共查询到20条相似文献，搜索用时 45 毫秒
1.
部分反射直墙前潜堤水动力特性研究 总被引：1，自引：0，他引：1
基于线性势流理论,对部分反射直墙前潜堤的水动力特性进行了理论研究。利用匹配特征函数展开法给出了潜堤透射系数和反射系数的计算方法,计算结果与边界元方法的计算结果一致。利用数值算例分析了潜堤透射系数和反射系数的主要影响因素。增大部分反射直墙的反射系数,将加大潜堤的透射系数。随着潜堤相对宽度或潜堤与直墙之间相对间距的增加,潜堤透射系数和反射系数呈周期性变化,但变化规律相反。 相似文献
2.
M Baba 《Ocean Engineering》1986,13(3)
Among the offshore breakwaters which are increasingly used in shore protection projects, a bevelled block submerged breakwater with 1 on 1.67 seaward slope and a vertical shoreward face is most advantageous, especially from the point of view of optimum wave damping, minimum wave reflection and maximum sand trapping effects. Different computational methods of wave transmission coefficient of this breakwater are examined with laboratory tests. The Goda's method is found to be the simplest and most suitable in the case of the shore protecting submerged breakwater. However, the consideration of wave steepness also, in selecting the constants may yield better results with this method. 相似文献
3.
比例边界有限元法(SBFEM)是一种半解析的数值方法,比完全数值方法具有更高的精度,该方法结合了有限元和边界元的优点,采用相对少的剖分单元就可以得到较高精度的模拟结果。通过改变有限子域内部比例中心的位置,使这种方法可以应用到多种形式浮体在波浪作用下的水动力特性的计算中。同时还给出了各种形式浮体的波浪力及反射、透射系数的数值结果,并与边界元方法(BEM)计算结果和特征函数展开方法得到解析解进行了比较,均吻合良好。研究表明比例边界有限元不仅可以计算矩形的浮体结构,而且对于多种结构形式的浮体都可以计算,这为多种结构形式浮体的水动力分析提供了一个可行的方法。 相似文献
4.
Based on a two-dimensional linear water wave theory, this study develops the boundary element method (BEM) to examine normally incident wave scattering by a fixed, submerged, horizontal, impermeable plate and a submerged permeable breakwater in water of finite depth. Numerical results for the transmission coefficients are also presented. In addition, the numerical technique's accuracy is demonstrated by comparing the numerical results with previously published numerical and experimental ones. According to that comparison, the transmission coefficient relies not only on the submergence of the horizontal impermeable plate and the height of the permeable breakwater, but also on the distance between horizontal plate and permeable breakwater. Results presented herein confirm that the transmission coefficient is minimum for the distance approximately equal to four times the water depth. 相似文献
5.
《Ocean Engineering》1999,26(4):325-341
Based on a two-dimensional linear water wave theory, this study develops the boundary element method (BEM) to examine normally incident wave scattering by a fixed, submerged, horizontal, impermeable plate and a submerged permeable breakwater in water of finite depth. Numerical results for the transmission coefficients are also presented. In addition, the numerical technique's accuracy is demonstrated by comparing the numerical results with previously published numerical and experimental ones. According to that comparison, the transmission coefficient relies not only on the submergence of the horizontal impermeable plate and the height of the permeable breakwater, but also on the distance between horizontal plate and permeable breakwater. Results presented herein confirm that the transmission coefficient is minimum for the distance approximately equal to four times the water depth. 相似文献
6.
波浪在Jarlan型开孔潜堤上的运动 总被引：2，自引：0，他引：2
The wave motion over a submerged Jarlan-type breakwater consisting of a perforated front wall and a solid rear wall was investigated analytically and experimentally. An analytical solution was developed using matched eigenfunction expansions. The analytical solution was confirmed by previously known solutions for single and double submerged solid vertical plates, a multidomain boundary element method solution, and experimental data. The calculated results by the analytical solution showed that compared with double submerged vertical plates, the submerged Jarlan-type perforated breakwater had better wave-absorbing performance and lower wave forces. For engineering designs, the optimum values of the front wall porosity, relative submerged depth of the breakwater, and relative chamber width between front and rear walls were 0.1–0.2, 0.1–0.2, and 0.3–0.4, respectively. Interchanging the perforated front wall and solid rear wall may have no effect on the transmission coefficient. However, the present breakwater with a seaside perforated wall had a lower reflection coefficient. 相似文献
7.
多消浪室局部开孔沉箱防波堤反射特性的迭代解析研究 总被引：1，自引：0，他引：1
基于势流理论，对多消浪室局部开孔沉箱防波堤的反射特性进行解析研究。研究中采用开孔墙处的二次压力损失边界条件，可以直接考虑波高对于开孔墙处能量损失的影响。利用匹配特征函数展开法和迭代方法得到当前问题的解析解。收敛性验证表明，迭代计算和级数解均具有良好的收敛性。该解析解的计算结果与分区边界元的数值计算结果一致，并且与已有的试验结果符合良好。通过算例分析，研究开孔沉箱防波堤反射系数的主要影响因素。结果表明：与单消浪室开孔沉箱防波堤相比，多消浪室开孔沉箱防波堤可以在更宽的波浪频率范围内保持低反射；增大开孔墙的开孔率，有利于降低多消浪室开孔沉箱防波堤的反射系数；当开孔墙的开孔率沿着入射波方向依次递减时，多消浪室开孔沉箱防波堤的反射系数较小。本文所建立的解析模型简单可靠，可用于工程初步设计中分析开孔沉箱防波堤的水动力性能。 相似文献
8.
1.IntroductionGreat efforts have been devoted to the protection of coastal areas over many years by erectingdikes,seawalls,groin systems,and detached breakwaters.The sea walls,jetties,detached breakwa-ters,etc.are traditionally adopted as absorbingfacilit… 相似文献
9.
A parametric experimental study is conducted to compare the reflection and transmission characteristics of submerged hemi-cylindrical and rectangular rigid and water-filled flexible breakwater models. The results show that, for the rigid breakwaters, rectangular models are more effective than hemi-cylindrical ones in terms of reduction of transmitted waves. As for the flexible breakwaters, the hemi-cylindrical models may give better wave reflection than rectangular ones. However, the energy loss induced by the rectangular breakwaters is much larger and more significant to result in an overall better efficiency in terms of reduction in wave transmission. The effects of internal pressure show that the lowest pressurized flexible models considered in this work are the most effective in the reduction of the transmitted wave height. Higher wave reflection, lower wave transmission and higher energy loss are obtained consistently at the lower submergence depth ratio. 相似文献
10.
In this study, a mathematical model has been developed that can compute various hydrodynamic characteristics of a multiple-row curtainwall-pile breakwater. To examine the validity of the developed model, laboratory experiments have been conducted for double- and triple-row breakwaters with various combinations of drafts of curtain walls, porosities between piles, and distances between rows. Comparisons between measurement and prediction show that the mathematical model adequately reproduces most of the important features of the experimental results. As a whole, the transmission coefficient decreases with an increase in relative water depth, whereas the reflection coefficient, normalized run-up and force exhibit an opposite trend in their variations. With fixed values of the draft of the curtain wall and the porosity of lower perforated part of the first row of a double-row breakwater, as these values of the second row increase and decrease, respectively, the transmission coefficient decreases, as expected. On the other hand, their effects on wave reflection, run-up, and wave force change with the relative depth. As for the distance between the rows, the transmission coefficient becomes a maximum when it is about one half of the wave length, suggesting that this condition should be avoided to achieve the advantage of the breakwater in reducing wave transmission. It is shown that for prototype breakwaters, on an average, the transmission coefficient would be smaller than 0.3 for wave periods less than 6.0 s, and it would be about 0.45 even for the wave period of 9.0 s, although there would be a variation depending on the geometry of the breakwater. It is also shown that wave transmission is significantly reduced by multiple-row breakwaters compared with a single-row breakwater, while the difference between double-row and triple-row breakwaters is marginal. Finally, engineering monograms are provided for double-row breakwaters to be used in practical engineering applications of the breakwaters. 相似文献
11.
Numerical prediction of performance of submerged breakwaters 总被引：1，自引：0，他引：1
The results of a numerical model study on the transmission characteristics of a submerged breakwater are presented. Study aimed to determine the effect of depth of submergence, crest width, initial wave conditions and material properties on the transmission characteristics of the submerged breakwater. The results highlight the optimum crest width of the breakwater and optimum clear spacing between two breakwaters. A submerged permeable breakwater with ds/d=0.5, p=0.3 and f=1.0, reduces the transmission coefficient by about 10% than the impermeable breakwater. The results indicates an optimum width ratio of B/d=0.75 for achieving minimum transmission. By restricting the effective width ratio of the series of breakwaters to 0.75, studies were conducted to determine the effect of clear spacing between breakwaters on transmission coefficient, suggesting an optimum clear spacing of w/b=2.00 to obtain Kt below 0.6. 相似文献
12.
Fifteen formulae of wave transmission coefficient for submerged breakwaters obtained during last 3 decades are presented,compared,and analyzed in this paper.The dimensionless parameters mainly involved in this discussion are the relative submerged depth Rc/h,relative wave height Rc/Hi,relative rubble size B/D50,relative breakwater width B/HiL0 and wave breaker index ξ.It indicates that there exist notable differences among the computed results,which mainly originate from the limited experimental conditions and different analytical methods,even though the major tendency keeps similar.It is necessary to conduct more systematic studies to obtain better understanding about the mechanism of wave transmission over submerged breakwaters. 相似文献
13.
淹没矩形防波堤透反射系数特性研究 总被引：2，自引：1，他引：2
采用解析方法研究了斜向入射波作用下淹没矩形防波堤的透反射系数特性.首先利用特征函数展开法导出了绕射势函数的分析解和透反射系数的计算公式,然后利用边界元方法验证了解析解,在此基础上利用解析解分析了若干工况下的防波堤透反射特性.计算结果表明,淹没矩形防波堤截面的宽度、高度和相对位置以及入射角的改变都不同程度影响反射系数和透射系数.在中等深度条件下,对于一定频率的波浪,位置和尺寸适当的淹没矩形堤可以反射大部分斜向入射波.研究结果对设计淹没的矩形防波堤具有重要的参考价值. 相似文献
14.
This paper discusses some previous, and presents some new experimental results on wave transmission over submerged breakwaters. The objective of this study is to evaluate wave transmission coefficient and develop a two-dimensional （2D） model as an improvement to the existing wave transmission coefficient models. Factors which affect wave transmission over stbmerged breakwaters are discussed through a series of laboratory experiments. Basic recommendations for evaluation and design of submerged rubble-monud breakwaters are presented. From the test results, a calculation formula of wave transmission coefficient is proposed. 相似文献
15.
16.
In the present work, the improved version of the meshless singular boundary method(ISBM) is developed for analyzing the performance of bottom standing submerged permeable breakwaters in regular normally incident waves and in the proximity of a vertical wall. Both single and dual prismatic breakwaters of rectangular and trapezoidal forms are examined. The physical problem is cast in terms of the Laplace equation governing an irrotational flow and incompressible fluid motion with appropriate mixed type boundary conditions, and solved numerically using the ISBM. To model the permeability of the breakwaters fully absorbing boundary conditions are assumed. Numerical results are presented in terms of hydrodynamic quantities of the reflection coefficients. These are firstly validated against the results of a multi-domain boundary element method(BEM) developed independently for a previous study. The agreement between the results of the two methods is excellent. The coefficients of reflection are then computed and discussed for a variety of structural conditions including the breakwaters height, width, spacing, and absorbing permeability. Effects of the proximity of the vertical plane wall are also investigated. The breakwater's width is found to have only marginal effects compared with its height. Permeability tends to decrease the minimum reflections. These coefficients show periodic variations with the spacing relative to the wavelength. Trapezoidal breakwaters are found to be more cost-effective than the rectangular breakwaters. Dual breakwater systems are confirmed to perform much better than single structures. 相似文献
17.
In this work, we carried out an asymptotic analysis, up to the second order in a regular expansion, of the interaction of linear long waves with an impermeable, fixed, submerged breakwater composed of wavy surfaces. Below the floating breakwater, there is also a step with a wavy surface. The undulating surfaces are described by sinusoidal profiles. The effects of three different geometric parameters — the amplitude of the wavy surfaces and the submerged length and width of the structure — on the reflection and transmission coefficients are analyzed. The hydrodynamic forces are also determined. The governing equations are expressed in dimensionless form. Using the domain perturbation method, the small wavy surfaces of the breakwater are linearized. The wavy surfaces of the breakwater generate larger values of the reflection coefficient than those obtained for breakwaters with flat surfaces, and the largest values of this coefficient are obtained when the length of the breakwater is of the same order of magnitude as the wavelength. The asymptotic solution is compared with the theoretical solutions that have been reported in the specialized literature and with a numerical solution. The present mathematical model can be used as a practical reference for the selection of the geometric configuration of a submerged floating breakwater under shallow flow conditions. 相似文献
18.
Experimental study of strong reflection of regular water waves over submerged breakwaters in tandem 总被引：3，自引：0，他引：3
A series of laboratory experiments was carried out to investigate the strong reflection of regular water waves over a train of submerged breakwaters. Rectangular and trapezoidal shapes of submerged breakwaters are employed and compared for reflecting capability of incident waves. Measured reflection coefficients of regular waves over impermeable submerged breakwaters are verified by comparing with those of the eigenfunction expansion method. A very good agreement is observed. Reflection coefficients of permeable submerged breakwaters are less than those of impermeable breakwaters. The trapezoidal shape is recommended for a submerged breakwater in terms of reflecting capability and practical application. 相似文献
19.
Long wave reflection from submerged trapezoidal breakwaters 总被引：1，自引：0，他引：1
This study addresses the reflection and transmission of long waves from a trapezoidal breakwater and a series of trapezoidal breakwaters, using the matching method. A systematic shape transfer is derived to determine wave reflection and transmission. The peak Bragg reflection of long waves from a series of trapezoidal breakwaters is shifted toward low frequency. In spite of the spacing between any pair of breakwaters, the top plane width and the arrangement of the series of breakwaters are found to be the two major parameters in designing multiply composite Bragg breakwaters. 相似文献
20.
LI Xue-yan WANG Qing YOU Zai-jin GUO Wei-jun ZHANG Jun-bin ZHAN Chao ZHANG Zhi-chen WANG Li-xue LI Qin 《中国海洋工程》2020,(1):89-98
Comprehensive experimental and numerical studies have been undertaken to investigate wave energy dissipation performance and main influencing factors of a lower arc-plate breakwater. The numerical model, which considers nonlinear interactions between waves and the arc-plate breakwater, has been constructed by using the velocity wave- generating method, the volume of fluid (VOF) method and the finite volume method. The results show that the relative width, relative height and relative submergence of the breakwater are three main influencing factors and have significant influence on wave energy dissipation of the lower arc-plate open breakwater. The transmission coefficient is found to decrease with the increasing relative width, and the minimum transmission coefficient is 0.15 when the relative width is 0.45. The reflection coefficient is found to vary slightly with the relative width, and the maximum reflection coefficient is 0.53 when the relative width is 0.45. The transmission and reflection coefficients are shown to increase with the relative wave height for approximately 85% of the experimental tests when the relative width is 0.19 0.45. The transmission coefficients at relative submergences of 0.04, 0.02 and 0 are clearly shown to be greater than those at relative submergences of 0.02 and 0.04, while the reflection coefficient exhibits the opposite relationship. After the wave interacts with the lower arc-plate breakwater, the wave energy is mainly converted into transmission, reflection and dissipation energies. The wave attenuation performance is clearly weakened for waves with greater heights and longer periods. 相似文献