共查询到20条相似文献，搜索用时 15 毫秒
1.
This paper presents a series of cyclic 2D direct shear tests on sand–rough material interfaces under constant normal load (CNL) and constant normal stiffness (CNS) conditions. The aim of these tests is to describe the behavior of the soil–pile contact subjected to a large number of cycles due to environmental or anthropic loadings. These cycles (typically 104 or less due to an early rupture) are small (10, 20 and 40 kPa in terms of shear stress). A new interpretation of the direct shear tests is proposed. The sample of soil is schematically composed of a sheared interface and of a buffer under oedometric load. The problem of sand leakage between the shear box and the rough plate, classical phenomenon in this type of test, is focused. The effect of initial density, position of “center of cycles” in stress plane (mean cyclic variables) and cyclic amplitude is investigated. The cycles are defined by the initial mean cyclic normal stress, the level of initial mean cyclic stress ratio and the normalized cyclic amplitude. Under CNL condition, either dilation or contraction is exhibited, in agreement with the characteristic state developed by Luong (International symposium on soils under cyclic and transient loading, Swansea, 7–11 January, pp 315–324, 1980). The influence of a prescribed normal stiffness is especially considered. It can be highlighted that CNS cyclic paths are always contractive. This contraction results in a drop of mean cyclic normal stress often called degradation of friction. 相似文献
2.
Hanifi Missoum Mostefa Belkhatir Karim Bendani Mustapha Maliki 《Geotechnical and Geological Engineering》2013,31(1):279-296
In a number of recent case studies, the liquefaction of silty sands has been reported. To investigate the undrained shear and deformation behaviour of Chlef sand–silt mixtures, a series of monotonic and stress-controlled cyclic triaxial tests were conducted on sand encountered at the site. The aim of this laboratory investigation is to study the influence of silt contents, expressed by means of the equivalent void ratio on undrained residual shear strength of loose, medium dense and dense sand–silt mixtures under monotonic loading and liquefaction potential under cyclic loading. After an earthquake event, the prediction of the post-liquefaction strength is becoming a challenging task in order to ensure the stability of different types of earth structures. Thus, the choice of the appropriate undrained residual shear strength of silty sandy soils that are prone to liquefaction to be used in engineering practice design should be established. To achieve this, a series of undrained triaxial tests were conducted on reconstituted saturated silty sand samples with different fines contents ranging from 0 to 40 %. In all tests, the confining pressure was held constant at 100 kPa. From the experimental results obtained, it is clear that the global void ratio cannot be used as a state parameter and may not characterize the actual behaviour of the soil as well. The equivalent void ratio expressing the fine particles participation in soil strength is then introduced. A linear relationship between the undrained shear residual shear strength and the equivalent void ratio has been obtained for the studied range of the fines contents. Cyclic test results confirm that the increase in the equivalent void ratio and the fines content accelerates the liquefaction phenomenon for the studied stress ratio and the liquefaction resistance decreases with the increase in either the equivalent void ratio or the loading amplitude level. These cyclic tests results confirm the obtained monotonic tests results. 相似文献
3.
采用南海北部区域油田场址钻孔原状土样,开展黏土循环动力特性试验研究。结合共振柱与应变控制的循环单剪试验,获取动剪切模量和阻尼比随循环剪应变的变化规律,将最大动剪切模量与原位静力触探的计算结果进行对比。开展应力控制的循环单剪试验,采用对称加载方式获取土样动强度阈值,基于该阈值,通过单、双向加载方式获取土样动强度包络线,并将试验结果与Drammen黏土及世界范围内其余区域黏土进行对比。该研究初步获取了南海北部区域性黏土的循环特性及动力学参数,为南海北部区域油气田结构设计和地质风险评估提供基础资料,掌握了循环动力特性试验方法,为岩土工程动力学试验研究及数据分析提供技术参考。 相似文献
4.
为了研究筋-土界面在遭受动力作用时的表现,利用大型直剪仪对土工格栅、土工编织布、土工无纺布和砂土界面进行了一系列循环剪切试验,得到了不同工况下界面的剪切刚度和阻尼比,并探究了循环次数与剪切刚度和阻尼比之间的规律。研究结果表明,同一循环次数时格栅-土界面的循环剪切刚度最大,土工编织布-土界面的阻尼比最大;剪切位移幅值为3 mm时3种竖向应力下界面都呈现出循环剪切硬化的特征,随着循环次数的增加,各竖向应力下的界面阻尼比有趋于某一值的趋势;砂土密实度越大,同一循环次数对应的剪切刚度越大,阻尼比越小,且随着循环次数的增加3种砂土密实度的界面阻尼比有趋于同一值的趋势;循环剪切位移幅值为5 mm的界面发生循环剪切软化现象,剪切位移幅值越大,界面同一循环次数的阻尼比也越大。 相似文献
5.
6.
Yu Haizhen Zhao Wenguang Wang Ren Li Jianguo He Yang 《中国地质大学学报(英文版)》2005,16(4):340-344
INTRODUCTION Theexploitationofoffshorenaturalresourcesin thetropichaspresentedgeotechnicalengineerswith theproblemofdealingwithinsitucarbonatesedi mentsinharshconditionsforwhichfewengineering dataareavailable.Thecarbonatesedimentsaresub jectedtolargestaticstressesduetotheweightof foundationstructuresaswellascyclicstressesdueto waveaction,andinsomecases,earthquakeloading.Ithasbeenprovedthatthenatureofcyclicstresschangesoccurringintheseabeddepositduetowave loadinginvolvesacontinuousrotationo… 相似文献
7.
The seismic performance of a tailings impoundment can be adversely affected by the behavior of the retained tailings. However, there remains considerable uncertainty in tailings liquefaction analysis. Twenty cyclic simple shear tests conducted on tailings from a gold mine in Quebec, Canada, were simulated numerically. The simulations indicated that the dynamic behavior of tailings could be modelled reasonably well, except that the weighted cyclic resistance curve of the tailings differed from that of clean sand which was used to develop the constitutive model (UBCSAND). An (N1)60-CS value of 10 blows/30 cm was estimated for the tailings based on calibration at a CSR of 0.10 for 15 cycles of loading. Numerical simulation of the behavior of a 20-m-high deposit of tailings during an earthquake (Mw = 5.9) indicated liquefaction of the upper 8 m of tailings. Liquefaction analysis using the Simplified method with published magnitude scaling factors (MSF) did not predict the occurrence of liquefaction. The use of MSF values calculated from the laboratory testing predicted liquefaction in the upper 8 m of tailings, corresponding quite well with the numerical simulation. The results indicate that both analytical and numerical methods can be used to evaluate the potential for tailings liquefaction under seismic loads. 相似文献
8.
钙质砂与钢板接触面力学特性试验研究 总被引：3，自引：0，他引：3
对一种人工制备的钙质砂与光滑铜板接触面进行了一系列的单调和循环剪切试验,表明钙质砂与光滑钢板的接触属于摩擦接触,界面剪应力与正应力之比与剪切位移关系有较好的归一性。等正应力试验中钙质砂的的缩性较大;等体积试验中接触面的抗剪强度因正应力的降低而远低于等正应力试验;循环剪切中加荷与卸荷曲线基本重合,经历循环剪切作用后接触面的抗剪强度有降低的趋势。界面湿摩擦系数低于干摩擦系数。 相似文献
9.
Raj Banerjee Sanku Konai Aniruddha Sengupta Kousik Deb 《Geotechnical and Geological Engineering》2017,35(4):1327-1340
As a part of the seismic safety evaluation of several bridges and other hydraulic structures located on Kasai River bed in India, the liquefaction potential of Kasai River sand is studied in 1-g shake table in laboratory and numerically using a commercial software FLAC 2D. The surface settlement, lateral spreading, predominant frequency, amplification of the ground motion and pore water pressure development in Kasai River sand in dry and liquefied states have been studied when subjected to sinusoidal motions of amplitude 0.35 g at a frequency of 2 Hz. The nonlinear curves used to represent shear strain dependency of stiffness and damping ratio of Kasai River sand are obtained from cyclic triaxial tests. Reasonably good agreement between the experimental and the numerical results is observed. It is found that the settlement and lateral spreading for the liquefied sand is 2.60 and 2.50 times than those of the sand in the dry state. The volumetric strain of the liquefied sand is found to be around 4%, which is significantly higher than 1.53% observed in the dry sand. It is observed that the amplification of the peak ground acceleration for the saturated sand is 1.08 and 1.32 times higher than that for the dry sand from theoretical and experimental results, respectively. The shear strain developed in the liquefied sand is 1.17 times more than that for dry sand. The fundamental and higher modal frequencies of dry sand are found to be 1.13, 1.117 and 1.119 times more than those for the saturated sand, respectively. 相似文献
10.
Chunyang Liu Hoda Soltani Kanthasamy K. Muraleetharan Amy B. Cerato Gerald A. Miller Sri Sritharan 《Acta Geotechnica》2016,11(6):1431-1444
Presented in this paper are results of two centrifuge tests on single piles installed in unimproved and improved soft clay (a total of 14 piles), with the relative pile–soil stiffness values varying nearly two orders of magnitude, and subjected to cyclic lateral loading and seismic loading. This research was motivated by the need for better understanding of lateral load behavior of piles in soft clays that are improved using cement deep soil mixing (CDSM). Cyclic test results showed that improving the ground around a pile foundation using CDSM is an effective way to improve the lateral load behavior of that foundation. Depending on the extent of ground improvement, elastic lateral stiffness and ultimate resistance of a pile foundation in improved soil increased by 2–8 times and 4–5 times, respectively, from those of a pile in the unimproved soil. While maximum bending moments and shear forces within piles in unimproved soil occurred at larger depths, those in improved soil occurred at much shallower depths and within the improved zone. The seismic tests revealed that, in general, ground improvement around a pile is an effective method to reduce accelerations and dynamic lateral displacements during earthquakes, provided that the ground is improved at least to a size of 13D × 13D × 9D (length × width × depth), where D is the outside diameter of the pile, for the pile–soil systems tested in this study. The smallest ground improvement used in these tests (9D × 9D × 6D), however, proved ineffective in improving the seismic behavior of the piles. The ground improvement around a pile reduces the fundamental period of the pile–soil system, and therefore, the improved system may produce larger pile top accelerations and/or displacements than the unimproved system depending on the frequency content of the earthquake motion. 相似文献
11.
地震引起的土体液化和地基失效对岩土工程师而言仍是一个热点问题。地震液化及地基变形可以采用多种地基加固方法防治,碎石桩技术是常用方法之一。碎石桩复合地基抗液化效用主要是增加桩周土体的密度、桩体的排水以及桩体分担地震水平剪应力作用(桩体减震作用)。目前,以抗液化为主的碎石桩复合地基的设计以及效果评价方法仍只考虑加密作用。首先通过3个模型(1个饱和砂土地基模型、2个碎石桩复合地基模型)的振动台试验研究抗液化碎石桩的减震作用。然后以试验记录的模型动力反应以及建立的理论模型为基础,分析碎石桩复合地基的桩体减震作用。试验及理论分析结果表明,复合地基中的碎石桩可以明显地降低作用在桩间可液化土上的地震剪应力。 相似文献
12.
A new constitutive law for the behaviour of undrained sand subjected to dynamic loading is presented. The proposed model works for small and large strain ranges and incorporates contractive and dilative properties of the sand into the unified numerical scheme. These features allow to correctly predict liquefaction and cyclic mobility phenomena for different initial relative densities of the soil. The model has been calibrated as an element test, by using cyclic simple shear data reported in the literature. For the contractive sand behaviour a well‐known endochronic densification model has been used, whereas a plastic model with a new non‐associative flow rule is applied when the sand tends to dilate. Both dilatancy and flow rule are based on a new state parameter, associated to the stiffness degradation of the material as the shaking goes on. Also, the function that represents the rearrangement memory of the soil takes a zero value when the material dilates, in order to easily model the change in the internal structure. Proceeding along this kind of approach, liquefaction and cyclic mobility are modelled with the same constitutive law, within the framework of a bi‐dimensional FEM coupled algorithm developed in the paper. For calibration purposes, the behaviour of the soil in a cyclic simple shear test has been simulated, in order to estimate the influence of permeability, frequency of loading, and homogeneity of the shear stress field on the laboratory data. Copyright © 2006 John Wiley & Sons, Ltd. 相似文献
13.
Ardeshir Dehmoobed Sharif-abadi Tim Grain Joseph 《Geotechnical and Geological Engineering》2010,28(4):471-481
Strain softening of oil sand under dynamic loading from large mining equipment inhibits the ability of the equipment to function
at optimal design performance. This paper looks at the findings of dynamic plate load tests, which effectively mimick the
loading and unloading action of a shovel track pad. A pseudo-elastic model was proposed based on the results of the dynamic
plate load testing to predict the deformation of oil sand under cyclic loading. Both field and laboratory cyclic plate load
tests were performed on oil sand materials. The field tests were performed with different plate sizes, or footprints. The
load was normalized based on the pressure stiffness concept in units of pressure per unit deformation. FLAC was used to model
the field plate load test deformation with the elastic concept. The laboratory tests were performed at room temperature with
more control on the load, loading rate, and cycles than possible during the field testing. Tests were conducted using a circular
plate of 14.9 cm diameter, at stress magnitudes of 200, 400, 500 and 600 kPa. The plate load tests were conducted for varying
loads, holding, and relaxation times of 0, 2, 5 and 10 min respectively for each magnitude of stress. The outcome of laboratory
plate load tests show that after frequent cycles, the pressure stiffness (ratio of stress to deformation) converges on a plateau
value of 8 kPa/mm. The proposed approach can be used to evaluate oil sands ground performance, enhancing the prediction process
for ground deformation under the operation of ultra-class mining equipment. 相似文献
14.
采用现场液化试验,研究水平场地孔压增长模式,提出孔压增量计算模型。通过不同密实度砂土的液化试验,以加速度、埋深、砂土密实度等现场参数为指标构建孔压增量模型,发现现场和室内试验孔压增长模式的区别和联系,并验证该孔压模型的可靠性。研究结果表明：等幅循环荷载下,与现有动三轴等土单元试验的孔压增量随作用次数一直呈单调递减模式不同,现场试验孔压增量随作用次数呈现出先增大后减小的规律,中间存在阈值;通过参数分析和试验实例验证,构建的孔压增量计算模型,可更方便地用于随机荷载下水平场地的饱和砂土孔压计算。 相似文献
15.
高应力下剪切速率对砂土抗剪强度影响研究 总被引：2，自引：0，他引：2
应用DRS-1型高压直剪仪,进行了16组法向应力水平、5种剪切速率条件下福建标准砂的抗剪强度试验,试验结果表明,高应力下砂土的抗剪强度受法向应力和剪切速率的共同影响。法向应力和剪切速率通过影响颗粒破碎和颗粒重排列程度等试样的细观参数,决定了砂土宏观上抗剪强度的发挥。当法向应力较小时,砂土抗剪强度与剪切速率基本无关;但是当法向应力较大时,较快剪切速率条件下的砂土抗剪强度变小,且其摩尔强度包线出现了“下弯-上扬”循环波动,因此不可以忽略剪切速率对砂土抗剪强度的影响。 相似文献
16.
橡胶砂作为轻质耗能填料在工程中应用广泛,其含水状态随应用领域及外界因素变化而不同。研究含水率变化对橡胶砂动剪模量和阻尼比的影响,对于其合理应用具有重要意义。利用大型循环单剪试验装置对6种含水率的橡胶砂在3种竖向压力下进行了循环剪切试验,得到了动剪应变幅值在1%～3%范围时,橡胶砂动剪模量和阻尼比随含水率变化的试验现象。结果表明：橡胶颗粒的加入使得纯砂的动剪模量随含水率的衰减受到抑制,当橡胶颗粒含量达到30%时,橡胶砂动剪模量随含水率的增大反而表现出增大的趋势;随着橡胶颗粒含量的增大,橡胶砂阻尼比随含水率的增大表现出衰减的趋势;虽然离散性较大,但含水率对橡胶砂动力特性的影响不可忽略,橡胶砂动剪模量受含水率影响的平均最大变化幅值可达20%,阻尼比受含水率影响的平均绝对变化值接近0.025;在动力特性随含水率的稳定性方面,橡胶颗粒质量含量为20%的橡胶砂表现相对较好。 相似文献
17.
Use of scrap tyres in isolation systems for seismic damping, requires a knowledge of the engineering properties of sand–rubber mixtures (SRM). The primary objective of this study is to assess the influence of granulated rubber and tyre chips size and the gradation of sand on the strength behaviour of SRM by carrying out large-scale direct shear tests. A large direct shear test has been carried out on SRM considering different granulated rubber and tyre chip sizes and compositions. The following properties were investigated to know the effect of granulated rubber on dry sand; peak shear stress, cohesion, friction angle, secant modulus and volumetric strain. From the experiments, it was determined that the major factors influencing the above-mentioned properties were granulated rubber and tyre chip sizes, percentage of rubber in SRM and the normal stress applied. It was observed that the peak strength was significantly increased with increasing granulated rubber size up to rubber size VI (passing 12.5 mm and retained on 9.5 mm), and by adding granulated rubber up to 30%. This study shows that granulated rubber size VI gives maximum shear strength values at 30% rubber content. It was also found that more uniformly graded sand gives an improved value of shear strength with the inclusion of granulated rubber when compared to poorly graded sand. 相似文献
18.
不排水循环荷载作用过程中累积孔压对细砂弹性剪切模量Gmax的影响 总被引：1，自引：1，他引：0
在土工结构物地震有效应力分析中,往往采用Hardin经验公式计算动荷作用过程中由于孔压变化对砂土初始弹性剪切模量Gmax的影响,但由于以往试验手段的限制,这种方法的有效性至今没有得到验证。为此,采用多功能三轴仪和压电陶瓷弯曲元剪切波速测试系统,研究了不排水循环荷载过程中孔压对细砂Gmax的影响。试验结果表明,细砂Gmax可由 Hardin型经验公式计算,但材料参数应通过试验确定;不排水循环荷载作用过程中,细砂Gmax随孔压上升而降低,其值可由其实际平均有效应力和固结后的孔隙比通过由试验得到的Hardin型经验公式计算。 相似文献
19.
K0固结条件下砂土的循环剪切特性试验研究 总被引：1，自引：0，他引：1
利用土工静力-动力液压三轴-扭转多功能剪切仪,针对福建标准砂Dr = 30 %,在K0固结条件下,进行不同围压下的循环三轴试验,探讨了K0固结过程和K0固结条件下砂土的孔隙水压力特性与强度特性,并与原有均等固结条件和非均等固结条件下的循环三轴试验进行对比分析。通过分析和比较表明,砂土的K0固结试验过程可以分为两个阶段,第1个阶段是初期的缓慢变形阶段,第2个阶段是后期的稳定发展阶段,围压对静止土压力系数K0的测定有一定影响。不同固结过程对砂土动孔隙水压力的发展有很大的影响,K0固结条件下试样出现明显的剪胀现象。另外,K0固结条件下砂土动强度高于非均等固结条件（Kc = 1.67）下砂土动强度,低于非均等固结条件（Kc =2.94）下砂土动强度。 相似文献
20.
常德-张家界高速公路某大桥桥基砂土液化评价 总被引：2，自引：0，他引：2
结合常德张家界高速公路某大桥桥基工程,在DSD160型电磁式振动三轴试验仪上,通过往返加荷三轴试验,对饱和砂土进行了液化试验研究,探讨了基于动三轴液化试验结果判断饱和砂土液化的方法。并尝试了这种室内研究反应分析的液化可能性估计方法与地震剪应力时程相结合的综合判断方法。在该高速公路大桥桥基的饱和砂土液化评价中,采用这种综合判断方法,对大桥桥基砂土液化进行了判断。在判断场地是否液化后,对其液化危害程度进行了等级划分,给出了该工程场地在未来遭受到不同超越概率下的地震作用时发生液化的危害程度,得到了一些有工程实用意义的结果。 相似文献