弹性的隔震体系响应与相应弹塑性体系的响应存在一定的差异,建议罕遇地震分析采用弹塑性模型;(2)支座等刚度模型与不等刚度模型的支座拉力,弹性分析时明显大于规范限值,弹塑性分析时减小,但仍大于规范限值;(3)提离模型能避免支座受拉,而对上部结构弹塑性响应影响较小,对隔震层水平响应基本无影响。 相似文献
10.
高层隔震建筑设计中隔震支座受拉问题分析 总被引：11，自引：0，他引：11
高层建筑由于高宽比相对较大,倾覆效应明显,当采用隔震技术时,有可能使隔震支座出现拉应力,而通常使用的叠层橡胶隔震支座抗拉能力不强。因此,隔震支座受拉问题成为隔震技术在高层建筑中推广应用的主要障碍之一。本文提出了避免隔震支座受拉的上部结构布置原则及隔震层优化设计方法,并对目前隔震支座拉应力计算方法提出了改进建议。本文的研究工作可为工程设计提供借鉴,为隔震设计相关规范的修订提供依据。 相似文献
11.
The nuclear accident at Fukushima Daiichi in March 2011 has led the nuclear community to consider seismic isolation for new large light water and small modular reactors to withstand the effects of beyond design basis loadings, including extreme earthquakes. The United States Nuclear Regulatory Commission is sponsoring a research project that will quantify the response of low damping rubber (LDR) and lead rubber (LR) bearings under loadings associated with extreme earthquakes. Under design basis loadings, the response of an elastomeric bearing is not expected to deviate from well‐established numerical models, and bearings are not expected to experience net tension. However, under extended or beyond design basis shaking, elastomer shear strains may exceed 300% in regions of high seismic hazard, bearings may experience net tension, the compression and tension stiffness will be affected by isolator lateral displacement, and the properties of the lead core in LR bearings will degrade in the short‐term because of substantial energy dissipation. New mathematical models of LDR and LR bearings are presented for the analysis of base isolated structures under design and beyond design basis shaking, explicitly considering both the effects of lateral displacement and cyclic vertical and horizontal loading. These mathematical models extend the available formulations in shear and compression. Phenomenological models are presented to describe the behavior of elastomeric isolation bearings in tension, including the cavitation and post‐cavitation behavior. The elastic mechanical properties make use of the two‐spring model. Strength degradation of LR bearing under cyclic shear loading due to heating of lead core is incorporated. The bilinear area reduction method is used to include variation of critical buckling load capacity with lateral displacement. The numerical models are coded in OpenSees, and the results of numerical analysis are compared with test data. The effect of different parameters on the response is investigated through a series of analyses. Copyright © 2014 John Wiley & Sons, Ltd. 相似文献
12.
Investigation of the seismic response of high‐rise buildings supported on tension‐resistant elastomeric isolation bearings 
下载免费PDF全文
下载免费PDF全文 In many applications of seismic isolation, such as in high‐rise construction, lightweight construction, and structures with large height‐to‐width aspect ratios, significant tension forces can develop in bearings, raising concerns about the possible rupture of elastomeric bearings and the uplift of sliding bearings. In this paper, a novel tension‐resistant lead plug rubber bearing (TLRB) with improved tension‐resisting capabilities is developed and experimentally and numerically assessed. This TLRB consists of a common lead plug rubber bearing (LRB) and several helical springs. After describing the theory underlying the behavior of the TLRB, the mechanical properties of reduced‐scale prototype bearings are investigated through extensive horizontal and vertical loading tests. The test results indicate that TLRBs can improve the shear stiffness and tension resistance capacity even under significant tensile loads. A series of shaking table tests on scaled models of high‐rise buildings with different aspect ratios were conducted to investigate the dynamic performance of the TLRB and the seismic responses of base‐isolated high‐rise buildings. Three different cases were considered in the shaking table tests: a fixed base condition and the use of TLRB and LRB isolation systems. The results of the shaking table test show that (a) base‐isolated systems are effective in reducing the structural responses of high‐rise buildings; (b) an isolated structure's aspect ratio is an important factor influencing its dynamic response; (c) TLRBs can endure large tensile stresses and avoid rupture on rubber bearings under strong earthquakes; and (d) the experimental and numerical results of the responses of the models show good agreement. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
13.
为研究梯段板下端设置隔震防倒塌支座和楼梯间位置对钢筋混凝土框架结构抗震性能的影响,利用ETABS软件建立不包括、包括隔震防倒塌支座的3种楼梯间布置方案,6个框架结构计算模型。通过模态分析、反应谱分析和Pushover分析,研究隔震防倒塌支座和楼梯间位置对框架结构的振型、内力及破坏机制的影响。结果表明:梯段板下端设置隔震防倒塌支座后,楼梯间位置对钢筋混凝土框架结构的扭转效应影响较小,且框架结构在两个主轴方向的动力特性比较接近;楼梯间框架柱内力均显著降低,但楼梯间布置在最边跨时,在垂直于梯跑方向地震作用下,框架结构边柱内力较大;框架梁对整体框架结构的耗能贡献较多,增强了框架结构的抗震性能,大震时楼梯构件严重破坏较晚,设置隔震防倒塌支座可保证楼梯整体稳定性。 相似文献
14.
15.
The seismic response of light secondary systems in a building is dependent on the response of the primary structural system to the seismic ground motion with the result that very high accelerations can be induced in such secondary systems. This response can be reduced through the use of aseismic base isolation which is a design strategy whereby the entire building can be decoupled from the damaging horizontal components of seismic ground motion by the use of some form of isolation system. The paper presents a theoretical analysis of the response of light equipment in isolated structures and a parallel experimental programme both of which show that the use of base isolation can not only attenuate the response of the primary structural system but also reduce the response of secondary systems. Thus, the design of equipment and piping in a base-isolated building is very much simpler than that for a conventionally founded structure: inelastic response and equipment-structure interaction need not be considered and multiple support response analysis is rendered unnecessary. Although an isolation system with linear elastic bearings can reduce the acceleration of the structure, it may be accompanied by large relative displacements between the structure and the ground. A system using lead-rubber hysteretic bearings, having a force-displacement relation which is approximately a bilinear loop, can reduce these displacements. A parallel experimental programme was carried out to investigate the response of light equipment in structures isolated using lead-rubber bearings. The experimental results show that these bearings can dissipate energy and limit the displacement and acceleration of the structure but are less effective in reducing the accelerations in the internal equipment. The results of both the analysis and the tests show that base isolation is a very effective method for the seismic protection of light equipment items in buildings. 相似文献
16.
利用大型结构分析软件建立了空心薄壁高墩大跨T形刚构桥的空间抗震有限元模型,运用非线性动态时程反应方法进行了高烈度地震区罕遇地震作用下的弹塑性地震反应计算,并与线性时程法和反应谱法的计算结果进行了对比.同时对该结构的延性抗震性能进行了分析评价.结果表明空心薄壁高墩T形刚构铁路桥在罕遇地震下处于较弱的非线性受力状态,其受到的损伤仍然很小,具有较好的抗震能力,结构考虑非线性塑性反应后的地震力与弹性相比明显减小. 相似文献
17.
18.
为了研究铅芯橡胶支座(LRB)和板式橡胶支座(RB)对连续梁桥地震响应及隔震效果的影响,分别采用Bouc - Wen滞回恢复力模型模拟LRB的力-位移非线性特性,采用直线型恢复力模型模拟RB的本构关系,通过结构离散建立了非隔震、LRB隔震和RB隔震3种连续梁桥的有限元计算模型,运用四阶显式Runge - Kutta迭代法和Newmark时间积分法联合求解增量形式的全桥动力微分方程,并结合算例对3种连续梁桥有限元计算模型分别输入汶川地震波进行非线性时程对比分析.结果表明:LRB在控制梁体与支座位移,降低结构加速度和墩、台底内力响应方面均比RB的效果要显著;采用RB隔震后,梁体与支座的位移响应均较大,在桥梁隔震设计时要予以充分重视. 相似文献
19.
The convex model approach is applied to derive the robust seismic fragility curves of a five-span isolated continuous girder bridge with lead rubber bearings (LRB) in China. The uncertainty of structure parameters (the yield force and the post-yield stiffness of LRB, the yield strength of steel bars, etc.) are considered in the convex model, and the uncertainty of earthquake ground motions is also taken into account by selecting 40 earthquake excitations of peak ground acceleration magnitudes ranging from 0.125 to 1.126 g. A 3-D finite element model is employed using the software package OpenSees by considering the nonlinearity in the bridge piers and the isolation bearings. Section ductility of piers and shearing strain isolation bearings are treated as damage indices. The cloud method and convex model approach are used to construct the seismic fragility curves of the bridge components (LRB and bridge piers) and the bridge system, respectively. The numerical results indicate that seismic fragility of the bridge system and bridge components will be underestimated without considering the uncertainty of structural parameters. Therefore, the failure probability P f,max had better be served as the seismic fragility, especially, the fragility of the bridge system is largely dictated by the fragility of LRB. Finally, the probabilistic seismic performance evaluation of the bridge is carried out according to the structural seismic risk estimate method. 相似文献