共查询到20条相似文献，搜索用时 31 毫秒
1.
CFD, system-based and EFD study of ship dynamic instability events: Surf-riding, periodic motion, and broaching 总被引：1，自引：0，他引：1
Hamid Sadat-Hosseini Frederick Stern Naoya Umeda Shinya Yamamura 《Ocean Engineering》2011,38(1):88-110
CFD and system-based simulation are used to predict broaching, surf-riding, and periodic motion for the ONR Tumblehome model, including captive and free model test validation studies. CFD shows close agreement with EFD for calm water resistance, static heel (except for sway force and yaw moment), and static drift (except for roll moment). CFD predictions of static heel in following waves also compare well with EFD except for surge force, sway force, and pitch angle. Froude-Krylov calculations of wave-induced surge force in following waves provides good agreement for high Froude number, but significantly overestimates for Froude number less than 0.2. On the other hand, CFD successfully reproduces the reduction of the wave-induced surge force near Froude number 0.2, probably because CFD can capture the 3D wave pattern. CFD free model simulations are performed for several speeds and headings and validated for the first time for surf-riding, broaching, and periodic motions. System-based simulations are carried out based on inputs from EFD, CFD, and Froude-Krylov for a dense grid of speeds and headings to predict the instability map, which were found to produce fairly similar results. 相似文献
2.
The most common method of reducing roll motion of ship-shaped floating systems is the use of bilge keel which act as damping elements. The estimation of the damping introduced by bilge keel is still largely based on empirical methods. The present work adopts the CFD approach to the estimation of roll damping, both without and with bilge keel and validates the results with experiments conducted in a wave flume. Specifically, free oscillation tests are conducted at model scale to obtain roll damping, both by experiments and CFD simulation and reasonably good comparisons are obtained. The experiments also include PIV study of the flow field and attempt has been made to correlate the measured flow field with that obtained by CFD. The CFD methodology has the potential to determine rationally the size and orientation of bilge keels in design with reasonably accurate estimate of the additional roll damping that it provides to ship's roll motion. 相似文献
3.
This paper has shown a numerical motion simulation method which can be employed to study on parametric rolling of ships in a seaway. The method takes account of the main nonlinear terms in the rolling equation which stabilize parametric rolling, including the nonlinear shape of the righting arm curve, nonlinear damping and cross coupling among all 6 degrees of freedom. For the heave, pitch, sway and yaw motions, the method uses response amplitude operators determined by means of the strip method, whereas the roll and surge motions of the ship are simulated, using nonlinear motion equations coupled with the other 4 degrees of freedom. For computing righting arms in seaways, Grim's effective wave concept is used. Using these transfer functions of effective wave together with the heave and pitch transfer functions, the mean ship immersion, its trim and the effective regular wave height are computed for every time step during the simulation. The righting arm is interpolated from tables, computed before starting the simulation, depending on these three quantities and the heel angle. The nonlinear damping moment and the effect of bilge keels are also taken into account. The numerical simulation tool has shown to be able to model the basic mechanism of parametric rolling motions. Some main characteristics of parametric rolling of ships in a seaway can be good reproduced by means of the method. Comprehensive parametric analyses on parametric rolling amplitude in regular waves have been carried out, with that the complicated parametric rolling phenomena can be understood better. 相似文献
4.
A horizontal, circular cylinder fitted with one bilge keel is forced to rotate harmonically around its axis. The bilge keel load and hull pressure distribution are investigated. A fully submerged condition (infinite fluid), and three partly-submerged conditions are considered. A two-dimensional numerical study is performed, and the results are validated against recently published experimental data by van’t Veer et al. [30]. In addition, comparisons for mass and drag coefficients are also made with experimental data for plate in infinite fluid (Keulegan and Carpenter [8]), and wall-mounted plate (Sarpkaya and O’Keefe [9]) in oscillatory flow.A Navier–Stokes solver based on the Finite Volume Method is adopted for solving laminar flow of incompressible water. The free-surface condition is linearized by neglecting the nonlinear free-surface terms and the influence of viscous stresses in the free surface zone, while the body-boundary condition is exact. This simplified modeling of the problem required the mesh to be fine only around the bilge keels, leading to a total number of cells around N ≃ 1 ×104, which reduced computational cost significantly.The influence of draft and amplitude of oscillations on the bilge keel force and hull pressure distribution are considered. The bilge keel force is presented in terms of non-dimensional drag and mass coefficients including higher harmonic components. The numerical results are also compared with the industry standard empirical method for calculation of roll damping proposed by Ikeda et al. [4]. In general, a good agreement between the results of the present numerical method and the experimental data is obtained and the differences with those predicted by the empirical method are addressed. 相似文献
5.
The roll damping characteristics of three models of a 3-ton class fishing vessel representing the bare hull, hull with bilge keels, and hull with bilge keels and a central wing are investigated by the free roll decay tests in calm water and also in uniform head waves in a towing tank. Speed and roll initial angle and OG (distance between the centers of gravity and roll) are varied to check their dependence on roll damping. The experimental results are compared with the numerical results of mathematical modeling by the energy method and the energy dissipation patterns are also compared for these three models. The bilge keel contributes significantly to the increment of the roll damping for zero speed but as speed increases, the lift generated by the central wing contributes significantly to the roll damping increase. In addition, it is shown that the roll damping is more or less influenced by the regular head waves. 相似文献
6.
Computations of self-propulsion free to sink and trim and of motions in head waves of the KRISO Container Ship (KCS) model 总被引：2，自引：0，他引：2
Two computations of the KCS model with motions are presented. Self-propulsion in model scale free to sink and trim are studied with the rotating discretized propeller from the Hamburg Model Basin (HSVA) at Fr = 0.26. This case is particularly complex to simulate due to the close proximity of the propeller to the rudder. The second case involves pitch and heave in regular head waves. Computations were performed with CFDShip-Iowa version 4.5, a RANS/DES CFD code designed for ship hydrodynamics. The self-propulsion computations were carried out following the procedure described in Carrica et al. [1], in which a speed controller is used to find the propeller rotational speed that results in the specified ship velocity. The rate of revolutions n, sinkage, trim, thrust and torque coefficients KT, KQ and resistance coefficient CT(SP) are thus obtained. Comparisons between CFD and EFD show that the rate of revolutions n, thrust and torque coefficients KT and KQ have higher prediction accuracies than sinkage and trim. For the simulation of pitch and heave in head waves, the geometry includes KCS hull and rudder under three conditions with two Froude numbers and three wave length and amplitude combinations. 0th and 1st harmonic amplitudes and 1st harmonic phase are computed for total resistance coefficient CT, heave motion z and pitch angle θ. Comparisons between CFD and EFD show that pitch and heave are much better predicted than the resistance. In both cases comparisons with simulations by other authors presented at the G2010 CFD Workshop [2] using different CFD methodologies are included. 相似文献
7.
For the non-negligible roll-coupling effect on ship maneuvering motion, a system-based method is used to investigate 4-DOF ship maneuvering motion in calm water for the ONR tumblehome model. A 4-DOF MMG model is employed to describe ship maneuvering motion including surge, sway, roll, and yaw. Simulations of circular motion test, static drift and heel tests are performed by solving the Reynolds-averaged Navier-Stokes (RANS) equations, after a convergence study quantifying the necessary grid spacing and time step to resolve the flow field adequately. The local flow field is analyzed for the selected cases, and the global hydrodynamic forces acting on the ship model are compared with the available experiment data. Hydrodynamic derivatives relating to sway velocity, yaw rate, and heel angle are computed from the computed force/moment data using least square method, showing good agreement with those obtained from EFD data overall. In order to investigate further the validity of these derivatives, turning circle and zigzag tests are simulated by using the 4-DOF MMG model with these derivatives. The trajectories and the time histories of the kinematic variables show satisfactory agreement with the data of free-running model tests, indicating that the system-based method coupled with CFD simulation has promising capability to predict the 4-DOF ship maneuvering motion for the unconventional vessel. 相似文献
8.
Prediction potential of the parametric rolling behaviour of a post-panamax containership 总被引：1，自引：0，他引：1
K.J. Spyrou I. Tigkas G. Scanferla N. Pallikaropoulos N. Themelis 《Ocean Engineering》2008,35(11-12):1235-1244
A systematic investigation on the prediction of parametric rolling exhibited by a post-panamax containership is described, on the basis of several techniques. Analytical formulae that appear in current industrial guidelines are evaluated in a step-by-step process against various numerical predictions. The method of continuation of nonlinear dynamics is introduced in order to expedite the identification of the instability boundary and the prediction of steady amplitudes of roll oscillation. A well-known panel code is shown to be capable of reproducing parametric roll growth. 相似文献
9.
The present paper describes an investigation on the relevance of parametric resonance for a typical fishing vessel in head seas. Results for different Froude numbers are discussed based on experimental, numerical and analytical studies.The first region of resonance is investigated. Distinct wave amplitudes are considered. Some intense resonances are found to occur. The paper compares the experimental results with non-linear time simulations of the roll motion. Very good agreement is found, even when large motions take place.Finally, in order to analyze the experimental/numerical results, analytic consideration is given to distinct parameters affecting the dynamic process of roll amplification. The influence of heave, pitch, wave passage effect, speed and roll restoring characteristics are discussed. 相似文献
10.
Since the most severe roll motion occurs at resonance (known as synchronous rolling), the best way of reducing it is to increase the damping. The most common means of doing so is by the installation of bilge keels. If more control is required, both anti-roll tanks and fins are used. Tanks have the advantage of being able to function when the ship is not underway. The use of tanks with liquid free surfaces for reducing roll motion of ships is an old idea. Many researchers have studied the design of anti-roll tanks. However, most of the past effort has concentrated on studying the performance of anti-roll tanks in damping the roll motion of the ship. Little attention has been paid to the fluid motion inside the tank itself. Another important issue is the tank tuning. Proper tuning of the anti-roll tank, to match the ship's natural frequency, is very important in reducing the roll motion. This paper concentrates on the most familiar type, which is the U-tube passive tank as a mechanical absorber of roll motion. A detailed study, covering tank damping, mass, location relative to the ship CG, and tuning, is presented. New suggestions and observations are stated concerning tank damping and tuning. 相似文献
11.
This paper presents bilge keel loads and hull pressure measurements carried out on a rotating cylinder in a free surface water basin. A flat plate bilge keel and one more complex shaped bilge keel were studied to investigate the geometry effect. The draft of the cylinder was varied to study the effect of the vicinity of the free surface on the bilge keel loads and hull pressures. The rotation axis of the cylinder was fixed to define a pure roll experiment (one degree of freedom).The cylinder was subject to forced oscillations of varying amplitude leading to a KC range of 0.3–16. Using Fourier analysis the first three harmonic coefficients representing the normal bilge keel load were derived. The first harmonic drag and inertia coefficients are in good agreement to existing experimental data obtained for wall bounded flat plates fitted in a U-shaped water tunnel as reported by Sarpkaya and O’Keefe (1996). New insight is gained by the fact that the addition of higher harmonic contributions is essential to capture the time varying bilge keel normal force.The pressure measurements next to the bilge keel are compared to measurements reported by Ikeda et al. (1979). Similar findings are obtained, showing that the pressure on the hull in front of the moving bilge keel is KC independent while the vortex system in the wake of the bilge keel leads to KC dependent hull pressure distributions. The hull pressure jump over the bilge keel correlates well to the force coefficient on the bilge keel. The complex nature of the vortex induced hull pressures is manifested. The empirically derived hull pressure distribution by Ikeda et al. (1979) for the time instant of maximum velocity is shown to correlate reasonably well to the measured data with some conservatism in the absolute value.Although a cylinder is very different from a ship-shaped section, the experiments provide essential insight into the physics associated with roll damping and into the factors that should be included in a roll damping prediction method. 相似文献
12.
The dynamic stability of fishing vessels in longitudinal regular waves is investigated, both analytically and experimentally. In particular, the influence of stern shape on the parametric stability of fishing vessels is studied. Vessels TS and RS have very similar main characteristics, but their sterns are different. Although their linear responses are comparable, both analytical and experimental investigations indicate substantial differences in their dynamic stability in longitudinal regular waves. Strong resonances are found for the vessel with the deep transom. The analytical method takes into consideration the effects of the heave and pitch motions and wave passage and shows good agreement with experimental results. Stability limits are obtained for different conditions and are used as an aid in the discussion of the results obtained in the tests when relevant parameters are changed, such as wave amplitude and frequency, metacentric height and roll damping moment. 相似文献
13.
This study considers the coupling effects of ship motion and sloshing. The linear ship motion is solved using an impulse-response-function (IRF) method, while the nonlinear sloshing flow is simulated using a finite-difference method. The IRF method requires the frequency-domain solution prior to conversion to time domain, but the computational effort is much less than that of direct time-domain approaches. The developed scheme is verified by comparing the motion RAOs between the frequency-domain solution and the solution obtained by the IRF method. Furthermore, a soft-spring concept and linear roll damping are implemented to predict more realistic motions of surge, sway, yaw, and roll. For the simulation of sloshing flow in liquid tanks, a physics-based numerical approach adopted by Kim [2001. Numerical simulation of sloshing flows with impact load. Applied Ocean Research 23, 53–62] and Kim et al. [2004. Numerical study on slosh-induced impact pressures on three-dimensional prismatic tanks. Applied Ocean Research 26, 213–226] is applied. In particular, the present method focuses on the simulation of the global motion of sloshing flow, ignoring some local phenomena. The sloshing-induced forces and moments are added to wave-excitation forces and moments, and then the corresponding body motion is obtained. The developed schemes are applied for two problems: the sway motion of a box-type barge with rectangular tanks and the roll motion of a modified S175 hull with rectangular anti-rolling tank. Motion RAOs are compared with existing results, showing fair agreement. It is found that the nonlinearity of sloshing flow is very important in coupling analysis. Due to the nonlinearity of sloshing flow, ship motion shows a strong sensitivity to wave slope. 相似文献
14.
Increasing propulsion efficiency, safety, comfort and operability are of the great importance, especially for small ships operating on windy sites like the North Sea and the Baltic Sea. Seakeeping performance of ships and offshore structures can be analysed by different methods and the one that is becoming increasingly important is CFD RANS. The recent development of simulation techniques together with rising HPC accessibility enables performance of advanced seakeeping simulations for ships in a full scale. The paper presents CFD seakeeping analysis for a case study vessel in two variants: V-shaped bulbous bow hull form (as built) and innovative hull form (X-bow type). The study presents the influence of redesigning the ship on selected seakeeping aspects. The advanced CFD model, with the application of overset mesh technique, was described in detail. Selected numerical results were validated on the basis of experimental testing in a towing tank and showed good agreement. The approach demonstrated here of performing the CFD seakeeping simulations for the analysis of ship performance in a full scale and close to real loading conditions has direct application to the design process as well as in determination of optimal operational parameters of any ship. 相似文献
15.
The best way of reducing roll motion is by increasing roll damping. Bilge keels are the most common devices for increasing roll damping. If more control is required, anti-roll tanks and fins are used. Tanks have the advantage of being able to function when the ship is not underway. Our objective is to develop design procedures for passive tanks for roll reduction in rough seas. This paper focuses on the design of passive U-tube tanks. The tank-liquid equation of motion is integrated simultaneously with the six-degree-of-freedom (6DOF) equations of the ship motion. The coupled set of equations is solved by using the Large Amplitude Motion Program ‘LAMP’, which is a three-dimensional time-domain simulation of the motion of ships in waves. The unstabilized and stabilized roll motions of a S60-70 ship with forward speed and beam waves have been analyzed. For high-amplitude waves, the unstabilized roll angle exhibits typical nonlinear phenomena: a shift in the resonance frequency, multi-valued responses, and jumps. The performance of a S60-70 ship with a passive tank is investigated in various sea states with different encounter wave directions. It is found that passive anti-roll tanks tuned in the linear or nonlinear ranges are very effective in reducing the roll motion in the nonlinear range. The effect of the tank damping, frequency, and mass on the tank performance is studied. Also, it is found that passive anti-roll tanks are very effective in reducing the roll motion for ships having a pitch frequency that is nearly twice the roll frequency in sea states 5 and 6. 相似文献
17.
The use of wavelet transforms is explored to investigate the nonlinear dynamical characteristics of ship roll and coupled heave-roll motion. The harmonic character, double period character and chaotic character are observed via a time–frequency window of the wavelet transform. Typical wave parameters in different stability regions are considered. Features such as restoring rolling, divergence rolling, steady state and chaotic responses of ship roll are obtained as well. The investigation in this paper not only highlights the feasibility of using wavelet transforms in the analysis of nonlinear dynamic characteristics of ship rolling in waves, but also shows how it could enhance the analysis abilities. 相似文献
18.
The present paper describes a mathematical model in which the fluid motion inside a U-tank is nonlinearly coupled to the heave, roll and pitch motions of the ship. The main purpose of the investigation is centred on the control of roll motion in the case of parametric resonance in longitudinal waves. A transom stern small vessel, known to be quite prone to parametric amplification, is employed in the study. Four tank designs are employed in order to study the influence of tank mass, tank natural frequency and tank internal damping on the control of parametric rolling at different head seas conditions. Additionally, the influence of the vertical position of the tank is also investigated. The main results are presented in the form of limits of stability, with encounter frequency and wave amplitudes as parameters. Distinct dynamical characteristics are discussed and conclusions are drawn on the relevant parameters for the efficient control of the roll amplifications in head seas. 相似文献
19.
Computational fluid dynamics, CFD, is becoming an essential tool in the prediction of the hydrodynamic efforts and flow characteristics of underwater vehicles for manoeuvring studies. However, when applied to the manoeuvrability of autonomous underwater vehicles, AUVs, most studies have focused on the determination of static coefficients without considering the effects of the vehicle control surface deflection. This paper analyses the hydrodynamic efforts generated on an AUV considering the combined effects of the control surface deflection and the angle of attack using CFD software based on the Reynolds-averaged Navier–Stokes formulations. The CFD simulations are also independently conducted for the AUV bare hull and control surface to better identify their individual and interference efforts and to validate the simulations by comparing the experimental results obtained in a towing tank. Several simulations of the bare hull case were conducted to select the k–ω SST turbulent model with the viscosity approach that best predicts its hydrodynamic efforts. Mesh sensitivity analyses were conducted for all simulations. For the flow around the control surfaces, the CFD results were analysed according to two different methodologies, standard and nonlinear. The nonlinear regression methodology provides better results than the standard methodology does for predicting the stall at the control surface. The flow simulations have shown that the occurrence of the control surface stall depends on a linear relationship between the angle of attack and the control surface deflection. This type of information can be used in designing the vehicle's autopilot system. 相似文献
20.
This documentation presents the parametric identification modeling of ship maneuvering motion with integral sample structure for identification (ISSI) and Euler sample structure for identification (ESSI) based on least square support vector machines (LS-SVM), where ISSI is used for the construction of in–out sample pairs. By using Mariner Class Vessel, the sample dataset are obtained from 15°/15° zigzag maneuvering simulation based on Abkowitz model. By analyzing the simulation data including rudder angle, surge velocity, sway velocity, yaw rate and so forth, the hydrodynamic derivatives in Abkowitz model are all identified. The validation of the proposed identification algorithm is verified by the high precisions of the identified hydrodynamic derivatives and maneuvering prediction results. The comparison is also conducted between the proposed ISSI and the conventional Euler sample structure for identification (ESSI), and the experimental results shows that ISSI is much more appropriate for parametric identification modeling of ship maneuvering motion. 相似文献