The potential of historic rock avalanches and man-made structures as chlorine-36 production rate calibration sites     

《Quaternary Geochronology》2013

Samples from three medieval rock avalanches from the French (Le Claps, Mont Granier) and Austrian Alps (Dobratsch) and a man-made structure, i.e. the Stephansdom in Vienna, have been analysed for in-situ produced ³⁶Cl by accelerator mass spectrometry (AMS). All four sampling sites of independently known exposure duration turned out to be not appropriate as calibration sites for the determination of the ³⁶Cl-production rate from Ca. Indeed, the determination of short exposure ages for dating rock avalanches and man-made structures by ³⁶Cl is hindered dramatically by inheritance, especially for samples characterized by high ^natCl-concentrations. Generally, there are hints that the theoretical calculation of ³⁶Cl-production from epithermal and thermal neutron-capture on ³⁵Cl is highly underestimated in all existing models, thus, asking for particular precaution if working on high-Cl samples for any project. Hence, this work evidences that potential high inheritance, even for samples reasonably shielded before exhumation, has to be considered especially when dealing with recently exposed surfaces such as glacially polished rocks, alluvial terraces, fault scarps etc.  相似文献   

两种震级标度讨论   总被引：2，自引：0，他引：2  

迟振才  迟天峰 《东北地震研究》2000,(4)

分析论述了我国在测报近震震级和面波震级业务中存在的种种问题,用现行起算函数测算的ML随震中距存在系统偏差,近场偏低,远场偏高;此函数系统建立的方法有不合理之处,它不适于DD-1仪。用现行公式测算的MS与国际上震级水平不一致,总体趋势偏高;在90(距离上震级零点严重失控;用单一水平向记录计算MS是个原则性差误。需要用新的起算函数系统代替R1(()计算ML; 需要用新的公式取代现行公式计算MS。  相似文献   

Calibration of the parameters for a hardening–softening constitutive model using genetic algorithms     

Md. Rokonuzzaman  Toshinori Sakai 《Computers and Geotechnics》2010

The present paper introduces a genetic algorithm-based optimization technique to calibrate a nonlinear strain hardening–softening constitutive model for soils using five material parameters. The efficiency of the proposed technique is analyzed through the use of different GA techniques. The effects of elitism, crossover, and mutation, as well as population size, on the performance of the conventional GAs for this problem are investigated. Micro-genetic algorithms (mGAs) are chosen and tested for different population sizes. The mGAs with a population size of five yields the optimal parameter values after fewer function evaluations and capture the overall simulated or experimental behavior at every point in stress–strain and strain paths in triaxial compression. The proposed calibration technique is validated through comparison with the traditional calibration technique.  相似文献   

A hybrid discrete–finite element model for numerical simulation of geomaterials     

Ali Fakhimi 《Computers and Geotechnics》2009

A hybrid discrete–finite element model is introduced for simulation of mechanical behavior of geomaterials. The soil or rock is modeled as a system of discrete balls that interact through normal and shear springs. The balls can be bonded at the contact points to withstand the applied deviatoric stresses. The important feature of this model is that the confining walls that can be imagined for example as the surrounding membrane or the mold in a physical test are modeled by deformable finite elements. This allows simulation of laboratory test features more realistically compared to the situations where the surrounding walls are rigid. The relationships between micro- and macro-properties are investigated in this paper as well. These relationships and the corresponding curves are helpful tools in calibration of the numerical model for the macroscopic elastic properties.  相似文献   

风云三号C星微波湿温探测仪的定标和验证   总被引：6，自引：0，他引：6       下载免费PDF全文

郭杨  卢乃锰  漆成莉  谷松岩  许健民 《地球物理学报》2015,58(1):20-31

风云三号C星(FY-3C)已经于2013年9月23日发射升空,其上装载的微波湿温探测仪(MWHTS)已于9月30日开机正常工作.MWHTS具有对大气温度和湿度垂直分布进行同步探测的能力.MWHTS为跨轨扫描式微波辐射计,在89~191GHz毫米波段内设置了十五个探测通道,其中包括118.75GHz氧气吸收线附近的8个大气温度探测通道,183.31GHz水汽吸收线附近的5个大气湿度探测通道,以及89GHz和150GHz两个窗区通道.设置在118.75GHz的一组毫米波探测通道是国际上业务卫星首次使用的大气探测通道,这组通道和183.31GHz通道对大气进行联合探测,将获得更加精细的大气温湿度垂直分布数据,为数值预报和气候研究提供丰富信息.为保证MWHTS观测资料的定量应用,对仪器性能和定标精度进行了在轨测试.利用MWHTS在轨正常工作后的三个月数据,对仪器在轨定标的基础数据:冷空和黑体计数值,黑体和仪器温度进行监测分析和质量检验,经过质量检验的在轨定标基础数据,结合发射前真空试验得到的非线性订正项在轨定标生成MWHTS观测亮温数据.评估MWHTS在轨辐射定标结果的精度和偏差特性使用了三种方法:1通过场地定标试验获取大气温湿廓线和地面温度等大气参数信息,结合微波逐线正演辐射传输模式MonoRTM(Monochromatic Radiative Transfer Model)模拟MWHTS的上行微波辐射亮温,与MWHTS实际观测结果进行对比分析;2两个通道特性一致的同类星载被动微波载荷同时观测同一目标,观测亮温的差异主要取决于两个载荷的定标系统偏差.选取美国SNPP上搭载的微波探测仪器ATMS作为MWHTS的参考载荷,基于SNO(simultaneous nadir overpass)技术,对两个仪器的观测亮温进行交叉比对,观测亮温时空匹配及均匀性检验的条件为:观测时间差异小于20min,观测像元中心距离小于3km,观测角度在星下点附近差异小于5°,观测像元周围3×3像元内的亮温标准差小于1K;3基于美国国家环境预测中心的全球数据同化系统GDAS(Global Data Assimilation System)数据,利用快速辐射传输模式CRTM(Community Radiative Transfer Model)对MWHTS各通道亮温进行正演模拟,模拟结果(O)和仪器实际观测的亮温(B)之间的差异记为"O-B",对偏差值"O-B"进行统计特征分析.仪器中心频率的变化、正演模式模拟精度和模式输入廓线自身的误差都会对"O-B"产生影响.但是对于首次使用的探测频点而言(如118.75GHz通道),由于国际上没有同类载荷可以进行交叉比对,借助于正演辐射传输模式计算得到"O-B"偏差的分析结果可以在一定程度上反映仪器整体定标情况.外场地定标试验结果显示除通道14外,其他14个通道的亮温差都在1.3K以内;与同类载荷ATMS的在轨观测进行直接交叉比对表明通道14与ATMS的亮温偏差最大,但中心频点一致的5个水汽探测通道的标准差都小于1K;将MWHTS观测结果和正演辐射传输模式模拟结果即"O-B"进行偏差分析显示,靠近118.75GHz吸收线中心的通道2—6"O-B"标准差小于0.5K,其他通道"O-B"标准差和ATMS相应通道的结果相当;MWHTS观测和模拟偏差随角度变化的研究表明通道1,7~13和15观测结果对角度有一定依赖性.  相似文献   

瞬变电磁传感器阻尼特性的标定研究   总被引：3，自引：2，他引：1       下载免费PDF全文

张爽  刘紫秀  陈曙东 《地球物理学报》2014,57(2):662-670

传统瞬变电磁法（TEM）认为临界阻尼匹配时传感器响应快、无振荡,为最佳匹配方式.本文通过建立基于标定环的TEM系统标定模型,理论证明当略欠阻尼匹配时传感器响应最快、时域畸变最小,为最佳匹配方式.本文采用基于实测数据的背景场剔除方法将一次场和大地响应剔除,通过对不同阻尼状态下标定环早期响应畸变的定量评价,实验证明传感器在略欠阻尼匹配状态下二次场响应畸变最小.本文理论和标定实验均证明,在纯二次场观测方式下,采用略欠阻尼匹配方式能够显著降低早期响应畸变、提高系统浅层探测能力,是浅层探测时传感器最佳匹配方式.  相似文献   

低阻区利用地回路标定航空TEM系统的理论研究   总被引：2，自引：2，他引：0       下载免费PDF全文

张爽  陈曙东  于群 《地球物理学报》2012,55(8):2779-2786

本文针对吊舱式航空TEM系统,建立了基于地回路的系统参数标定模型,并分别计算了自由空间模型响应(TLR)、均匀大地模型响应(TER)、地回路与大地耦合模型响应(TELR和TLER).由于TER响应表现为幅度沿测线不变,据此提出通过增加拟合参数的方法实现系统标定,消除了TER响应对标定的影响.TELR和TLER早期响应具...  相似文献   

An inter-laboratory comparison of cosmogenic 3He and radiogenic 4He in the CRONUS-P pyroxene standard     

《Quaternary Geochronology》2015

This study reports an inter-laboratory comparison of the ³He and ⁴He concentrations measured in the pyroxene material CRONUS-P. This forms part of the CRONUS-Earth and CRONUS-EU programs, which also produced a series of natural reference materials for in situ produced ²⁶Al, ¹⁰Be, ¹⁴C, ²¹Ne and ³⁶Cl.Six laboratories (GFZ Potsdam, Caltech Pasadena, CRPG Nancy, SUERC Glasgow, BGC Berkeley, Lamont New York) participated in this intercomparison experiment, analyzing between 5 and 22 aliquots each. Intra-laboratory results yield ³He concentrations that are consistent with the reported analytical uncertainties, which suggests that ³He is homogeneous within CRONUS-P. The inter-laboratory dataset (66 determinations from the 6 different labs) is characterized by a global weighted mean of (5.02 ± 0.12) × 10⁹ at g⁻¹ with an overdispersion of 5.6% (2σ). ⁴He is characterized by a larger variability than ³He, and by an inter-lab global weighted mean of (3.60 ± 0.18) × 10¹³ at g⁻¹ (2σ) with an overdispersion of 10.4% (2σ).There are, however, some systematic differences between the six laboratories. More precisely, 2 laboratories obtained mean ³He concentrations that are about 6% higher than the clustered other 4 laboratories. This systematic bias is larger than the analytical uncertainty and not related to the CRONUS-P material (see Schaefer et al., 2015). Reasons for these inter-laboratory offsets are difficult to identify but are discussed below. To improve the precision of cosmogenic ³He dating, we suggest that future studies presenting cosmogenic ³He results also report the ³He concentration measured in the CRONUS-P material in the lab(s) used in a given study.  相似文献   

Interlaboratory comparison of cosmogenic 21Ne in quartz     

《Quaternary Geochronology》2015

We performed an interlaboratory comparison study with the aim to determine the accuracy of cosmogenic ²¹Ne measurements in quartz. CREU-1 is a natural quartz standard prepared from amalgamated vein clasts which were crushed, thoroughly mixed, and sieved into 125–250 μm and 250–500 μm size fractions. 50 aliquots of CREU-1 were analyzed by five laboratories employing six different noble gas mass spectrometers. The released gas contained a mixture of 16–30% atmospheric and 70–84% non-atmospheric (predominantly cosmogenic) ²¹Ne, defining a linear array on the ²²Ne/²⁰Ne-²¹Ne/²⁰Ne three isotope diagram with a slope of 1.108 ± 0.014. The internal reproducibility of the measurements is in good agreement with the formal analytical precision for all participating labs. The external reproducibility of the ²¹Ne concentrations between labs, however, is significantly overdispersed with respect to the reported analytical precision. We report an average reference concentration for CREU-1 of 348 ± 10 × 10⁶ at [²¹Ne]/g[SiO₂], and suggest that the 7.1% (2σ) overdispersion of our measurements may be representative of the current accuracy of cosmogenic ²¹Ne in quartz. CREU-1 was tied to CRONUS-A, which is a second reference material prepared from a sample of Antarctic sandstone. We propose a reference value of 320 ± 11 × 10⁶ at/g for CRONUS-A. The CREU-1 and CRONUS-A intercalibration materials may be used to improve the consistency of cosmogenic ²¹Ne to the level of the analytical precision.  相似文献   

Best practice methodology for 14C calibration of marine and mixed terrestrial/marine samples     

《Quaternary Geochronology》2015

There is a lack of detailed guidance in the published literature on how to calibrate ¹⁴C measurements made on marine or mixed marine/terrestrial (primarily human remains) samples. We describe what we consider to be the best approach towards achieving the most accurate calibrated age ranges, using the most appropriate ΔR and percentage marine diet estimates, and associated, realistic error terms on these values. However, this approach will increase the calibrated age range(s) by fully accounting for the variability in both the model and the material. While the discussion is based on examples from the UK and Iceland, the same fundamental arguments can be applied in any geographic location largely devoid of C₄ plants as the high δ¹³C values from such plants can make identification of marine intake difficult to determine.  相似文献