共查询到20条相似文献，搜索用时 171 毫秒
1.
2.
3.
《西北地质》2016,(2)
梅子垭组是汉阴北部地区出露面积最大的地层,岩性主要为白云母石英片岩、含碳白云母石英片岩、含石榴子石黑云母变斑晶白云母石英片岩等,石榴子石和黑云母变斑晶在该岩层中普遍发育。该岩组构造变形复杂,经历了多期构造活动和变质变形过程。笔者在野外调查的基础上,通过分析研究区石榴子石、黑云母变斑晶的关系,采用石榴子石-黑云母地质温度计,对该区广泛出露的含石榴子石黑云母变斑晶白云母石英片岩进行研究,得到如下结论:研究区存在3期黑云母和石榴子石,石榴子石变斑晶具有明显的生长环带,而黑云母变斑晶没有环带;研究区变质作用的变质温度范围为介于511~572℃,主要为530~560℃;变质压力范围为0.16~0.84GPa,变质相属高绿片岩相。 相似文献
4.
5.
沈坝金矿位于秦岭褶皱系南缘,为化探异常发现的金矿床。矿体赋存在志留系下统的梅子垭组第二岩性段中亚段的岩层内。炭质黑云母变斑晶绢云石英片岩夹含炭变质砂岩为含矿主岩。矿床内综合利用元素低,为单一的金矿床。矿石中的As含量甚微,表明该矿床不同于展布滇黔桂接壤区和西秦岭地区的微细浸染型(卡林型)金矿床。 相似文献
6.
1988年在进行东秦岭南部微细金矿研究时,李文亢、具然弘等于汉阴县鹿鸣乡—罗家湾南剖面原划为志留纪的地层中,发现了早寒武世小壳化石,现简要报导如下: 该区位于南秦岭印支褶皱带南部,濒临扬子准地台,区域上处于牛山复背斜北翼,本身为一倒转向斜—阳坡向斜,剖面位于该向斜的南翼。地层由下而上为(见下图): 1.变质砂岩 2.变质粉砂岩 3.绢云千枚岩 4.板岩 5.绢云石英片岩 6.黑云绢云石英片岩 6.云母石英片岩8.含砂泥质灰岩 8.石榴子石和炭质 10.小壳化石 相似文献
7.
《西北地质》2015,(1)
羊坪湾金矿床地处南秦岭南部逆冲推覆系前缘,在该区域已经发现多个金矿床,显示出巨大的找矿潜力。羊坪湾金矿床矿体主要分布在下志留统梅子垭岩组中,控矿围岩为逆冲推覆剪切带内劈理、裂隙发育的含碳二云母石英片岩及二云母片岩。矿石类型主要为含碳二云母(石英)片岩型。围岩蚀变主要有硅化、黄铁矿化、褐铁矿化、黑云母化和绿泥石化。包裹体中流体成分显示成矿是以H2O-CO2-NaCl为主的热液体系。氢、氧同位素特征表明成矿热液中的水介质是原始地层水,硫同位素特征说明黄铁矿、磁黄铁矿中34S来源于地层。矿源层为志留系梅子垭岩组,燕山期逆冲推覆构造控制本区金矿形成。综合上述方面的研究,建立了羊坪湾金矿床成矿模式。 相似文献
8.
9.
郭奕清 《矿物岩石地球化学通报》1986,(4)
绢英岩矿是近年来发现的一种新型陶瓷原料。矿区主要出露一套中震旦统并轻微变质的浅海相碳酸盐岩和碎屑岩系。自下而上可分为三个岩组:下部为巡检司组,主要由燧石条带灰岩和硅质灰岩组成,其中夹有石英岩、粘土质板岩透镜体;中部为龙家园组,主要由厚层白云岩、自云质灰岩及百英岩组成。上部为高山河组,由巨厚层石英岩和石英砂岩组成。与下伏岩层呈断层接触。矿区地层大体呈近东西向展布,倾向北北东或北东,倾角30—40°。矿区断裂构造发育。 相似文献
10.
<正> 一、区域、矿区及矿床地质概述合川锶矿地处川东褶皱带的西部,华莹山帚状褶皱束的西北分支,沥鼻峡背斜的东北段。背斜长约28km,轴向北东45°～50°,北西翼倾角60°～85°,南东翼倾角30°～40°。背斜轴部出露少量二叠系长兴组(P_2c),三叠系下统飞仙关组(T_1f)。两翼分布有三叠系下统嘉陵江组(T_1j),中统雷口坡组(T_2l),上统须家河组(T_3xj)。矿区位于沥鼻峡背斜北东段的西北翼,地层走向北东50°～55°,呈带状出露(见图1)。 相似文献
11.
S. Viswanathan K. Surya Prakash Rao B. Mahabaleswar 《Journal of the Geological Society of India》2013,82(6):621-627
Komatiites are mantle-derived ultramafic volcanic rocks. Komatiites have been discovered in several States of India, notably in Karnataka. Studies on the distribution of trace-elements in the komatiites of India are very few. This paper proposes a simple, accurate, precise, rapid, and non-destructive wavelength-dispersive x-ray fluorescence (WDXRF) spectrometric technique for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in komatiites, and discusses the accuracy, precision, limits of detection, x-ray spectral-line interferences, inter-element effects, speed, advantages, and limitations of the technique. The accuracy of the technique is excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Zr, Nb, Ba, Pb, and Th and very good (within 4%) for Y. The precision is also excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th. The limits of detection are: 1 ppm for Sc and V; 2 ppm for Cr, Co, and Ni; 3 ppm for Cu, Zn, Rb, and Sr; 4 ppm for Y and Zr; 6 ppm for Nb; 10 ppm for Ba; 13 ppm for Pb; and 14 ppm for Th. The time taken for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in a batch of 24 samples of komatiites, for a replication of four analyses per sample, by one operator, using a manual WDXRF spectrometer, is only 60 hours. 相似文献
12.
E. M. Prasolov S. A. Sergeev B. V. Belyatsky E. S. Bogomolov K. A. Gruzdov I. N. Kapitonov R. Sh. Krymsky V. O. Khalenev 《Geochemistry International》2018,56(1):46-64
This paper reports the first results of a study of 11 isotope systems (3He/4He, 40Ar/36Ar, 34S/32S, 65Cu/63Cu, 62Ni/60Ni, 87Sr/86Sr, 143Nd/144Nd, 206–208Pb/204Pb, Hf–Nd, U–Pb, and Re–Os) in the rocks and ores of the Cu–Ni–PGE deposits of the Norilsk ore district. Almost all the results were obtained at the Center of Isotopic Research of the Karpinskii All-Russia Research Institute of Geology. The use of a number of independent genetic isotopic signatures and comprehensive isotopic knowledge provided a methodic basis for the interpretation of approximately 5000 isotopic analyses of various elements. The presence of materials from two sources, crust and mantle, was detected in the composition of the rocks and ores. The contribution of the crustal source is especially significant in the paleofluids (gas–liquid microinclusions) of the ore-forming medium. Crustal solutions were probably a transport medium during ore formation. Air argon is dominant in the ores, which indicates a connection between the paleofluids and the atmosphere. This suggests intense groundwater circulation during the crystallization of ore minerals. The age of the rocks and ores of the Norilsk deposits was determined. The stage of orebody formation is restricted to a narrow age interval of 250 ± 10 Ma. An isotopic criterion was proposed for the ore-bearing potential of mafic intrusions in the Norilsk–Taimyr region. It includes several interrelated isotopic ratios of various elements: He, Ar, S, and others. 相似文献
13.
14.
奥地利安东帕有限公司 《岩矿测试》2009,28(3):306-306
最新的流行病学研究表明,空气中较高浓度的悬浮细颗粒可能对人类的健康有不利的影响。根据该项研究显示,由于心脏病、慢性呼吸问题和肺功能指标恶化而导致死亡率的升高与细尘粒子有关。这些研究结果已经促使欧盟于1999年4月出台了限制空气中二氧化硫、二氧化氮、氧化氮、铅和颗粒物含量的法案(1999/30/EC),对各项指标包括对可吸入PM10颗粒的浓度提出了新的限制性指标。PM10颗粒是指可以通过预分级器分离采集的气体动力学直径小于10μm的细颗粒。目前研究的兴趣重点逐步偏向PM2.5这些更细微颗粒物,PM2.5这种颗粒物对健康有明显的不利影响。在欧盟指令2008/50/EC中,对PM10和PM2.5都提 相似文献
15.
16.
Mining induced subsidence can significantly affect mining costs where major surface facilities and natural environment need to be protected. Overburden grout injection is a technology used to control coal mine subsidence by injecting the mine waste material extracted from the coal back into the inter-burden rock during longwall mining. The flowing slurry is here categorised as a nonlinear viscous cohesive (Bingham plastic) fluid. During longwall mining the grout slurry is pumped into the separated beds of the rock mass through a central vertical borehole, which is drilled deep into the inter-burden rock strata above the coal seam. However, a blockage can occur in the injection system when the slurry velocity falls below a certain critical threshold velocity, indicating a material phase change from cohesive-viscous to cohesive-frictional. In situ field injection tests through boreholes have been simulated at a smaller scale at the CSIRO laboratory in Brisbane by pumping the slurry through a radial disk (gap = 4 mm) from its centre. Laboratory experiments indicate a general, nonlinear, cohesive, viscous, frictional model for shear behaviour of the slurry, in which the material shear parameters are functions of the disk radial distance. Complete dimensional and dimensionless analytical solutions have been developed based on an approach related to Bingham–Herschel–Bulkley fluid mechanics. The derived formulae include relations for minimum pump pressure, local pressure and pressure gradient, wall shear stress, volume rate, velocity and velocity gradient. The theoretical results match the experimental measurements. The experiments covered slurries with maximum particle sizes of 0.5 to 2 mm with about 50% being larger than 100 µm. The viscosities at the various solids concentrations were measured with a standard torsion viscometer. This study differs from the previous research in several distinct aspects, namely, consideration of the variable shear parameters rather than fixed values, inclusion of total nonlinear behaviour, and implementation of a friction function to mimic behaviour of the deposited and consolidating stiff slurry, which can cause a significant pressure rise as a result of the increased shear resistance. 相似文献
17.
Alexander E. C. Broberg J. S. Kehren A. R. Graziani M. M. Turri W. L. 《Environmental Geology》1993,22(4):353-361
Bellechester, Minnesota, is a small community of approximately 155 residents located on the county line between Goodhue and Wabasha counties in southeast Minnesota's karst region. Bellechester is served by a 21-year-old wastewater treatment facility (WWTF) consisting of three waste-stabilization ponds. On 28 April 1992 six sinkholes were discovered to have drained cell 2 of the WWTF resulting in the loss of approximately 8.7×106 1 of partially treated effluent and about 600 m3 of soil into previously undetected subsurface voids of unknown dimensions. In the week following the collapse, approximately 200 water wells located within a 5-km radius of the WWTF were sampled in an after-the-fact, emergency sampling program. Twelve samples with elevated fecal coliform levels, 18 samples with nitrate-nitrogen greater than the 10 mg/1 standard, and no samples with elevated chlorides were found. However, the elevated levels could not be unambiguously attributed to the WWTF collapse. This is the third WWTF to fail by sinkhole collapse in southeast Minnesota since 1974. All three collapsed lagoons have been located in similar geomorphic and stratigraphic settings. However, at least two lagoons have collapsed in the adjacent area in northeast Iowa, and these lagoons are located at different stratigraphic positions. Twenty-two WWTFs constructed in southeast Minnesota's karst region in the last 25 years have been identified as subject to potential sinkhole collapse. An unknown but significant number of manure storage lagoons, flood control structures, etc., have also been constructed in the karst region and are at risk. Public agencies are beginning to develop plans to deal with the risk associated with existing and future waste lagoons in this environment. The critical hydrogeologic parameters that can be used to prioritize the risk of collapse at existing facilities include: (1) the lithology of the first bedrock beneath each lagoon, (2) the thickness of surficial materials between the lagoon and the bedrock surface, (3) the presence and construction of liners (seepage rate), and (4) the proximity to existing sinkholes. 相似文献
18.
岩石密度和超高压岩石折返速率 总被引：1，自引：3，他引：1
在常温常压条件下对中国大陆科学钻CCSD主孔100-3000米岩心样品进行了密度测量,建立了密度连续剖面,并界定了不同超高压岩石的密度值。通过对比高温高压物性实验资料,岩石密度随着退变程度增强而降低,榴辉岩密度变化序列为3.52g/cm3→3.49g/cm3→3.07g/cm3→2.93g/cm3。超高压长英质岩石密度变化序列为3.00g/cm→2.80g/cm3→2.65g/cm3。上述实验资料是讨论不同折返阶段岩石所受浮力的基础,为研究折返速率大小提供了基本参数。本文通过折返板块运动平衡时,上浮力与粘滞力平衡这一关系式,定量研究了大陆俯冲板块的折返速率,认为密度差产生上浮力从而引起折返,温度对板块折返速率的影响最为显著;密度差大小、折返角度、折返板块大小对折返速率也有直接的影响。定量模拟分析表明,在温度高于850℃时,板块的折返速率可以超过100mm/a;当温度降至700℃时,折返速率则低于1.5mm/a。作者认为在折返早期,温度较高,板块快速折返至60-70km榴辉岩相深度;随着传导散热,温度降低,板块以较慢的速率折返至中下地壳。折返速率的估算表明,浮力是板块折返第一阶段(从>100km深部折返至<40km的中下地壳)的主要驱动力。 相似文献
19.
20.
滇东南锡、银、铅、锌多金属矿床主要分布在个旧、白牛厂、都龙3个矿区,而滇东南较大的3个花岗岩体又分别出露在3个矿区或附近.花岗岩体均形成于燕山晚期,岩石化学、矿物成分相似,富含锡、银、铅、锌、钨、铜等成矿元素.矿床主金属元素组合与岩体之间的距离由远而近出现由锡、钨、(铍、铌、钽)→锡、钨、(铁)、铜、铟→锡、铅、锌、银、铟、(锑)有规律的变化.花岗岩浆是成矿物质来源和成矿热源.岩浆侵入初期使上覆地层隆起产生背斜(凹陷部位成向斜);同时使地层产生一系列裂隙、压性断层或层间断裂;岩浆侵入晚期,这些断层再次活动,表现为张性,岩浆产生的含矿热液沿由其活动所造成的断裂迁移、充填、交代、沉淀而形成矿床. 相似文献