共查询到20条相似文献，搜索用时 196 毫秒
1.
针对传统圆筒型FPSO垂荡运动剧烈的特点,提出一种带有垂荡抑制结构的圆筒型FPSO。采用1∶77.8的缩尺比制作模型,进行垂荡纵摇衰减试验,得到带有不同垂荡抑制结构模型的固有周期和无因次阻尼系数,进而选取最优的垂荡抑制结构型式。之后计算并对比传统圆筒型FPSO和新型圆筒型FPSO垂荡纵摇运动的固有周期和幅频响应函数。在此基础上,结合我国南海海洋环境条件,设计新型圆筒型FPSO的系泊系统,计算分析自存工况下的耦合动力响应,并与传统圆筒型FPSO进行对比。结果表明,文中提出的垂荡抑制结构可以有效增大系统垂荡纵摇运动的固有周期,改善运动性能,提高系泊的安全性。 相似文献
2.
针对圆筒型海上储油装置FPSO垂荡运动性能较差、无法安装干式井口的问题,设计了带延伸筒体与矩形阻尼结构的圆筒型FPSO,根据延伸筒体与矩形阻尼结构是否通海分为两种型式。建立水动力计算模型,比较分析不同延伸筒体和阻尼结构型式对FPSO水动力性能的影响。针对南海作业海域,设计了悬链式系泊系统,基于JONSWAP波浪谱对FPSO的运动进行时域预报,并对系泊系统进行校核。分析结果表明:通海型FPSO垂荡固有周期显著提升,可以错开南海百年一遇谱峰周期,通海型FPSO满足钻井、安装干式井口的运动响应要求,系泊系统系缆张力满足规范要求。 相似文献
3.
基于我国南海海域环境条件,对一座深水圆筒型钻井平台设计一套张紧式系泊定位系统,利用SESAM软件对平台运动响应和缆索张力进行分析计算,得到主要运动响应为纵荡、纵摇和垂荡。分别考虑0°和180°的环境载荷方向,对比得到0°方向的缆索张力更大,且6号和7号缆承受了主要的环境力。分析了平台运动的影响因素,认为缆索夹角设定为35°时较优,适度增大系泊缆初始长度和减小两端锚链长度可较为有效地降低系泊缆受力,系泊缆总根数保持12时（4根×3组）为最优方案。根据分析结果对初始系泊方案进行了优化,在风暴工况下系泊缆最大受力减小了约14.8%。钻井作业工况和一根系泊缆破断工况下,系泊缆受力和平台位移均能满足规范要求。 相似文献
4.
《中国海洋大学学报(自然科学版)》2021,(11)
基于10 MW级大型风机,采用钢筋混凝土结构,进行了半潜浮式风机平台的概念设计,采用SESAM建立平台的数值模型,对立柱间距、立柱倾角及立柱直径对该半潜平台完整稳性的影响规律进行了重点研究并对平台进行优化,对优化后半潜平台的破舱稳性、综合许用重心高度及固有周期进行了验证。结果表明:以上因素以不同的方式影响平台完整稳性,而增加立柱倾角在钢筋混凝土用量和排水量等方面更具优势,优化后的平台完整稳性、破舱稳性、综合许用重心高度及运动周期均满足设计规范要求。 相似文献
5.
6.
针对1 000 m水深作业的新型圆筒型浮式生产储卸油系统（FPSO）,选择多点系泊FPSO和穿梭油轮串靠外输方案,分析串靠方案在中国南海的可行性。FPSO和穿梭油轮作业时两者之间相互影响的研究较为重要,通过ANSYS-AQWA建立水动力耦合分析模型,基于多浮体水动力学方法进行时域耦合仿真模拟。在FPSO作业海况下,分析了串靠外输时系泊锚链及系泊大缆的张力特性和两浮体的运动响应,对大缆的长度和刚度参数变化进行了分析。结果表明：串靠外输方案满足新型圆筒型FPSO的作业环境。随着系泊大缆长度增加,其张力最值逐渐减小,FPSO和穿梭油轮的最小间距逐渐增大。两浮体最小距离稳定在83 m左右。随着系泊大缆刚度增加,其张力最值增大,相比于大缆长度,大缆刚度对耦合系统的影响较弱。 相似文献
7.
埕岛油田海底管线在位稳定性的计算分析 总被引：1，自引：0，他引：1
埕岛油田主要分布粉土和淤泥质软土2类典型的海床.通过建立海床与其上裸置管线相互作用的有限元计算模型,对埕岛油田2类典型海床上裸置管线的在位稳定性进行了数值计算分析,并与现行常用的DNV(挪威船级社)管道设计方法的计算结果进行了对比.分析表明,对于埕岛油田粉土海床上裸置管线的在位稳定性分析,数值计算结果与DNV简化分析方法的结果较为一致;对于埕岛油田淤泥质软土海床上裸置管线的在位稳定性分析,DNV简化分析得到的裸置管线的在位稳定性一般高于相应的数值计算结果. 相似文献
8.
针对圆筒型海上储油装置FPSO,研究其不同类型阻尼结构的阻尼性能,以便有效减小此类结构的垂荡运动。提出U型和倒U型两种不同的圆筒型FPSO阻尼结构型式,采用CFD方法模拟浮体的强迫运动,计算分析阻尼结构的阻尼特性,对比了传统垂荡板结构、U型阻尼结构、倒U型阻尼结构的阻尼性能,详细分析阻尼结构的不同参数包括高度、筒体间距、开孔情况等三个因素对于阻尼特性的影响,基于CFD方法,分析了不同阻尼结构阻尼形成的机理。计算分析表明,倒U型阻尼性能最好,U型和倒U型阻尼结构与筒体间距增大后阻尼增大,阻尼结构高度增加或开孔增加后阻尼降低。 相似文献
9.
FPSO系统在深海海洋油气资源开发中扮演着重要的角色,而深水FPSO系统水下立管管路较长,立管整体重量较大,立管在水流作用下产生的涡激振动也较强,这些将给FPSO主船体带来严重的稳性、强度及疲劳问题。鉴于此,深海FPSO系统在油气资源开发过程中,须在水下一定深度设置若干水下软管支撑浮体,用以支撑来自深海海底的管线,减轻深水立管对FPSO的负载作用。随着深海资源开发的深入发展,传统水下软管支撑浮体作为FPSO系统的关键装备已经无法满足深海开采的需求,寻求大型化、深海化、生命周期长久化的新型水下立管支撑平台迫在眉睫,设计简便快捷、低风险的安装方法成为其开发过程中的重点和难点。详细描述了水下软管支撑浮体的产生及其发展历程,针对深海开发的需求提出了新型立管支撑平台的新概念,着重对新概念下下水安装更便捷的耐压立管支撑平台设计原理及其下水安装方式展开了分析,最后对水下软管支撑浮体和新型立管支撑平台的关键技术进行了总结,并提出了需进一步解决的问题。 相似文献
10.
坐底式平台沉浮稳性研究与计算 总被引：3，自引：0，他引：3
坐底式平台的沉浮稳性与它的作业性能密切相关。随着平台作业水深的不断加大,现有平台的沉浮稳性为操作者、设计者及船检部门所重视。文中分析了现有规范对沉浮稳性的衡准,介绍了计算沉浮稳性的程序框图及计算实例。对提高沉浮作业工况的安全性,给出了一些建议,供平台设计和操作者参考。 相似文献
11.
12.
探讨了壳寡糖及全乙酰壳寡糖的制备方法,通过正交实验考察了原料、温度、时间对降解产物的影响.制备了八种寡糖（八乙酰壳二糖、十一乙酰壳三糖、十四乙酰壳四糖和十七乙酰壳五糖,以及N,N′-二乙酰壳二糖、N,N′,N″-三乙酰壳三糖、N,N′,N″,N′′′四乙酰壳四糖和N,N′,N″,N′′′,N′′′′-五乙酰壳五糖）,并通过IR、NMR及MS等确定了其化学结构. 相似文献
13.
14.
Coastal and estuarine habitat mapping, using LIDAR height and intensity and multi-spectral imagery 总被引：3，自引：1，他引：2
Guillem Chust Ibon Galparsoro ngel Borja Javier Franco Adolfo Uriarte 《Estuarine, Coastal and Shelf Science》2008,78(4):633-643
The airborne laser scanning LIDAR (LIght Detection And Ranging) provides high-resolution Digital Terrain Models (DTM) that have been applied recently to the characterization, quantification and monitoring of coastal environments. This study assesses the contribution of LIDAR altimetry and intensity data, topographically-derived features (slope and aspect), and multi-spectral imagery (three visible and a near-infrared band), to map coastal habitats in the Bidasoa estuary and its adjacent coastal area (Basque Country, northern Spain). The performance of high-resolution data sources was individually and jointly tested, with the maximum likelihood algorithm classifier in a rocky shore and a wetland zone; thus, including some of the most extended Cantabrian Sea littoral habitats, within the Bay of Biscay. The results show that reliability of coastal habitat classification was more enhanced with LIDAR-based DTM, compared with the other data sources: slope, aspect, intensity or near-infrared band. The addition of the DTM, to the three visible bands, produced gains of between 10% and 27% in the agreement measures, between the mapped and validation data (i.e. mean producer's and user's accuracy) for the two test sites. Raw LIDAR intensity images are only of limited value here, since they appeared heterogeneous and speckled. However, the enhanced Lee smoothing filter, applied to the LIDAR intensity, improved the overall accuracy measurements of the habitat classification, especially in the wetland zone; here, there were gains up to 7.9% in mean producer's and 11.6% in mean user's accuracy. This suggests that LIDAR can be useful for habitat mapping, when few data sources are available. The synergy between the LIDAR data, with multi-spectral bands, produced high accurate classifications (mean producer's accuracy: 92% for the 16 rocky habitats and 88% for the 11 wetland habitats). Fusion of the data enabled discrimination of intertidal communities, such as Corallina elongata, barnacles (Chthamalus spp.), and stands of Spartina alterniflora and Phragmites australis, which presented misclassification when conventional visible bands were used alone. All of these results were corroborated by the kappa coefficient of agreement. The high classification accuracy found here, selecting data sources, highlights the value of integrating LIDAR data with multi-spectral imagery for habitat mapping in the intertidal complex fringe. 相似文献
15.
Adsorption and desorption of proteins and polyamino acids by clay minerals and marine sediments 总被引：1，自引：0，他引：1
The adsorption and desorption of proteins and polyamino acids on illite, montmorillonite, goethite, and marine sediments was investigated. Three 14C-labeled hydrophilic proteins, Rubisco from C. reinhardtii, and GroEL and GroES from genetically modified Escherichia coli, were synthesized and purified for this study. The proteins were strongly and rapidly adsorbed by the clay minerals and marine sediments, and much of the adsorbed protein was not readily desorbed. Sodium dodecyl sulfate (SDS) extraction and separation by SDS-polyacrylamide gel electrophoresis (PAGE) and sucrose density gradients showed that Rubisco and GroEL were adsorbed on illite and sediments in their original forms. The apparent adsorption partition coefficients of the proteins were on the order of 102 l/kg on illite, 103–104 l/kg on goethite and montmorillonite, and 200 and 75 l/kg on Skan Bay and Resurrection Bay (Alaska) sediments, respectively. These partition coefficients are sufficiently large to permit sedimentary protein preservation via an adsorptive mechanism. Generally, basic polyamino acids had greater adsorption partition coefficients than acidic polyamino acids. Molecular size did not affect the electrostatic interaction between polyamino acids and mineral surfaces. Adsorption of bovine serum albumin (BSA) and negatively charged polyamino acids inhibited Rubisco adsorption, while positively charged cytochrome c and polyamino acids increased Rubisco adsorption. These results indicate that electrostatic interactions dominated in protein adsorption. 相似文献
18.
19.