首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 46 毫秒
1.
针对导管架式海洋平台结构型式与特点,利用冲击隔振理论,将冰锥体与隔振技术结合起来,提出一种能有效降低冰荷载激励的"两级柔性隔振锥体"设计方案。建立了两极隔振锥体简化计算模型,确定了系统振动传递系数参数之间的关系。通过建立海洋平台有限元模型,采用有限元程序,进行了模拟冰荷载激励下的振动响应分析,并对安装隔振装置的小比例模型结构进行了冲击荷载下的减振试验。结果表明采用"两级柔性隔振锥体"能有效降低传递给海洋平台的冰力极值,减小海洋平台冰激励的响应。  相似文献   

2.
在海冰与多桩锥体海洋平台结构的相互作用中,平台结构总冰力在海冰流向和桩腿方位的影响下呈现出显著的遮蔽效应。采用具有粘结-破碎效应的离散元方法,基于GPU并行的高性能计算,对不同冰向下锥体海洋平台结构的冰荷载进行了数值分析,确定了不同冰向下平台结构各桩腿的冰力衰减系数并分析了总冰力的遮蔽效应。最后,对自由边界影响下多桩平台结构冰荷载遮蔽效应的产生机理进行了讨论。本文工作可为多桩腿平台结构的冰荷载特性、冰激结构振动以及冰区结构设计提供参考。  相似文献   

3.
近海平台冰荷载的一个新的频域识别方法   总被引:3,自引:0,他引:3  
本文给出了利用实测的加速度响应曲线和已知的初始条件识别平台所受冰荷载的频域新方法,并对实际的平台进行了识别。  相似文献   

4.
基于黏聚单元法的抗冰海洋平台与层冰相互作用数值模拟   总被引:1,自引:1,他引:0  
通过商业有限元软件LS-DYNA采用黏聚单元法模拟层冰的断裂问题,在IIHR冰池模型试验相同缩尺比参数下对KULLUK抗冰平台受到的冰力进行数值计算,探究冰厚与冰速等冰况参数对平台冰力的影响。计算结果表明,在极地作业平台主要遭遇北极海域冰况范围下,相同冰厚情况时冰速变化对倒锥形结构平台的横向冰力影响不大,而同冰速时冰力随着冰厚的增加接近线性增加。同时将计算所得结果与同条件下IIHR冰池模型试验数据、ARCTEC、ACL非冻结模型冰试验数据、实船数据和通过ISO19906规范中提供的针对大锥面结构受到层冰冰力的经验公式计算所得数据等进行了对比,验证了选用冰参数的可靠性以及该数值模型在模拟大尺度宽锥形平台遭受层冰作用问题中的适用性。  相似文献   

5.
自升式钻井平台在设计时通常不考虑冰荷载的作用,要实现冰区作业,首先需要对该类平台的抗冰能力进行准确评估。本文通过开展冰池试验,对自升式钻井平台冰载荷作用机理、结构冰激特性以及抗冰方法等进行研究。海洋结构受到的冰荷载大小以及结构响应值与冰厚密切相关,冰激振动机理与冰厚无关,探究不同冰速和冰厚下冰荷载及振动响应的时程曲线,可发现低冰速下结构展现出的准静态响应特征以及高冰速下的随机响应特征。冰激振动的发生是结构固有特性、冰速、冰厚、冰材料参数等因素共同影响的结果,其作用机理尤为复杂,本研究侧重于桁架式自升式平台冰区作业中结构冰激振动特性研究。  相似文献   

6.
针对海上风电结构,研究了环境激励下海上风电结构的模态参数识别问题。采用了一种时域联合算法:自然激励法(Natural Excitation Technique,简称NExT)和多参考点复指数法(Polyreference Complex Exponential,简称PRCE)的结合(简称NExT/PRCE方法)对海上风电结构的模态参数进行识别。对某三脚架式海上风电结构进行数值模拟,考虑了风电结构的实际操作工况,对结构施加了随机波浪荷载和风机载荷。利用动力响应数据进行了环境激励下风电整体结构模态参数识别,采用了稳定图与模态置信准则进行了虚假模态的剔除,并分析了NExT中参考通道选取对于模态参数识别效果的影响。通过与有限元模型模态参数比较,验证了NExT/PRCE方法对于风电结构参数识别的有效性。  相似文献   

7.
将特征系统实现法(ERA)与CBSI算法相结合识别海洋平台结构的模态参数(固有频率,阻尼比,振型),利用有限的加速度信号进行结构模态参数识别。海洋平台结构数值模型模拟的动力响应信号用于参数识别。所识别出的海洋平台模态参数与有限元ANSYS分析所得的结果相比较,表明运用本文所提出的方法进行模态参数识别是有效的。  相似文献   

8.
损伤识别是海洋平台结构健康监测的核心问题,对于保障结构的安全服役具有重要的意义。文中将交叉模型交叉模态(CMCM)有限元模型修正方法应用到了导管架式海洋平台结构的损伤识别中。针对实测模态含噪声条件下该方法遇到的"病态"求解难题,引入了截断奇异值分解正则化方法,提出了基于正则化模型修正的损伤识别过程。为验证该过程的有效性,制做了某导管架平台的钢质缩尺简化模型,并在两个典型构件处设置了损伤;利用冲击激励对结构进行了振动测试;根据模态识别结果,采用正则化模型修正过程对各损伤工况进行了损伤识别。结果表明,利用有限的低阶含噪声模态,借助正则化求解技术,该模型修正方法可有效地识别导管架平台结构的损伤。  相似文献   

9.
海洋平台响应多点解耦的冰力测量方法   总被引:3,自引:0,他引:3  
刘建成  顾永宁 《海洋工程》2000,18(2):7-12,23
提出了一种通过传递函数在频域内进行解耦逆推多点冰力的计算方法,并以一个四桩腿平台为例,给出了冰力问接测量的设计方案及计算流程,从而为解决海上平台所受冰力的测量问题找到一个较好的技术途径。  相似文献   

10.
基于实测动冰力时程的海洋平台结构冰振反应分析   总被引:13,自引:2,他引:11  
冰激平台结构振动是影响渤海石油钻采平台冬季正常生产和安全的主要因素。本文采用实测冰压力时程,对渤海辽东湾北部的JZ20-2MUQ平台结构进行了冰振反应分析,计算了不同设计冰厚、不同冰作用方向和标高及平台桩腿有无正倒锥体(一种破冰装置)的结构反应,探讨了正倒锥体对减轻冰力和结构反应的作用,发现了结构冰激振动的一些特征,为在该平台上实施振动控制方案提供了依据  相似文献   

11.
In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance.  相似文献   

12.
海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明:土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。  相似文献   

13.
An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm.  相似文献   

14.
This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested.  相似文献   

15.
Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement.  相似文献   

16.
17.
18.
The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments.  相似文献   

19.
A set of 27 marine planktonic bacteria isolated from the polar regions was characterized by 16S rDNA sequencing and physiological and biochemical testing. More than half of these bacteria were positive for caseinase, gelatinase and 13-glucosidase, and could utilize glucose, maltose or malic acid as carbon source for cell growth. Twelve isolates expressed nitrate reduction activities. Except for one antarctic isolate BSwlO175 belonging to Actinobacteria phylum, these isolates were classified as γ-Proteobacteria, suggesting that γ-Proteobacteria dominated in cultivable marine bacterioplankton at both poles. Genus Pseudoalteromonas was the predominant group in the Chukchi Sea and the Bering Sea, and genus ShewaneUa dominated in cultivable bacterioplankton in the Prydz Bay. With sequence similarities above 97%, genus Psychrobacter was found at both poles. These 27 isolates were psychrotolerant, and significant 16S rDNA sequence similarities were found not only between arctic and antarctic marine bacteria ( 〉 99% ), but also between polar marine bacteria and bacteria from other aquatic environments ( ≥ 98.8% ), including temperate ocean, deep sea, pond and lake, suggesting that in the polar oceans less temperature-sensitive bacteria may be cosmopolitan and have a bipolar, even global, distribution at the species level.  相似文献   

20.
Oedometer tests have been carried out on 70 undisturbed surficial clays (at approximately 250 mm below the mudline), mostly collected by free-fall corers from sites widely scattered throughout the deep-sea North Atlantic. Acoustic measurements were also made, initially on contiguous samples and ultimately on the same sample using a geophysically instrumented oedometer which also collected electrical resistivity data. Apart from those quiescent areas below the carbonate compensation depth, such as north of the West Indies where very fine clays exist, most of the samples are silty clays whose geotechnical-geophysical properties are dependent on the type of clay minerals present (and their ability to take in moisture), the sand-size fraction, and the quantity of carbonate present. Thus the pure clays have high compressibilities which decrease on the addition of coarse particles, while the converse is true for the acoustic parameters, these increasing with the sand fraction. Using the notion of the intrinsic compression line for all samples, and comparison to it of the measured compression curves, it is clear that, contrary to some previously held ideas, most deep-sea clays are normally consolidated; the addition of carbonate has the effect of creating an open, stronger sediment skeleton. Interestingly, where information is available, the variation with depth of a sample's acoustic velocity follows the void ratio pressure relationship of the compression curve. This allows the construction of an in-situ sediment compression curve using the in-situ geophysical observations.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号