共查询到14条相似文献，搜索用时 171 毫秒
1.
基于动态耦合的FPSO串靠外输所需拖力快速预报 总被引：1，自引：0，他引：1
以极浅水作业水深的FPSO串靠外输作业为背景,研究穿梭油轮尾部定位拖轮所需拖力大小,提出了基于动态耦合效应的拖轮拖力直接计算方法。基于三维势流理论,考虑浮式生产储油平台(FPSO)与穿梭油轮之间相互水动力干扰,进行动态耦合计算,根据力学平衡原理求得所需的拖轮拖力并分析其影响因素。结果表明:动态耦合模型算出的所需拖力值较之准动态模型更安全、经济;当FPSO与穿梭油轮距离为80 m时,既能保证外输安全性又能保证经济性;增大两船间距、增加穿梭油轮吃水、两船间采用双缆系泊,均能有效降低所需的拖轮拖力。研究结果可为FPSO串靠外输作业操作提供指导,具有一定的工程实用性。 相似文献
2.
针对100 m作业水深的八角形FPSO,提出采用穿梭油轮串靠的外输方案,研究串靠外输在南海的适用性。建立由八角形FPSO及其系泊系统、穿梭油轮及FPSO与穿梭油轮之间的系泊大缆等组成的浮式多体动力学模型,根据多浮体动力学理论进行耦合时域模拟。在外输海况条件下,分析了串靠连接的环境适应性及研究大缆载荷的响应特性,对连接大缆的长度、刚度等关键参数进行了敏感性分析。研究表明,串靠外输的形式对于八角FPSO具有足够的安全性和可靠性,系泊大缆受到明显的冲击张力,张力的幅值受大缆的长度和刚度影响较大。 相似文献
3.
针对1 000 m水深作业的新型圆筒型浮式生产储卸油系统（FPSO）,选择多点系泊FPSO和穿梭油轮串靠外输方案,分析串靠方案在中国南海的可行性。FPSO和穿梭油轮作业时两者之间相互影响的研究较为重要,通过ANSYS-AQWA建立水动力耦合分析模型,基于多浮体水动力学方法进行时域耦合仿真模拟。在FPSO作业海况下,分析了串靠外输时系泊锚链及系泊大缆的张力特性和两浮体的运动响应,对大缆的长度和刚度参数变化进行了分析。结果表明：串靠外输方案满足新型圆筒型FPSO的作业环境。随着系泊大缆长度增加,其张力最值逐渐减小,FPSO和穿梭油轮的最小间距逐渐增大。两浮体最小距离稳定在83 m左右。随着系泊大缆刚度增加,其张力最值增大,相比于大缆长度,大缆刚度对耦合系统的影响较弱。 相似文献
4.
5.
FPSO与穿梭油轮进行串靠外输过程中,穿梭油轮首部可能与FPSO尾部发生碰撞事故,称为"尾碰"。目前的相关研究主要集中在碰撞过程中的风险分析,缺少对FPSO"尾碰"事故碰撞性能的合理分析与评估。本文针对某15万吨级FPSO,基于动态非线性有限元分析软件ABAQUS,采用同步损伤分析技术,研究了串靠外输过程中FPSO与穿梭油轮之间由于过分纵荡运动而引起的碰撞事故。通过数值仿真计算,分析了包括"尾碰"后结构的损伤变形、应力应变关系、碰撞力和吸能情况的船舶碰撞内部动力学,进而对FPSO尾部结构的碰撞性能进行评估。结果表明,FPSO尾部结构中板材结构吸收的能量约占尾部结构总吸能的75.5%,其吸能能力显著优于T型骨材结构,研究结果对FPSO尾部结构的耐撞性设计具有一定的参考意义。 相似文献
6.
7.
系泊系统的定位能力是浅水油田作业的软刚臂式单点系泊FPSO安全作业的重要保障,为研究不同水深/吃水比下单点系泊系统的受力性能,针对一艘16万吨级软刚臂单点系泊FPSO,在线性三维势流理论的基础上,基于多体动力学方法,建立FPSO-系泊腿-软刚臂的耦合模型,采用Newman近似法和Pinkster近似法分析了FPSO所受二阶波浪力,在时域内计算了不同水深/吃水比对系泊系统动力响应性能的影响。结果表明,随着水深/吃水比的增加,Newman近似法计算得到二阶波浪力先增大后减小,引起单点系泊系统载荷先增大后减小;而Pinkster近似法计算得到的二阶波浪力逐渐减下,引起单点载荷逐渐减下。在浅水条件下,Pinkster近似法具有较好的适用性,Newman近似法严重低估了FPSO所受的二阶波浪力;在深水条件下,Newman近似法能满足工程计算的要求;适用两种方法的临界水深/吃水比为1.64。 相似文献
8.
当FPSO服役于目标油田时,将受到风浪流的作用力。其中,风力给FPSO一个恒定的静力,使其偏离原来的位置。风力计算在FPSO系泊系统的分析过程中是非常重要的。设计人员常常参考OCIMF进行风力计算,或者参考API规范得出。OCIMF为针对油轮的计算规范,但使用OCIMF计算FPSO风力及流力的方法,与FPSO的适应性仍需要进一步论证。API规范针对海上浮式系统,其计算风流力的方法使用也非常广泛,其原理为将FPSO上部各个模块风力叠加得出。以FPSO风载荷为研究对象,开展了风洞模型试验,获得了典型FPSO风载荷特性曲线,并将试验结果分别与OCIMF结果和API规范计算结果进行对比分析,最终给出FPSO风力计算方法的建议。本数据可用于FPSO的风力计算,也可为FPSO运动、系泊的设计研究提供参考。 相似文献
9.
10.
11.
The floating production storage and offloading unit (FPSO) is an offshore vessel that produces and stores crude oil prior to tanker transport. Robust prediction of extreme hawser tensions during the FPSO offloading operation is an important safety concern. Excessive hawser tension may occur during certain sea conditions, posing an operational risk. In this paper, the finite element method (FEM) software ANSYS AQWA has been employed to analyze vessel response due to hydrodynamic wave loads, acting on a specific FPSO vessel under actual sea conditions.In some practical situations, it would be useful to improve the accuracy of some statistical predictions based on a certain stochastic random process, given another synchronous highly correlated stochastic process that has been measured for a longer time, than the process of interest. In this paper, the issue of improving extreme value prediction has been addressed. In other words, an efficient transfer of information is necessary between two synchronous, highly correlated stochastic processes. Two such highly correlated FPSO hawser tension processes were simulated in order to test the efficiency of the proposed technique. 相似文献
12.
It is ideal to design the best hull shape for a floating production storage and offloading unit (FPSO) that meets all performance criteria from an engineering point of view. However, in reality, it is difficult to satisfy all the criteria at the same time. If one of the performances cannot meet the criteria, then additional equipment or systems are installed to improve that performance. In this paper, when an FPSO cannot meet the towing stability inherently, we attempt to establish a procedure for determining an auxiliary towing system. Firstly, various systems that can be applied to the FPSO are compared and reviewed to improve the towing stability of the FPSO. Among them, using three active thrusters was chosen as the auxiliary towing system. Improvement of towing stability was verified from a towing model test conducted at the Maritime Research Institute Netherlands (MARIN). However, thruster cavitation was raised as a key problem when using thrusters for a purpose for which they were not intended. A thruster cavitation model test was additionally performed to check the safety of the thrusters. Based on these results, a safe operating range under extreme condition was confirmed by observing the occurrence of thruster cavitation. The predicted maximum unit total thrust of each thruster was compared with the observed safe operating range. Finally, the effectiveness and safety of the auxiliary towing system was verified. 相似文献
13.
14.
A time-domain simulation method based on potential flow model has been developed to investigate the berthing problem between two floating bodies in wave. The boundary value problem is formulated with respect to an earth-fixed coordinate system because the relative positions of the two vessels continuously change during the berthing operation. The classical finite element method is used to solve the Laplace equation in the fluid domain with moving boundary. The linearized free-surface boundary conditions are integrated in time by applying 4th-order Adams–Bashforth–Moulton method. A simple re-mesh algorithm with local and global mesh systems is introduced to update mesh by considering large horizontal movement of the berthing vessel. The developed numerical method is used to investigate the berthing problem between a FPSO and shuttle tanker in waves. The focus is on the wave-induced motion response during the berthing process. The characteristics of the motion responses in berthing operation are examined with various wave frequencies, berthing speeds and wave headings. 相似文献