共查询到20条相似文献，搜索用时 78 毫秒
1.
FSRU在恶劣环境条件下的作业和安全停靠性能与系泊缆张力、靠垫挤压应力、船体6自由度运动等参数有关。针对FSRU码头处海洋环境条件,进行FSRU不同装载状况的模型实验,获得FSRU的6自由度运动及其系泊载荷的动力特性。基于三维辐射和绕射理论,使用Sesam软件进行频域计算,以此为基础在相应海洋环境条件下进行时域耦合分析,获得FSRU 6自由度运动、系泊载荷、靠垫应力等参数的响应时历。结果表明:30%装载、横浪条件下FSRU的运动响应最大,系泊缆张力未达到破断值,靠垫压力超过其压缩60%时的载荷;模型实验对FSRU运动响应和系泊缆张力的预测结果可信,靠垫受力情况需要数值仿真进行辅助研究。 相似文献
2.
参考英国的Kincardine风机采用的新式的Semi-Spar概念,结合spar式基础和半潜式基础的特点,提出了一种新式海上浮式风机平台模型,并基于三维势流理论,利用AQWA软件进行水动力计算,验证新式平台可靠性。分析了在风、浪、流荷载联合作用下,锚链竖向夹角、系缆数量对风机浮式平台运动性能和系泊张力的影响,对系泊系统进行优化,并验证极端工况下的可靠性。结果证明风机平台水平运动和纵摇运动幅值较小,但垂荡幅值略大,而通过减小锚链竖向夹角可以控制平台运动响应幅值,增加系缆数量可以同时减小系泊张力大小。计算结果证明了新型Semi-Spar式海上风机平台可行性,为浮式风机平台及系泊系统的设计提供参考。 相似文献
3.
基于我国南海海域环境条件,对一座深水圆筒型钻井平台设计一套张紧式系泊定位系统,利用SESAM软件对平台运动响应和缆索张力进行分析计算,得到主要运动响应为纵荡、纵摇和垂荡。分别考虑0°和180°的环境载荷方向,对比得到0°方向的缆索张力更大,且6号和7号缆承受了主要的环境力。分析了平台运动的影响因素,认为缆索夹角设定为35°时较优,适度增大系泊缆初始长度和减小两端锚链长度可较为有效地降低系泊缆受力,系泊缆总根数保持12时（4根×3组）为最优方案。根据分析结果对初始系泊方案进行了优化,在风暴工况下系泊缆最大受力减小了约14.8%。钻井作业工况和一根系泊缆破断工况下,系泊缆受力和平台位移均能满足规范要求。 相似文献
4.
基于多体动力分析方法进行FPSO和水下软钢臂系泊系统的运动特性研究。相较于非线性弹簧模拟软钢臂系泊系统或者其他近似模拟方法,多体分析方法可以充分考虑系泊系统具体结构形式及其动力项对FPSO运动性能的影响,更好的预报系统运动响应和系泊力。本文将FPSO和水下钢臂结构模拟成2个具有6自由度的独立结构,两者用系泊链组进行连接。基于三维势流理论应用汇源分布法,首先在频域内进行FPSO的水动力参数分析,进而在时域内对系统进行耦合动力分析。本文重点讨论系泊系统黏性力和二阶波浪力对系统响应的影响,计算结果发现系泊系统黏性力对系泊力有一定影响,而在浅水条件下二阶波浪力的计算对准确预报系统运动及系泊力非常重要。 相似文献
5.
6.
在频域和时域内研究对等分布式系泊和分组式系泊2种系泊模式对Spar平台运动性能的影响,并分析单根系泊缆破断失效后平台运动性能的变化。首先建立Spar平台的三维水动力模型,通过在平台柱体导缆孔处指定预张力、倾角和刚度来模拟系泊系统的影响;然后采用三维势流理论进行浮体水动力计算,获得Spar平台运动响应的传递函数等水动力参数;最后根据实际海况资料,在平台生存工况下,进行Spar平台在完好系泊和单根系泊缆破断失效状态下运动响应的短期预报,并在时域内进行耦合分析,研究平台运动响应和系泊缆张力变化情况。研究结果对Spar平台系泊系统设计和平台设计前期运动性能研究有参考意义。 相似文献
7.
多锚链系泊浮筒非线性漂移运动的时域模拟 总被引：3，自引：0，他引：3
本文对多锚链系泊浮筒漂移运动的非线性效应进行了讨论。在波浪力和锚链系泊力都是非线性的条件下,对浮筒的运动作时域模拟,并把计算单个系泊锚链流体动力作用的Koterayama W.方法推广到多系泊锚链的情形。计算了规则波和波群中系泊浮筒漂移运动的时间历程,讨论了其运动与波高、频差的关系。可以指出,系泊浮筒系统总漂移运动受锚链流体动力的影响很大;在波群中,其幅值主要受波高支配,与频差的关系较小。 相似文献
8.
转塔位置是内转塔式FPSO设计中的重要参数,对风标效应以及运动和系泊力等有重要影响.采用时域分析方法分别计算了10万吨级FPSO在不同转塔位置时百年一遇风、浪、流海洋环境条件作用下的运动响应和系泊力,分析了不同转塔位置对FPSO水动力性能的影响.计算结果与模型实验进行了比较,结果表明,转塔位置的变化对FPSO风标效应、转塔系泊力等影响显著.分析结果对于选择理想的转塔位置具有一定的实际意义. 相似文献
9.
10.
为研究顺应式海洋平台慢漂运动的影响因素,以截断圆柱和漂浮方箱为例进行了不规则波作用下的慢漂运动模型试验。测量了不同系泊刚度条件下的漂浮方箱以及相同系泊刚度条件下的截断圆柱和漂浮方箱在静水中自由衰减运动和在不规则波中的运动响应,并将运动响应分解成一阶波频运动响应和二阶低频运动响应,分析了系泊刚度和浮体形状对浮体运动的影响。通过物理模型试验发现了系泊刚度及浮体形状对顺应式系泊浮体一阶运动标准差和二阶低频运动平均漂移值和标准差的关系。结果表明由于顺应式浮体的固有周期远离波浪谱峰周期时,系泊刚度以及浮体形状对慢漂运动的一阶运动响应影响不大;二阶低频运动相对偏离平衡位置的平均值和标准差均随系泊刚度增大而减小,浮体形状同样对慢漂运动的二阶低频纵荡运动响应影响较大。试验结果为实际海洋工程的外形选择和系泊刚度选择提供数据支持。 相似文献
11.
Air-floating towing beha viors of multi-bucket foundation plat form （MBFP） are investigated with the 1/20-scale model tests and hydrodynamic so ftware MOSES. MOSES numerical model was val idated by test results, and M OSES prototype model of MBFP can eliminate scale effect of model. The influences of towing factors of to wing speed, water depth, freeboard, and w ave direction on air-floating tow ing stability of MBFP were analyzed by model tests and validated MOSES prototype mod el. It is sho wn that the re duction of towing sp eed can effectively d ecrease the to wing force and surge acceleration to improve towing stability. Water depth is another f actor in towing s tability. Obvious shallow water effect will appear in shallow water with sma ll water depth-draft ratio and it w ill disappear gradually and air-floating towing becomes more stable with the increase of water depth. Accelerations of surge, s way and heave are small and they have modest changes when freeboard increases from 0.5 to 2 m. For MBFP, the freeboard is not suggested to be larger than 2 m in following wave. Wave direction has large influence on the towing stability, the surge acceleration and towing force are sensitive to the va riation of wave direction, the surge acceleration and towing force in following wave （0°） and counter wave （180°） are much larger than that in transverse sea （90°and 270°）. 相似文献
12.
针对导管架平台上部组块与火炬臂进行整体拖航的情况,提出考虑拖航累积损伤的火炬臂全寿命疲劳分析流程。采用MOSES和SACS软件建立上部组块带火炬臂整体拖航水动力模型和导管架平台整体有限元模型,计算拖航驳船运动惯性载荷、在位波载荷和在位风载荷引起的火炬臂管节点疲劳损伤,对火炬臂进行全寿命疲劳分析。引入拖航疲劳损伤率系数,量化拖航驳船运动对火炬臂各管节点疲劳损伤的影响。结果表明:拖航工况驳船运动惯性载荷造成的火炬臂疲劳损伤不容忽略,特别是对靠近火炬臂根部的管节点影响显著。因此,在对整体拖航下的火炬臂进行疲劳设计时,应对其进行全寿命疲劳分析。 相似文献
13.
A novel variation of the geophysical technique known as MOSES, for Magnetometric Off-Shore Electrical Sounding, has been developed to map the electrical properties of the sea floor in Aretic regions. The particular target is the permafrost layer under the Beaufort Sea, a layer containing frozen or partially frozen sediment from 100 to 600 m thick underlying shallow sea water, typically 10 to 100 m deep, and several tens of metres of soft sediment. A detailed knowledge of the location and physical properties of the permafrost layer is essential for accurate interpretation of reflection seismic data. The permafrost can contain pockets, regions or layers of gas hydrate. The latter is both a possible resource and a hazard to drilling operations or hydrocarbon production. A local map of the permafrost zone is essential geotechnical information required prior to the construction of an offshore structure or pipeline.The MOSES method is particularly suitable for offshore electrical mapping as it can be made relatively insensitive to the shielding effects of the highly conductive sea water, in sharp contrast to many other electrical techniques. The transmitter is a vertical, long-wire bipole, extending from the sea surface to the sea floor. A commutated current is fed to two large electrodes: one near the sea surface and the other on the sea floor. The return current is through the sea water and the subjacent sediment. The receiver consists of two horizontal orthogonal coils located on the sea floor, and the data are measurements of two components of the magnetic field as a function of frequency and transmitter-receiver horizontal separation.The electrical conductivity of a sample of frozen material is much smaller than that of unfrozen or partially frozen sediment of the same type. Frozen and unfrozen thin layers are often observed sequentially throughout the geological section. The resistivity measured as a function of depth by an electrical logging tool is consequently highly variable. The resulting depth-averaged resistivity, the resistivity resolved by a surface electrical method, is macro-an-isotropic. An experimental design study reveals that both the vertical and horizontal averaged resistivities could be determined in a MOSES sounding without vertical scale distortion.A test of the methodology in very shallow water was conducted in the spring of 1986 at a site, approximate coordinates (70° N, 134.5° W), 85 km north-west of the town of Tuktoyaktuk. The instrumentation was lowered and subsequently recovered through holes in the ice which covers the Beaufort Sea at that time of the year. The transmitter power was obtained from a single lead-acid battery. Transmitter-receiver separations ranged from 10 to 300 m. A rapid increase in sediment resistivity with depth was observed. The higher resistivity values are consistent with those expected for a partially frozen zone. 相似文献
14.
15.
A combined wind and wave energy converter concept, named STC concept was proposed. Model tests were performed in terms of operational and survival modes. Water entry and exit phenomena as well as green water on deck were observed during the survivability model tests. In this paper, a nonlinear numerical model based on a blended station-keeping potential-flow solver with a local impact solution for bottom slamming events and an approximated model for the water shipped on the deck is proposed to simulate these nonlinear phenomena. Physical investigation of the water entry and exit process was firstly carried out and uncertainty analysis of the model test results were performed. Numerical comparisons between the nonlinear solver and model test results are then performed in terms of mean, wave frequency and double wave frequency motion response components. The slamming and green water involved in the water entry process are specially investigated, in terms of the physical evolution and the effects on the dynamic motion responses. The validation work on the occurrence of slamming and water on deck as well as the slamming pressure are performed. 相似文献
16.
This paper describes on the one hand parametric tests on wave overtopping for a steep rubble mound breakwater in Zeebrugge, Belgium. On the other hand the comparison between prototype measurements at the breakwater and their scale reproductions in two laboratories is dealt with. The objective is to gain information on possible scale and model effects for wave overtopping from this comparison. The prototype measurements are described together with the resulting dataset of 11 storms where wave overtopping occurred. Scale models and the laboratory measurements are described into detail mentioning similarities and differences to the prototype. Several model effects are identified and special attention is given to wind effects and to the placement pattern of the armour units, respectively. Monte Carlo simulations have been performed to get an idea about the influence of selected model uncertainties. Finally, scale effects are discussed and the influence of model and scale effects for the performed tests is quantified. Recommendations on how to treat these effects are presented. 相似文献
17.
A model for solving the two-dimensional enhanced Boussinesq equations is presented. The model equations are discretised in space using an unstructured finite element technique. The standard Galerkin method with mixed interpolation is applied. The time discretisation is performed using an explicit three-step Taylor–Galerkin method. The model is extended to the surf and swash zone by inclusion of wave breaking and a moving boundary at the shoreline. Breaking is treated by an existing surface roller model, but a new procedure for the detection of the roller thickness is devised. The model is verified using four test cases and the results are compared with experimental data and results from an existing finite difference Boussinesq model. 相似文献
18.
本文从动力学定律出发,推导了一个线性的、具有下垫面温度耦合的大气环流的统计—动力模式,并用该模式对500hPa高度场及1000hPa温度场作1～30天的平均预报试验。模式的预报结果大大优于惯性预报,但耦合与不耦合的结果差别不大。 相似文献
19.
A thermodynamic model of sea snow-ice cover growth under the influence of heat flows on its upper and lower surfaces is presented. The growing is described with an extended region of phase transition (a two-phase region) with a linear temperature distribution. The temperature of the upper surface is calculated with the use of a heat-balance equation on the basis of determinable meteorological observation data. The comparison of the model results with freezing experimental data is performed. 相似文献
20.
Settlement Analysis for An Embankment Considering Visco-Elasto-Plastic Characteristics 总被引：1，自引：0，他引：1
SHI Jianyong 《中国海洋工程》2000,14(3):349-360
—In the paper.a visco-elasto-plastic constitutive model and a method for determining modelparameters for soft clay are presented.In this model total strain of soft clay is assumed to be divided intothree parts:instantaneous elastic.visco-elastic and visco-plastic.The characteristics of instantaneous andvisco-elastic deformation of soft clay are simulated by Merchant's model.the plastic is by a model withtwo yield surfaces.And related constitutive equation is conducted,A number of stress-controlled triaxialtests are performed to calculated the model parameters The visco-elasto-plastic model is used for analysisof the displacement of an embankment on soft ground by use of three-dimensional finite element method.The predicted settlements agree well with the measured data.It is indicated that the viscous characteristicsshould be taken into account in deformation analysis for soft clay. 相似文献