共查询到20条相似文献，搜索用时 31 毫秒
1.
Lei Sun Xiangmei Meng Guanbao Li Guangming Kan Baohua Liu 《Marine Georesources & Geotechnology》2020,38(5):595-603
AbstractThe high-frequency acoustic properties of seafloor sediments are very significant in seafloor study and underwater acoustic study field. In order to measure the sound speed and the attenuation for the small-scale sediment cores more accurately, this study developed a water coupled acoustic laboratory measurement system based on Richardson-Briggs technique. This method used the correlation comparison of waveforms received in sediment core and in identical reference tubes filled with water to measure sound speed and attenuation. The sound speed and attenuation of a clayey silt sediment sample were measured using the water coupled acoustic laboratory measurement system. This frequency dependence of the sound speed and attenuation showed that the clayey silt sediment has a weak positive sound speed dispersion, while the attenuation increases with a strong positive gradient within the measurement frequency range. This study also noted that the measured sound speed ratio match well with the empirical equations from literature. The measured attenuation factor data can fall in the Hamilton’s empirical prediction range. 相似文献
2.
3.
《Oceanic Engineering, IEEE Journal of》2001,26(1):26-53
A 1-km2 area located 2 km off the Florida Panhandle (30°22.6'N; 86°38.7'W) was selected as the site to conduct high-frequency acoustic seafloor penetration, sediment propagation, and bottom scattering experiments. Side scan, multibeam, and normal incidence chirp acoustic surveys as well as subsequent video surveys, diver observations, and vibra coring, indicate a uniform distribution of surficial and subbottom seafloor characteristics within the area. The site, in 18-19 m of water, is characterized by 1-2-m-thick fine-to-medium clean sand and meets the logistic and scientific requirements specified for the acoustic experiments. This paper provides a preliminary summary of the meteorological, oceanographic, and seafloor conditions found during the experiments and describes the important physical and biological processes that control the spatial distribution and temporal changes in these characteristics 相似文献
4.
Tests of models for high-frequency seafloor backscatter 总被引：3，自引：0，他引：3
Jackson D.R. Briggs K.B. Williams K.L. Richardson M.D. 《Oceanic Engineering, IEEE Journal of》1996,21(4):458-470
The interaction of high-frequency sound with the seafloor is inherently a stochastic process. Inversion techniques must, therefore employ good stochastic models for bottom acoustic scattering. An assortment of physical models for bottom backscattering strength is tested by comparison with scattering strength data obtained at 40 kHz at three shallow water sites spanning a range of sediment types from fine silt to coarse sand. These acoustic data are accompanied by sediment physical property data obtained by core sample analysis and in situ probes. In addition, stereo photography was used to measure the power spectrum of bottom relief on centimeter scales. These physical data provided the inputs needed to test the backscatter models, which treat scattering from both the rough sediment-water interface and the sediment volume. For the three sites considered here, the perturbation model for scattering from a slightly rough fluid seafloor performs well. Volume scattering is predicted to be weak except at a site having a layer of methane bubbles 相似文献
5.
6.
一种分层海底反向散射模型 总被引：1，自引：1，他引：0
In order to predict the bottom backscattering strength more accurately, the stratified structure of the seafloor is considered. The seafloor is viewed as an elastic half-space basement covered by a fluid sediment layer with finite thickness. On the basis of calculating acoustic field in the water, the sediment layer, and the basement, four kinds of scattering mechanisms are taken into account, including roughness scattering from the water-sediment interface, volume scattering from the sediment layer, roughness scattering from the sediment-basement interface,and volume scattering from the basement. Then a backscattering model for a stratified seafloor applying to low frequency(0.1–10 kHz) is established. The simulation results show that the roughness scattering from the sediment-basement interface and the volume scattering from the basement are more prominent at relative low frequency(below 1.0 kHz). While with the increase of the frequency, the contribution of them to total bottom scattering gradually becomes weak. And the results ultimately approach to the predictions of the high-frequency(10–100 kHz) bottom scattering model. When the sound speed and attenuation of the shear wave in the basement gradually decrease, the prediction of the model tends to that of the full fluid model, which validates the backscattering model for the stratified seafloor in another aspect. 相似文献
7.
This paper examines the impact that a thin layer of varying density would have on high-frequency reflection, forward loss, and backscattering of acoustic plane waves from the seafloor. A functional form for density stratification was found by examination of several high-resolution density profiles obtained from X-ray computed tomography (CT) scans of seafloor cores. A solution based on these general profiles was used to estimate the reflection coefficient. The influence of the density profile on reflection loss and backscatter was then calculated using the estimated reflection coefficient. Parameter values used in simulations were obtained from the literature or from the CT scans of cores. It was found that inclusion of a density profile adds a strong frequency dependence to estimates of the reflection coefficient and forward loss. The largest effect on total scattering strength is near normal incidence where returns are dominated by interface scattering. The effect of the density profile on the strength of acoustic returns suggests that care should be taken when using high-frequency systems for measuring sediment properties, especially near normal incidence 相似文献
8.
为研究小尺度海底沉积物样品的声衰减特性,作者提出了用声学探针测量海底沉积物声波幅值的新方法,对沉积物样品扰动小,两个测量点的距离可小于波长,为海底沉积物微观声衰减测量提供了新手段。作者用小于波长的间隔逐点测量了沉积物的压缩波幅值,数据分析表明沿沉积物柱状样全长的声衰减满足指数衰减模型。目前主要用同轴差距衰减测量法获得海底沉积物声衰减数据,但该方法不能辨识声衰减模型,因此不同海区的测量结果难以建立联系。对此作者又提出用声吸收系数反演的幅值比与声衰减系数反演的R值(两种幅值比的比值)作评价依据,分析了垂直轴差距衰减测量法获得的南海海底沉积物声衰减测量数据,发现部分沉积物样品声衰减的R值远大于1,其声衰减不满足指数衰减模型。在声衰减满足指数衰减模型的条件下,用Hamilton的声衰减和频率经验公式预报的南海沉积物声衰减比与作者用声学探针测量海底沉积物所得的声衰减比对比,通过对R值分析得出Hamilton的声衰减和频率经验公式可以预报南海沉积物声衰减比的范围。作者提出的声学探针测量海底沉积物声衰减的方法的优点是既能获得声衰减数据又能辨识声衰减模型,不同海区测量的沉积物声衰减比可用R值建立联系。 相似文献
9.
10.
海底浅表层（小于1 m）沉积物的物理性质,如粒度、孔隙度、密度等是海洋沉积学研究和海洋工程地质分析的重要内容,目前主要基于有限的海底取样或原位测试获取这些沉积物的物理性质。浅地层剖面是基于声学信号（频率几千赫兹）在沉积物中的传播得到可反映沉积地层结构的数据,其中的一些声学参数,如海底反射系数、波阻抗等与沉积物物理性质密切相关。如何充分而有效地利用浅地层剖面资料,反演得到剖面覆盖区海底浅表层沉积物的物理性质参数,极具科学意义和应用价值,且基于声学属性反演沉积物物理性质是当前研究的热点。为此,本文基于渤海LD16-3CEPA至LD10-1PAPD路由段的浅地层剖面数据和海底表层沉积物的实测物理参数,利用Biot-Stoll模型建立研究区海底反射系数和沉积物物理性质之间的关系,并基于浅地层剖面数据计算得到的海底反射系数,反演了研究区海底浅表层沉积物的孔隙度、密度、平均粒径等物理性质参数。其中反演的孔隙度、密度、平均粒径与实测孔隙度、密度、平均粒径基本相符,偏差度基本都在20%的偏差范围内,表明该反演方法在该区的应用是可行的。 相似文献
11.
Jingqiang Wang Baohua Liu Guangming Kan Zhiwen Sun Xiangmei Meng 《Marine Georesources & Geotechnology》2018,36(5):515-521
The mechanical structure, the function modules, the working principles, and a sea trial of the newly developed ballast in situ sediment acoustic measurement system are reported in this study. The system relies on its own weight to insert transducers into seafloor sediments and can accurately measure the penetration depth using a specially designed mechanism. The system comprises of an underwater position monitoring and working status judgment module and has two operation modes: self-contained measurement and real-time visualization. The designed maximum working water depth of the system is 3,000?m, and the maximum measured depth of seafloor sediment is 0.8?m. The system has one transmitting transducer with the transmitting frequency band of 20–35?kHz and three receiving transducers. The in situ acoustic measurement system was tested at 15 stations in the northern South China Sea, and repeated measurements in seawater demonstrated good working performance. Comparison with predictions from empirical equations indicated that the measured speed of sound and attenuation fell within the predicted range and that the in situ measured data were reliable. 相似文献
12.
The capabilities and diversity of subsurface sediment sensors lags significantly from what is available for the water column, thereby limiting progress in understanding time-dependent seabed exchange and high-frequency acoustics. To help redress this imbalance, a new instrument, the autonomous sediment profiler (ASP), is described herein. ASP consists of a four-electrode, Wenner-type resistivity probe and a thermistor that log data at 0.1-cm vertical intervals over a 58-cm vertical profile. To avoid resampling the same spot on the seafloor, the probes are moved horizontally within a 20 times 100-cm-2 area in one of three preselected patterns. Memory and power capacities permit sampling at hourly intervals for up to 3-mo duration. The system was tested in a laboratory tank and shown to be able to resolve high-frequency sediment consolidation, as well as changes in sediment roughness. In a field test off the southern coast of France, the system collected resistivity and temperature data at hourly intervals for 16 d. Coupled with environmental data collected on waves, currents, and suspended sediment, the ASP is shown to be useful for understanding temporal evolution of subsurface sediment porosity, although no large depositional or erosional events occurred during the deployment. Following a rapid decrease in bottom-water temperature, the evolution of the subsurface temperature field was consistent with the 1-D thermal diffusion equation coupled with advection in the upper 3-4 cm. Collectively, the laboratory and field tests yielded promising results on time-dependent seabed change. 相似文献
13.
声波在海底界面的反射和透射是海底散射、海底混响、海底目标探测的重要问题。利用Biot多孔介质声传播理论对声波在水-多孔海底界面上的反射和透射进行了分析,具体给出反射声波的反射系数,3种透射声波的透射系数以及声能透射系数随入射波入射角和频率(10~40 kHz)的变化关系,分析了各种透射波对透射声能的贡献。多孔海底介质参数分别采用Stoll和Chotiros给出的2组参数进行理论计算。 相似文献
14.
The sediment–water interface is usually marked by an increase in acoustic impedance and is therefore displayed in a seismic
section as a positive polarity reflection. Here, we use the term “seabed phase reversal” to describe areas of seafloor which
are instead expressed as a negative polarity reflection in seismic data. We describe in detail a number of examples of seafloor
phase reversals and use a simple one-dimensional geophysical model to test the hypothesis that they are the result of the
presence of gas within the seafloor sediment. Our examples are all related to seismically imaged mud volcanoes located within
the South Caspian Sea. Sections of phase-reversed seafloor at the summit area of these volcanoes have been mapped to reveal
the existence of seafloor mud pools (salses) and recently erupted mud flows which show a strong similarity to smaller-scale
features at onshore volcanoes in Azerbaijan. Synthetic geophysical modelling indicates that under the physical conditions
likely to occur when the seabed sediment is gas-bearing, the seafloor will be expressed as a strong negative polarity reflection.
Unlike other indicators of seafloor gas, such as pockmarks, which merely record the transient expulsion of fluids from sedimentary
basins, seafloor phase reversals indicate the presence of gas in marine sediment at the time of survey acquisition. They therefore
are of significance to engineering and site survey operations as well as the identification of biological communities and
gas flux calculations. 相似文献
15.
16.
本文通过对南海海底沉积物样品的声学物理参数和沉积粒度特征统计分析，发现了高、低含砂量沉积物的声学物理特征存在明显差异，建立了海底沉积物的含砂量与压缩波速度、孔隙度、含水量和密度等经验公式，分析了含砂量变化与沉积物的体积压缩模量和密度变化的关系，从声速理论基础上阐明了含砂量变化引起沉积物压缩波速度变化的内在原因是含砂量变化引起了体积压缩模量和密度发生了变化，说明了含砂量增大引起沉积物压缩波速度增大的内在原因是含砂量增大引起了体积压缩模量变化量大于密度变化量，从而在数据统计和理论分析结合基础上，论证了含砂量是影响海底沉积物压缩波速度的重要因素之一。这一研究对声学方法反演海底沉积物粒度参数和沉积物类型、地声参数转换模型的建立，以及对水声反演海底和海底资源勘探等方面都具有重要理论意义和应用价值。 相似文献
17.
T.F. Sutherland J. Galloway R. Loschiavo C.D. Levings R. Hare 《Estuarine, Coastal and Shelf Science》2007,75(4):447-458
Both acoustic and sediment surveys were carried out in the Broughton Archipelago, British Columbia, in order to map a former aquaculture site and calibrate acoustic surveys with georeferenced sediment properties. The acoustic surveys included EM3000 Multibeam (including backscatter) and QTC VIEW™ (Series IV) technologies, while the geotechnical survey entailed Van Veen grab sampling of surface sediments and associated analyses. The two acoustic technologies were consistent in their ability to identify distinct regions of seafloor characterized by rock outcrops, consolidated substrates, or gel-mud depositional fields. Both multibeam backscatter data and QTC VIEW™ number-coded classifications were extracted across a range of circular areas located at each georeferenced sampling station (radii: 2, 3, 4, 5, 8, 12, 16, 20 m). Statistical correlations were observed between backscatter and certain geotechnical properties, such as sediment porosity, sediment grain size fractions (<2 μm, silt content), and particulate sulfur concentration. The areal resolution of backscatter extraction was explored in terms of determining a sensitive calibration technique between backscatter and sediment properties. In general the highest r2 values between backscatter and sediment variables were observed across extraction radii between 8 and 20 m. Such groundtruthing techniques could be used to interpolate seafloor characteristics between sampling stations and provide a steering tool for sampling designs associated with benthic monitoring programs. 相似文献
18.
Evangelos Alevizos Mirjam Snellen Dick Simons Kerstin Siemes Jens Greinert 《Marine Geophysical Researches》2018,39(1-2):289-306
This study applies three classification methods exploiting the angular dependence of acoustic seafloor backscatter along with high resolution sub-bottom profiling for seafloor sediment characterization in the Eckernförde Bay, Baltic Sea Germany. This area is well suited for acoustic backscatter studies due to its shallowness, its smooth bathymetry and the presence of a wide range of sediment types. Backscatter data were acquired using a Seabeam1180 (180 kHz) multibeam echosounder and sub-bottom profiler data were recorded using a SES-2000 parametric sonar transmitting 6 and 12 kHz. The high density of seafloor soundings allowed extracting backscatter layers for five beam angles over a large part of the surveyed area. A Bayesian probability method was employed for sediment classification based on the backscatter variability at a single incidence angle, whereas Maximum Likelihood Classification (MLC) and Principal Components Analysis (PCA) were applied to the multi-angle layers. The Bayesian approach was used for identifying the optimum number of acoustic classes because cluster validation is carried out prior to class assignment and class outputs are ordinal categorical values. The method is based on the principle that backscatter values from a single incidence angle express a normal distribution for a particular sediment type. The resulting Bayesian classes were well correlated to median grain sizes and the percentage of coarse material. The MLC method uses angular response information from five layers of training areas extracted from the Bayesian classification map. The subsequent PCA analysis is based on the transformation of these five layers into two principal components that comprise most of the data variability. These principal components were clustered in five classes after running an external cluster validation test. In general both methods MLC and PCA, separated the various sediment types effectively, showing good agreement (kappa >0.7) with the Bayesian approach which also correlates well with ground truth data (r2?>?0.7). In addition, sub-bottom data were used in conjunction with the Bayesian classification results to characterize acoustic classes with respect to their geological and stratigraphic interpretation. The joined interpretation of seafloor and sub-seafloor data sets proved to be an efficient approach for a better understanding of seafloor backscatter patchiness and to discriminate acoustically similar classes in different geological/bathymetric settings. 相似文献
19.
Liang Yuanbo Lu Bo Huang Shaojian Li Tinghuan Yang Weiguang Wen Yaolin 《Marine Georesources & Geotechnology》2013,31(3-4):189-201
Abstract The possibility of seafloor failure under external loadings on a gently sloping continental shelf is controlled, to a large extent, by the geotechnical characters of subbottom sediments (e.g., shear strength, compressibility, and liquefaction potential) and structural factors (e.g., sedimentary stratification). By means of undis‐turbing coring, in‐situ acoustic measurement, and subbottom profiling, the authors conducted an investigation into the seafloor instabilities and possibilities of sediment slope failure within the continental shelf off the Pearl River mouth, which is one of the most important areas for offshore development in the northern South China Sea. Based on in‐situ and laboratory measurements and tests for sediment physical properties, static and dynamic behavior, and acoustic characteristics, the analyses indicate: (1) subbottom sediments that originated from terrigenous clay during the Pleistocene are compact and overconsolidated, and the mean sound velocity in such sediments is relatively high; (2) the maximum vertical bearing capacity of subbottom sediments is efficiently conservative on the safe side for dead loads of light structures, and the trench walls are stable enough while trenching to a depth of about 2 m below the seafloor under still water; and (3) it is quite improbable that the subbottom sediments liquefy under earthquake (M ≤ 6) or storm wave loading. 相似文献
20.
介绍了最新研制的基于液压驱动贯入的自容式海底沉积声学原位测量系统及其在南黄海中部海底沉积声学调查中的应用。该系统可以实现对海底沉积物声速和声衰减系数进行原位测量,通过液压驱动装置将四根声学探杆匀速贯入到海底沉积物中,减少了对沉积物的扰动,可按照预设的工作参数在海底全自动工作,无需甲板上人员实时控制,采集的声波信号自容式存储于存储单元。系统工作水深为500 m,测量深度为1 m,测量频率为30 kHz,采样频率为10 MHz。使用该系统在南黄海中部获得了40个站位不同类型沉积物的声学特性原位测量数据,并使用CTD剖面仪对该系统声速测量进行了标定,相对误差均小于0.5%,表明该系统测量数据准确、可靠。 相似文献