首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 558 毫秒
1.
受汶川地震扰动影响,彻底关沟泥石流物源丰富,爆发频繁,对下游公路造成严重危害。为查明彻底关沟泥石流发育特征及危害程度,对彻底关沟实地调查,并分析泥石流的形成条件、沟域特征、发展趋势。结果表明,彻底关沟沟道陡峭,雨量丰沛,物源丰富,可参与泥石流的固体物源总量达184.6×104m3,易发程度高。在此基础上,在沟道内选取了4个测流剖面进行计算泥石流运动特征参数。基于上述研究提出了“拦、固、疏、清”治理手段,并结合监测预警的综合防治措施,为类似地质灾害的评价及治理提供参考。  相似文献   

2.
栾川县大南沟泥石流发展处于旺盛期,危害较大,进行治理已迫在眉睫。在对泥石流形成机理、动力特征值计算、工程稳定性评价的基础上,确定了防治工程规模,设计了2座拦砂坝及1220m排导槽的工程防治方案。  相似文献   

3.
泥湾沟为白龙江一级支沟,沟内地质构造发育,固体松散物质丰富,历史上曾爆发多次大规模泥石流灾害,属典型暴雨型黏性泥石流。为更好的对该工程效益进行评价,本次采用FLO-2D模型对其治理前后不同频率的泥石流运动、堆积情况及危险性进行模拟对比。研究结果表明,防治工程的布设能有效拦截流域内松散物质,拦截方量约为3.97×10~4 m~3,回淤反压稳固坡体效果更加明显;泥石流流速控制作用明显,1%降雨频率下到达沟口处流速为2.7m/s,且呈沿拦挡工程逐级减小的趋势。在松散物质及流速得到有效控制的情况下,泥石流冲出方量减少,堆积范围缩小,缩小比例最大达84%。该方法不仅有利于评价泥石流治理效益,也对泥石流治理方案的提出提供有效的数据支持,是值得借鉴与参考的一种评价方法。  相似文献   

4.
本文对都汶公路发育的 4条主要泥石流沟对沟口桥梁的危险性进行了评价,分析了不同频率洪峰流量和泥石流流量及泥石流堆积对工程的冲击力,提出治理工程措施及用于泥石流治理中专门保护公路桥梁的新型结构工程。  相似文献   

5.
《地下水》2017,(5)
针对大夏河高阶地前缘地质灾害普遍发育,危害范围广,威胁对象多的特点,本文对泥石流灾害的形成条件、危害特征进行了探讨,并以崔家沟作为典型泥石流灾害点进行风险评估,提出泥石流工程治理方案,建议在沟内修建拦挡坝稳坡、沟口修建排导堤或排导沟,同时配套相应的植树造林等水保措施,对崔家沟泥石流沟进行全面治理。  相似文献   

6.
叙述了云南省永胜县期纳镇三道河泥石流的发育特征、危害对象,并对该地区泥石流成因进行了分析。阐述了泥石流的形成条件,并对物源区物源条件等局部滑坡崩塌情况进行分析。描述并分析了泥石流诱发因素及形成机制。提出三道河泥石流以"拦固排护结合,以拦排为主"的治理方案,以保护三道河流域居民的生命财产安全。  相似文献   

7.
本文对马槽沟泥石流成因、特征、危害、治理方案、工程设计及治理效益进行了分析研究。该工程建成已运行八年,泥石流危害现已基本解除,治理工程产生了良好的减灾效益、经济效益和社会效益。  相似文献   

8.
通过系统地对城市后山地区主要泥石流沟特征的分析,科学地选取治理工程措施,基本达到有效控制深沟泥石流物源的运移,减轻或消弱其它各沟泥石流危害的防治目标。通过削弱泥石流灾害的发育、发展,从而减轻地质灾害对东川市城区的威胁。  相似文献   

9.
本文对都汶公路发育的4条主要泥石流沟对沟口桥梁的危险性进行了评价,分析了不同频率洪峰流量和泥石流流量及泥石流堆积对工程的冲击力,提出治理工程措施及用于泥石流治理中专门保护公路桥梁的新型结构工程。  相似文献   

10.
昆明市东川城区后山泥石流灾害修复措施   总被引:3,自引:0,他引:3  
莫美仙  张世涛 《云南地质》2006,25(2):242-248
东川城区后山构造发育、地震频繁、山体失稳、地形高差悬殊和雨量集中且暴雨强度大等,是导致本区泥石流频繁而猛烈的根本原因。人类不合理的经济活动则对本区泥石流的发生发展起着重要的加剧、恶化作用。对东川城区后山泥石流的治理必须采用软件和硬件两大措施相结合的综合治理办法,并对治理过的泥石流沟加强管理力度。  相似文献   

11.
Komatiites are mantle-derived ultramafic volcanic rocks. Komatiites have been discovered in several States of India, notably in Karnataka. Studies on the distribution of trace-elements in the komatiites of India are very few. This paper proposes a simple, accurate, precise, rapid, and non-destructive wavelength-dispersive x-ray fluorescence (WDXRF) spectrometric technique for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in komatiites, and discusses the accuracy, precision, limits of detection, x-ray spectral-line interferences, inter-element effects, speed, advantages, and limitations of the technique. The accuracy of the technique is excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Zr, Nb, Ba, Pb, and Th and very good (within 4%) for Y. The precision is also excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th. The limits of detection are: 1 ppm for Sc and V; 2 ppm for Cr, Co, and Ni; 3 ppm for Cu, Zn, Rb, and Sr; 4 ppm for Y and Zr; 6 ppm for Nb; 10 ppm for Ba; 13 ppm for Pb; and 14 ppm for Th. The time taken for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in a batch of 24 samples of komatiites, for a replication of four analyses per sample, by one operator, using a manual WDXRF spectrometer, is only 60 hours.  相似文献   

12.
最新的流行病学研究表明,空气中较高浓度的悬浮细颗粒可能对人类的健康有不利的影响。根据该项研究显示,由于心脏病、慢性呼吸问题和肺功能指标恶化而导致死亡率的升高与细尘粒子有关。这些研究结果已经促使欧盟于1999年4月出台了限制空气中二氧化硫、二氧化氮、氧化氮、铅和颗粒物含量的法案(1999/30/EC),对各项指标包括对可吸入PM10颗粒的浓度提出了新的限制性指标。PM10颗粒是指可以通过预分级器分离采集的气体动力学直径小于10μm的细颗粒。目前研究的兴趣重点逐步偏向PM2.5这些更细微颗粒物,PM2.5这种颗粒物对健康有明显的不利影响。在欧盟指令2008/50/EC中,对PM10和PM2.5都提  相似文献   

13.
本文拟定了一种以熔融法制备样片,用X射线荧光光谱测定硅酸盐类样品中Si、Fe、Al、Tj、Mn、Ca、Mg、K、Na、P等元素的分析方法。在对不同靶材X光管和分光晶体实验对比的基础上,选择了最佳的测量条件。该法具有快速、准确,测量范围广,检测限低,价格便宜等优点。经过近百个各种类型标样或管理样品的分析对比表明,本法不仅适用于硅酸盐类岩石样品的分析,还适用于铁矿、铝土矿、碳酸盐类岩矿样品以及水泥、耐火材料等样品的分析。  相似文献   

14.
This paper reports the first results of a study of 11 isotope systems (3He/4He, 40Ar/36Ar, 34S/32S, 65Cu/63Cu, 62Ni/60Ni, 87Sr/86Sr, 143Nd/144Nd, 206–208Pb/204Pb, Hf–Nd, U–Pb, and Re–Os) in the rocks and ores of the Cu–Ni–PGE deposits of the Norilsk ore district. Almost all the results were obtained at the Center of Isotopic Research of the Karpinskii All-Russia Research Institute of Geology. The use of a number of independent genetic isotopic signatures and comprehensive isotopic knowledge provided a methodic basis for the interpretation of approximately 5000 isotopic analyses of various elements. The presence of materials from two sources, crust and mantle, was detected in the composition of the rocks and ores. The contribution of the crustal source is especially significant in the paleofluids (gas–liquid microinclusions) of the ore-forming medium. Crustal solutions were probably a transport medium during ore formation. Air argon is dominant in the ores, which indicates a connection between the paleofluids and the atmosphere. This suggests intense groundwater circulation during the crystallization of ore minerals. The age of the rocks and ores of the Norilsk deposits was determined. The stage of orebody formation is restricted to a narrow age interval of 250 ± 10 Ma. An isotopic criterion was proposed for the ore-bearing potential of mafic intrusions in the Norilsk–Taimyr region. It includes several interrelated isotopic ratios of various elements: He, Ar, S, and others.  相似文献   

15.
Mining induced subsidence can significantly affect mining costs where major surface facilities and natural environment need to be protected. Overburden grout injection is a technology used to control coal mine subsidence by injecting the mine waste material extracted from the coal back into the inter-burden rock during longwall mining. The flowing slurry is here categorised as a nonlinear viscous cohesive (Bingham plastic) fluid. During longwall mining the grout slurry is pumped into the separated beds of the rock mass through a central vertical borehole, which is drilled deep into the inter-burden rock strata above the coal seam. However, a blockage can occur in the injection system when the slurry velocity falls below a certain critical threshold velocity, indicating a material phase change from cohesive-viscous to cohesive-frictional. In situ field injection tests through boreholes have been simulated at a smaller scale at the CSIRO laboratory in Brisbane by pumping the slurry through a radial disk (gap = 4 mm) from its centre. Laboratory experiments indicate a general, nonlinear, cohesive, viscous, frictional model for shear behaviour of the slurry, in which the material shear parameters are functions of the disk radial distance. Complete dimensional and dimensionless analytical solutions have been developed based on an approach related to Bingham–Herschel–Bulkley fluid mechanics. The derived formulae include relations for minimum pump pressure, local pressure and pressure gradient, wall shear stress, volume rate, velocity and velocity gradient. The theoretical results match the experimental measurements. The experiments covered slurries with maximum particle sizes of 0.5 to 2 mm with about 50% being larger than 100 µm. The viscosities at the various solids concentrations were measured with a standard torsion viscometer. This study differs from the previous research in several distinct aspects, namely, consideration of the variable shear parameters rather than fixed values, inclusion of total nonlinear behaviour, and implementation of a friction function to mimic behaviour of the deposited and consolidating stiff slurry, which can cause a significant pressure rise as a result of the increased shear resistance.  相似文献   

16.
本文介绍样品经四硼酸锂熔融制成玻璃小饼。采用Lachance模式和理论a系数来校正元素间的效应,由3080E型X-射线荧光谱仪和DF-350B数据处理系统完成硅酸盐中十三个项目的测定。  相似文献   

17.
Bellechester, Minnesota, is a small community of approximately 155 residents located on the county line between Goodhue and Wabasha counties in southeast Minnesota's karst region. Bellechester is served by a 21-year-old wastewater treatment facility (WWTF) consisting of three waste-stabilization ponds. On 28 April 1992 six sinkholes were discovered to have drained cell 2 of the WWTF resulting in the loss of approximately 8.7×106 1 of partially treated effluent and about 600 m3 of soil into previously undetected subsurface voids of unknown dimensions. In the week following the collapse, approximately 200 water wells located within a 5-km radius of the WWTF were sampled in an after-the-fact, emergency sampling program. Twelve samples with elevated fecal coliform levels, 18 samples with nitrate-nitrogen greater than the 10 mg/1 standard, and no samples with elevated chlorides were found. However, the elevated levels could not be unambiguously attributed to the WWTF collapse. This is the third WWTF to fail by sinkhole collapse in southeast Minnesota since 1974. All three collapsed lagoons have been located in similar geomorphic and stratigraphic settings. However, at least two lagoons have collapsed in the adjacent area in northeast Iowa, and these lagoons are located at different stratigraphic positions. Twenty-two WWTFs constructed in southeast Minnesota's karst region in the last 25 years have been identified as subject to potential sinkhole collapse. An unknown but significant number of manure storage lagoons, flood control structures, etc., have also been constructed in the karst region and are at risk. Public agencies are beginning to develop plans to deal with the risk associated with existing and future waste lagoons in this environment. The critical hydrogeologic parameters that can be used to prioritize the risk of collapse at existing facilities include: (1) the lithology of the first bedrock beneath each lagoon, (2) the thickness of surficial materials between the lagoon and the bedrock surface, (3) the presence and construction of liners (seepage rate), and (4) the proximity to existing sinkholes.  相似文献   

18.
The Kuskokwim River at Bethel, Alaska, drains a major mercury-antimony metallogenic province in its upper reaches and tributaries. Bethel (population 4000) is situated on the Kuskokwim floodplain and also draws its water supply from wells located in river-deposited sediment. A boring through overbank and floodplain sediment has provided material to establish a baseline datum for sediment-hosted heavy metals. Mercury (total), arsenic, antimony, and selenium contents were determined; aluminum was also determined and used as normalizing factor. The contents of the heavy metals were relatively constant with depth and do not reflect any potential enrichment from upstream contaminant sources.  相似文献   

19.
滇东南锡、银、铅、锌多金属矿床主要分布在个旧、白牛厂、都龙3个矿区,而滇东南较大的3个花岗岩体又分别出露在3个矿区或附近.花岗岩体均形成于燕山晚期,岩石化学、矿物成分相似,富含锡、银、铅、锌、钨、铜等成矿元素.矿床主金属元素组合与岩体之间的距离由远而近出现由锡、钨、(铍、铌、钽)→锡、钨、(铁)、铜、铟→锡、铅、锌、银、铟、(锑)有规律的变化.花岗岩浆是成矿物质来源和成矿热源.岩浆侵入初期使上覆地层隆起产生背斜(凹陷部位成向斜);同时使地层产生一系列裂隙、压性断层或层间断裂;岩浆侵入晚期,这些断层再次活动,表现为张性,岩浆产生的含矿热液沿由其活动所造成的断裂迁移、充填、交代、沉淀而形成矿床.  相似文献   

20.
岩石密度和超高压岩石折返速率   总被引:1,自引:3,他引:1  
在常温常压条件下对中国大陆科学钻CCSD主孔100-3000米岩心样品进行了密度测量,建立了密度连续剖面,并界定了不同超高压岩石的密度值。通过对比高温高压物性实验资料,岩石密度随着退变程度增强而降低,榴辉岩密度变化序列为3.52g/cm3→3.49g/cm3→3.07g/cm3→2.93g/cm3。超高压长英质岩石密度变化序列为3.00g/cm→2.80g/cm3→2.65g/cm3。上述实验资料是讨论不同折返阶段岩石所受浮力的基础,为研究折返速率大小提供了基本参数。本文通过折返板块运动平衡时,上浮力与粘滞力平衡这一关系式,定量研究了大陆俯冲板块的折返速率,认为密度差产生上浮力从而引起折返,温度对板块折返速率的影响最为显著;密度差大小、折返角度、折返板块大小对折返速率也有直接的影响。定量模拟分析表明,在温度高于850℃时,板块的折返速率可以超过100mm/a;当温度降至700℃时,折返速率则低于1.5mm/a。作者认为在折返早期,温度较高,板块快速折返至60-70km榴辉岩相深度;随着传导散热,温度降低,板块以较慢的速率折返至中下地壳。折返速率的估算表明,浮力是板块折返第一阶段(从>100km深部折返至<40km的中下地壳)的主要驱动力。  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号