共查询到20条相似文献，搜索用时 24 毫秒
1.
提出了一种新的基于信号子空间分解技术的3 D地震资料高分辨率处理方法.利用信号子空间分解技术,不仅可以分离3 D地震资料中的信号和噪声,而且可以进一步根据地震同相轴的倾角不同,将混合信号进行分解得到单个同相轴信号.通过丢弃噪声子空间,只对不同信号子空间重构的信号利用谱白化技术进行高分辨率处理,然后累加所有处理结果,从而达到既提高地震资料的分辨率,又提高地震资料信噪比的目的.对合成资料和实际地震资料的处理结果表明,此法具有好的应用前景. 相似文献
2.
当测区噪声很强,采用组合震源工作仍然不能满足信噪比要求时,为进一步提高地震勘探信噪比,引入能形成定向地震波的相控震源.针对水平层状介质模型,对组合震源、相控震源地震进行了数值模拟,并定量计算了采用4,8,15,20单元的组合与相控震源地震数据的信噪比,同组合地震相比,相控地震使来自不同反射层的反射波信号的信噪比平均提高了154～990 dB.结果表明,相控震源地震得到的反射波信号信噪比高于组合地震,并且随着激震器数目增加,相控震源合成地震记录中的反射波地震数据信噪比明显提高. 相似文献
3.
Englacial and subglacial water flow at Skálafellsjökull,Iceland derived from ground penetrating radar,in situ Glacsweb probe and borehole water level measurements 
下载免费PDF全文
下载免费PDF全文 We reconstruct englacial and subglacial drainage at Skálafellsjökull, Iceland, using ground penetrating radar (GPR) common offset surveys, borehole studies and Glacsweb probe data. We find that englacial water is not stored within the glacier (water content ~0–0.3%). Instead, the glacier is mostly impermeable and meltwater is able to pass quickly through the main body of the glacier via crevasses and moulins. Once at the glacier bed, water is stored within a thin (1 m) layer of debris‐rich basal ice (2% water content) and the till. The hydraulic potential mapped across the survey area indicates that when water pressures are high (most of the year), water flows parallel to the margin, and emerges 3 km down glacier at an outlet tongue. GPR data indicates that these flow pathways may have formed a series of braided channels. We show that this glacier has a very low water‐storage capacity, but an efficient englacial drainage network for transferring water to the glacier bed and, therefore, it has the potential to respond rapidly to changes in melt‐water inputs. © 2015 The Authors. Earth Surface Processes and Landforms published by John Wiley & Sons Ltd. 相似文献
4.
《地震研究进展（英文）》2021,1(3):100008
In the presence of background noise, arrival times picked from a surface microseismic data set usually include a number of false picks that can lead to uncertainty in location estimation. To eliminate false picks and improve the accuracy of location estimates, we develop an association algorithm termed RANSAC-based Arrival Time Event Clustering (RATEC) that clusters picked arrival times into event groups based on random sampling and fitting moveout curves that approximate hyperbolas. Arrival times far from the fitted hyperbolas are classified as false picks and removed from the data set prior to location estimation. Simulations of synthetic data for a 1-D linear array show that RATEC is robust under different noise conditions and generally applicable to various types of subsurface structures. By generalizing the underlying moveout model, RATEC is extended to the case of a 2-D surface monitoring array. The effectiveness of event location for the 2-D case is demonstrated using a data set collected by the 5200-element dense Long Beach array. The obtained results suggest that RATEC is effective in removing false picks and hence can be used for phase association before location estimates. 相似文献
5.
C. Schmelzbach F. ScherbaumJ. Tronicke P. Dietrich 《Journal of Applied Geophysics》2011,75(4):615-630
Enhancing the resolution and accuracy of surface ground-penetrating radar (GPR) reflection data by inverse filtering to recover a zero-phased band-limited reflectivity image requires a deconvolution technique that takes the mixed-phase character of the embedded wavelet into account. In contrast, standard stochastic deconvolution techniques assume that the wavelet is minimum phase and, hence, often meet with limited success when applied to GPR data. We present a new general-purpose blind deconvolution algorithm for mixed-phase wavelet estimation and deconvolution that (1) uses the parametrization of a mixed-phase wavelet as the convolution of the wavelet's minimum-phase equivalent with a dispersive all-pass filter, (2) includes prior information about the wavelet to be estimated in a Bayesian framework, and (3) relies on the assumption of a sparse reflectivity. Solving the normal equations using the data autocorrelation function provides an inverse filter that optimally removes the minimum-phase equivalent of the wavelet from the data, which leaves traces with a balanced amplitude spectrum but distorted phase. To compensate for the remaining phase errors, we invert in the frequency domain for an all-pass filter thereby taking advantage of the fact that the action of the all-pass filter is exclusively contained in its phase spectrum. A key element of our algorithm and a novelty in blind deconvolution is the inclusion of prior information that allows resolving ambiguities in polarity and timing that cannot be resolved using the sparseness measure alone. We employ a global inversion approach for non-linear optimization to find the all-pass filter phase values for each signal frequency. We tested the robustness and reliability of our algorithm on synthetic data with different wavelets, 1-D reflectivity models of different complexity, varying levels of added noise, and different types of prior information. When applied to realistic synthetic 2-D data and 2-D field data, we obtain images with increased temporal resolution compared to the results of standard processing. 相似文献
6.
7.
Methods that employ arrays of emitters are potentially useful in improving weak or ambiguous signals in ground penetrating radar (GPR) prospecting. As in the seismic case, the electromagnetic responses from the subsurface can be obtained by employing true composite sources or synthesized from single emitter responses that are acquired with variable offset, both possibilities leading to similar results. In this article, the synthetic emitter-array method is examined as a way of improving GPR signals. Modeling of transmitted wave-fronts is carried out to analyze how the targets can be illuminated so that the reflected signals are effectively reinforced. The method is applied to different targets. A methodology that simultaneously increases the signal to noise ratio and the lateral coherence of the events is examined in order to facilitate the interpretation of the GPR data. Finally, the synthetic emitter-array method is successfully applied in a case study to determine the width and depth of mud walls at the Palo Blanco archaeological site in Argentina. 相似文献
8.
Chih-Sung ChenYih Jeng 《Journal of Applied Geophysics》2011,75(1):113-123
An alternative data processing procedure is proposed in this paper for the purpose of enhancing the signal/noise (S/N) ratio of ground penetrating radar (GPR) data. The processing methodology is achieved by performing the logarithmic transform in conjunction with the ensemble empirical mode decomposition (EEMD), a new nonlinear data analysis method in signal processing. The synthetic model study and field example indicate that the logarithmic transform is effective in alleviating the attenuation problem. Additionally, the spectrogram obtained from Hilbert-Huang transform (HHT) shows that the decomposition sensitivity of the EEMD method is greatly improved with the aid of the logarithmic transform. This new method allows us to extract the signal components from noisy GPR data efficiently. The success of this study suggests a possible nonlinear analysis application in future GPR investigation, particularly in the filter design and gain correction. 相似文献
9.
10.
T. D. L. Irvine‐Fynn B. J. Moorman J. L. M. Williams F. S. A. Walter 《地球表面变化过程与地形》2006,31(7):892-909
In recent years, ground‐penetrating radar (GPR) has been increasingly used for characterization of subglacial and englacial environments at polythermal glaciers. The geophysical method is able to exploit the dielectric difference between water, air, sediment and ice, allowing delineation of subsurface hydrological, thermal and structural conditions. More recent GPR research has endeavoured to examine temporal change in glaciers, in particular the distribution of the cold ice zone at polythermal glaciers. However, the exact nature of temporal change that can be identified using GPR has not been fully examined. This research presents the results of three GPR surveys conducted over the course of a summer ablation season at a polythermal glacier in the Canadian Arctic. A total of approximately 30 km of GPR profiles were collected in 2002 repeatedly covering the lower 2 km of Stagnation Glacier, Bylot Island (72°58′ N 78°22′ W). Comparison between profiles indicated changes in the radar signature, including increased noise, appearance and disappearance of englacial reflections, and signal attenuation in the latter survey. Further, an area of chaotic returns in up‐glacier locations, which was interpreted to be a wet temperate ice zone, showed marked recession over the course of the ablation season. Combining all the temporal changes that were detected by GPR, results indicate that a polythermal glacier may exhibit strongly seasonal changes in hydrological and thermal characteristics throughout the ice body, including the drainage of 17 000 m3 of temporarily stored intra‐glacial meltwater. It is also proposed that the liquid water content in the temperate ice zone of polythermal glaciers can be described as a fraction of a specific retention capacity. Copyright © 2006 John Wiley & Sons, Ltd. 相似文献
11.
12.
自适应Chirplet变换及其在探地雷达目标探测中的应用(英文) 总被引：4，自引：2，他引：2
探地雷达不仅能够探测金属目标体,而且能够探测非金属目标体,而成为UX0和地雷探测的一种重要的浅部地球物理方法。但是在地雷和UX0探测中,目标体埋藏深度浅,在探地雷达数据信噪比较低情况下,地表和土壤层的反射严重干扰对目标体的拾取。本文采用自适用Chirplet变换来消除地表层和土壤层变化的干扰,并在Radon—Wigner分布的基础上,采用自适用Chirplet变换来拾取目标体的信号。通过对实际探测实验数据应用证明,本方法处理结果比传统的偏移方法具有较高的信噪比,并能清晰地提取目标体信号。 相似文献
13.
利用数字图像处理技术提高地震剖面图像信噪比 总被引：1，自引：2，他引：1
提出了利用数字图像处理技术提高地震剖面信噪比的新方法，首先根据数字图像处理要求的格式，对地震剖面数据进行转换，得到地震剖面图像，分析了地震数据特点和初步地震图像的实验结果后，设计了新的预处理方法——“二维沿层滤波”，在此基础上，利用可以计算帧间运动速度及其变化都较大的改进的光流分析技术，计算出多幅地震剖面对应点的偏移量，然后应用图像积累技术对这多幅地震剖面进行积累，实现对三维地震数据体提高信噪比的处理，该方法充分利用了三维地震信息，不但可以提高整个数据体的信噪比，而且可以减少信号能量的损失，并保持原来的信号能量关系，使地震剖面的质量得到明显提高，为地震解释奠定良好的基础。 相似文献
14.
由于金属矿区地震记录中随机噪声性质复杂且信噪比低,常规降噪方法难以达到预期的滤波效果.时频峰值滤波(TFPF)方法是实现低信噪比地震勘探记录中随机噪声压制的有效方法,但其在复杂地震勘探随机噪声下时窗参数优化问题仍难以解决.本文充分利用地震勘探噪声的统计特性,结合Shapiro-Wilk(SW)统计量辨识地震勘探记录中的微弱有效信号,提出基于SW统计量的自适应时频峰值滤波降噪方法(S-TFPF).在S-TFPF方案中,对于有效信号集中区,S-TFPF方法根据信号频率特征,选择有利于信号保持的较短时窗长度;对于噪声集中区,按噪声方差自适应增加时窗长度,增强随机噪声压制能力.S-TFPF应用于合成记录和共炮点记录的滤波结果表明,与传统时频峰值滤波方法相比,S-TFPF方法可以有效抑制低信噪比地震勘探记录中的随机噪声,更好地恢复出同相轴. 相似文献
15.
本文从信号与系统的角度讨论了同步大地电磁时间序列信号之间的依赖关系,选取高信噪比的时间序列信号作为先验数据,用最小二乘法估算依赖关系;结合参考道的数据,合成本地道含噪声时段的数据,最后用合成数据替代噪声段数据,组成新数据,从而在时域中去除大地电磁噪声.西藏地区高信噪比实测数据的试算结果表明,无论电场还是磁场,信号之间的依赖关系是相对稳定的,只与先验数据的长度有关,与时间无关;虽然不同参考点之间的依赖关系不同,但都可以精确合成本地点数据,与参考点地下电性结构和参考距离无关.仿真实验显示,去噪后的信号与原始信号基本一致.实测数据处理结果表明,该方法可以有效去除强噪声干扰,抑制中高频段的近场源效应,同时保留了微弱的有效信号,保证了处理结果的正确性.最后针对方差比方法无法识别的方波噪声,提出了一种简单的平移方法,成功去除了持续时间大于窗口长度的方波噪声;将该方法与远参考技术结合,可以有效抑制近场源噪声干扰,获得光滑连续并且可信的测深资料. 相似文献
16.
针对探地雷达信号处理和分析时小波基选取存在的问题,本文在分析探地雷达信号特点的基础上,首先从理论上讨论小波基的选取准则,然后再从实验角度进行对比、判别,认为在进行小波分解和重构时应该分别选择不同的小波基函数进行处理,这样可以保证重构信号的精确度,增强对信号的处理能力,从而也突破了以往分解与重构时都采用同一个小波基进行处理的做法.最后通过实际资料的处理,指出bior2.6小波基在进行雷达信号处理时效果最佳,不仅去噪彻底,而且能够保留有效信号的高频部分,提高信号的分辨率和信噪比,为后续解释工作打好了基础. 相似文献
17.
当野外噪声很强,即使使用组合震源地震也无法获得满意信噪比的地震数据时,本文提出了一种基于可控震源阵列的定向照明控制方法,采用该方法可形成定向地震波.通过仿真研究合成了8激震器可控震源阵列分别采用简单组合及定向照明技术得到的单炮地震记录,可以看出采用合适的延时参数,定向照明单炮地震记录的反射波信噪比高于组合地震情况.定量的计算结果表明,实验条件下采用0.89 ms延时参数,各反射波信噪比分别提高了10.19 dB,3.23 dB和1.02 dB.由此可见,可控震源定向照明地震技术是一种提高原始地震资料信噪比的有效方法. 相似文献
18.
Ground penetrating radar (GPR) is a powerful tool for detecting defects in and behind reinforced concrete (RC) structures. However, the traditional way of interpreting GPR data involves considerable manpower and is time-consuming. The aim of this study is to illustrate a new approach to recognize GPR images of RC structure voids automatically. Firstly, synthetic GPR images are created by FDTD method. As multiple waves caused by steel bars seriously interfere with the target echo signals, it is difficult to identify targets from the forward modeling images. According to the periodicity of multiple waves from steel bars, the predictive deconvolution method is used to suppress those waves and the outcome is preferable. Then, the support vector machine (SVM) algorithm is proposed to automatically recognize voids in GPR images. The automatic identification procedure includes four steps: 1) collecting training data, 2) extracting features from GPR images, 3) building the SVM model and 4) identifying the voids automatically. The results show that the proposed method provides a suitable tool to locate the cover depths and lateral ranges of the voids, and the trained SVM model gives a favorable outcome when noise (no more than 5%) is added to a synthetic GPR image. 相似文献
19.
Mapping the spatial variation of soil water content at the field scale with different ground penetrating radar techniques 总被引：2，自引：0，他引：2
L. Weihermüller J.A. Huisman S. Lambot M. Herbst H. Vereecken 《Journal of Hydrology》2007,340(3-4):205-216
Two ground penetrating radar (GPR) techniques were used to estimate the shallow soil water content at the field scale. The first technique is based on the ground wave velocity measured with a bistatic impulse radar connected to 450 MHz ground-coupled antennas. The second technique is based on inverse modeling of an off-ground monostatic TEM horn antenna in the 0.8–1.6 GHz frequency range. Data were collected on a 8 by 9 m partially irrigated intensive research plot and along four 148.5 m transects. Time domain reflectometry, capacitance sensors, and volumetric soil samples were used as reference measurements. The aim of the study was to test the applicability of the ground wave method and the off-ground inverse modeling approach at the field scale for a soil with a silt loam texture. The results for the ground wave technique were difficult to interpret due to the strong attenuation of the GPR signal, which is related to the silt loam texture at the test site. The root mean square error of the ground wave technique was 0.076 m3 m−3 when compared to the TDR measurements and 0.102 m3 m−3 when compared with the volumetric soil samples. The off-ground monostatic GPR measured less within-field soil water content variability than the reference measurements, resulting in a root mean square error of 0.053 m3 m−3 when compared with the TDR measurements and an error of 0.051 m3 m−3 when compared with the volumetric soil samples. The variability between the two GPR measurements was even larger with a RSME of 0.115 m3 m−3. In summary, both GPR methods did not provide adequate spatial information on soil water content variation at the field scale. The main reason for the deviating results of the ground wave method was the poor data quality due to high silt and clay content at the test site. Additional reasons were shallow reflections and the dry upper soil layer that cannot be detected by the ground wave method. In the case of off-ground GPR, the high sensitivity to the dry surface layer is the most likely reason for the observed deviations. The off-ground GPR results might be improved by using a different antenna that allows data acquisition in a lower frequency range. 相似文献
20.
短周期密集台阵的高频背景噪声互相关函数(NCF)是探查地球浅层精细结构的重要数据.然而高频背景噪声成分复杂且容易分布不均,分析其对NCF信号提取的影响,有助于获取可靠成像结果.本文基于布设于川滇地区盐源盆地的209个短周期台站组成的盐源台阵,利用密集台阵的噪声水平评估以及基于NCF的相干噪声分析两种方法,分析了其记录到的噪声波场特征及其对NCF的影响.结果表明,盐源台阵的整体噪声水平呈现北低南高的不均匀分布,高频噪声水平的强弱受控于当地的人类活动,亦受到浅部松散沉积层的影响.台阵垂直分量NCF中主要信号为基阶Rayleigh波,且产生该信号的相干噪声源的优势方位在不同频带具有较大区别:0.3～0.5Hz的噪声源强度较强且随时间变化较为稳定,主要能量来自台阵的南侧;0.5～1Hz的相干噪声源强度较低,有两个优势方向,其中较强的一个来自于台阵南侧,可能与0.3～0.5 Hz的噪声同源,较弱的一个来自于台阵北偏东方向;1～1.5Hz的背景噪声有四个较弱的优势方向,在台阵的不同区域有不同的优势方向,可能受到不同的局部噪声源的控制.垂向NCF中Rayleigh波的信噪比主要受控于波场的复杂程度,台阵南部受人文活动及沉积层影响,噪声水平较高,且由于盆山边缘复杂的反射、散射作用,其NCF波形复杂,信噪比偏低.受高频噪声源分布不均与及复杂地质结构的共同影响,盐源台阵的高频NCF中的信号复杂,后续对面波频散特征的提取应充分考虑噪声源对NCF的影响以获取可靠结果. 相似文献