共查询到20条相似文献，搜索用时 78 毫秒
1.
提出了一种基于废旧轮胎的公路路堤局部坍塌快速抢修方法,主要使用废旧轮胎配重块与工字钢.废旧轮胎配重块为在废旧轮胎内部浇筑钢筋混凝土形成,制作简单,价格低廉,组装形成的护坡结构整体强度高、稳定性大,施工简单方便,施工速度快,满足路堤坍塌抢修的紧迫性需求。 相似文献
2.
废旧轮胎胎面挡土墙是一种有效利用废旧轮胎的理想途径,但直立的模块式废旧轮胎胎面挡土墙不能承受高强度的地震作用,因而提出格栅条带式加筋的方法提高其抗震性能。根据土-结构动力相似体系,设计格栅条带式加筋废旧轮胎胎面挡土墙振动台试验模型,考虑地震强度、地震波、格栅加筋长度、格栅加筋间距以及墙面坡度的影响,分析胎面墙体与回填料加速度、墙体侧向位移、墙顶表面回填料沉降以及墙背动土压力等地震响应特征,并与无加筋的废旧轮胎胎面挡土墙的振动台模型试验进行对比。研究结果表明:格栅条带式加筋胎面挡土墙的方式显著改善了无加筋状态的胎面挡土墙的地震响应特征,提高了胎面挡土墙的抗震性能,格栅条带式加筋直立式废旧轮胎胎面挡土墙可以作为理想的墙体进行工程推广应用。 相似文献
3.
采用Mn/RE多相催化电解氧化方法深度处理垃圾渗滤液,制备了负载型Mn/RE氧化物双活性组分催化剂,研究了Mn/RE负载型催化剂的制备条件(不同组分的浓度配比,焙烧温度,催化剂载体材料)对电多相催化氧化降解垃圾渗滤液中有机物的影响,确定催化剂的适宜制备条件研究结果表明:催化剂中Mn 与稀土组分复合其催化活性好于单一组分,其中以Ce+ Mn制备的催化剂效果最好;浸渍液金属离子质量分数Mn为3％、Ce为1％,焙烧温度为550℃.以γ-Al2O3为载体时所制得的催化剂活性较高并且该催化剂的性能稳定,经6次使用后仍具有一定的催化活性.对于COD为533mg/L的渗滤液生物处理出水的电解氧化降解,采用催化剂后,COD去除率由26.9％提高到71 76％,可有效降低COD. 相似文献
4.
为克服传统刚性拦石结构体系,刚性过大,受落石冲击易破坏,场地适应性差等缺点,设想将汽车废旧轮胎堆栈于刚性拦石结构前,形成一种刚柔并重的结构体系。利用废旧轮胎的弹性和韧性缓解落石的冲击力,从而提高传统刚性拦石结构体系防护落石的能力。并通过利用LS-DYNA有限元软件对废旧轮胎在落石冲击作用下的耗能性能进行了分析,计算结果表明废旧轮胎具有较好的吸能效果,对提高刚性拦石结构体系的防护能力有很大的帮助。 相似文献
5.
用废聚苯乙烯泡沫制备胶粘剂 总被引：1，自引：0，他引：1
本文研究了回收废旧聚苯乙烯(PS)泡沫塑料制备PS胶粘剂的方法。以废旧聚苯乙烯泡沫塑料为主要原料,选择低毒性、相溶性好的有机溶剂,使其溶解,再与聚乙烯醇(PVA)水溶液共混,制得水包油乳液。加入不同改性材料,制得改性胶粘剂。 相似文献
6.
废旧轮胎胶粉用于填埋场衬垫材料改性,是提高衬垫系统有效性和扩展废旧轮胎资源化利用途径的一种手段。以高岭土作为黏性土的代表,开展废旧轮胎胶粉-高岭土混合土的力学和水力学性质试验,重点探讨胶粉掺量及尺寸对混合土渗透性、压缩性和收缩性的影响规律。研究表明,废旧轮胎胶粉-高岭土混合土的渗透系数、压缩系数、回弹指数、固结系数和体缩率等均随胶粉掺入比的增加而增大。高岭土及混合土的无侧限抗压强度大于200kPa,50kPa和200kPa压力下渗透系数满足≤1.0×10-7cm·s-1的要求,均属于中压缩性土,且体缩率小于体积应变合格值4%。与30目胶粉相比,12目胶粉-高岭土混合土压缩性和回弹量较小、固结系数较大,胶粉尺寸对无侧限抗压强度、体缩率和渗透系数的影响不显著。在本文试验条件下,为提高黏土衬垫对有机污染物的吸附能力并满足渗透性、强度及变形的要求,12目25%胶粉改性黏土可作为填埋场黏土衬垫材料。 相似文献
7.
废旧轮胎的治理是一个世界性的难题,而将废旧轮胎应用于岩土工程加固中则为其污染治理提供了一个行之有效的手段。为了进一步研究废旧轮胎对土体的加固机制并应用到实际工程中,主要选取了全风化花岗岩砂颗粒和加工后的废旧轮胎（包括颗粒型和长条型）的混合体作为研究对象,通过一系列不同竖向压力下的一维压缩试验,详细研究不同橡胶含量配比、不同形态下的橡胶-砂混合体的受压力学特性,并创新性地探讨了橡胶颗粒对砂颗粒在压缩过程中破碎行为的影响。试验结果表明,所有橡胶-砂混合体在较高压力作用下都能收敛到一条直线,即存在唯一的标准压缩线;随着橡胶含量增加到大于20%,混合物的压缩和卸载回弹量均明显增加,而这种特性不受轮胎颗粒形态的影响。此外,轮胎橡胶含量配比越高,砂颗粒的破碎程度越小,同时,当其中砂颗粒尺寸越小时,整体破碎越少。 相似文献
8.
本文介绍了同步辐射X射线吸收光谱（XAS）在环境矿物学中的应用与进展,尤其是在矿物载体催化剂的环境催化活性研究、固-液界面的微观机制研究、毒性痕量元素在矿物中赋存状态的研究、核废料的矿物处置研究等方面的发展现状。最后指出,XAS对推动环境矿物学的发展、优化环境矿物材料和原料的工艺流程具有独特的优势,在我国还有待进一步加强其发展和应用。 相似文献
9.
传统的Fenton均相亚铁盐催化剂处理染料废水,具有难以避免的二次污染和亚铁离子流失问题。分子筛催化剂相比传统催化剂具有高效环保的特点,在催化氧化染料废水领域有着良好的前景。本文通过液相离子交换法制备了Fe-ZSM-5非均相分子筛催化剂,替代传统的亚铁盐催化剂,应用X射线衍射对制备的Fe-ZSM-5分子筛催化剂进行表征,表明随离子交换次数的增加,Fe-ZSM-5催化剂负载的铁量上升,且较好地保持了分子筛结构,有利于提高亚铁离子的催化能力。通过实验确定了Fe-ZSM-5催化剂催化反应的最佳温度、pH值、Fe-ZSM-5的用量、反应时间等工艺参数,比较了Fe-ZSM-5催化剂和传统Fenton均相催化剂降解染料废水的脱色率和废水中铁离子的残留量,结果表明Fe-ZSM-5的脱色率达到98.5%,相比于Fenton均相催化剂的脱色率提升约3%;两种催化剂的铁离子残留量差别显著,Fe-ZSM-5催化剂处理的废水中只产生微量的Fe离子,可以认为Fe-ZSM-5非均相分子筛催化剂有效地解决了催化剂损耗和二次污染问题。 相似文献
10.
在918碱性镀液中,镍的络合物非常稳定,测定电镀Zn-Ni合金镀液中的Zn2 、Ni2 ,采用沉淀、烘干称重测镍,将滤液滴定分析锌,手续繁,时间长．本文研究了918碱性镀液中直接测定Zn2 、Ni2 ,方法简单、快速。 相似文献
11.
S. Viswanathan K. Surya Prakash Rao B. Mahabaleswar 《Journal of the Geological Society of India》2013,82(6):621-627
Komatiites are mantle-derived ultramafic volcanic rocks. Komatiites have been discovered in several States of India, notably in Karnataka. Studies on the distribution of trace-elements in the komatiites of India are very few. This paper proposes a simple, accurate, precise, rapid, and non-destructive wavelength-dispersive x-ray fluorescence (WDXRF) spectrometric technique for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in komatiites, and discusses the accuracy, precision, limits of detection, x-ray spectral-line interferences, inter-element effects, speed, advantages, and limitations of the technique. The accuracy of the technique is excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Zr, Nb, Ba, Pb, and Th and very good (within 4%) for Y. The precision is also excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th. The limits of detection are: 1 ppm for Sc and V; 2 ppm for Cr, Co, and Ni; 3 ppm for Cu, Zn, Rb, and Sr; 4 ppm for Y and Zr; 6 ppm for Nb; 10 ppm for Ba; 13 ppm for Pb; and 14 ppm for Th. The time taken for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in a batch of 24 samples of komatiites, for a replication of four analyses per sample, by one operator, using a manual WDXRF spectrometer, is only 60 hours. 相似文献
12.
奥地利安东帕有限公司 《岩矿测试》2009,28(3):306-306
最新的流行病学研究表明,空气中较高浓度的悬浮细颗粒可能对人类的健康有不利的影响。根据该项研究显示,由于心脏病、慢性呼吸问题和肺功能指标恶化而导致死亡率的升高与细尘粒子有关。这些研究结果已经促使欧盟于1999年4月出台了限制空气中二氧化硫、二氧化氮、氧化氮、铅和颗粒物含量的法案(1999/30/EC),对各项指标包括对可吸入PM10颗粒的浓度提出了新的限制性指标。PM10颗粒是指可以通过预分级器分离采集的气体动力学直径小于10μm的细颗粒。目前研究的兴趣重点逐步偏向PM2.5这些更细微颗粒物,PM2.5这种颗粒物对健康有明显的不利影响。在欧盟指令2008/50/EC中,对PM10和PM2.5都提 相似文献
13.
14.
E. M. Prasolov S. A. Sergeev B. V. Belyatsky E. S. Bogomolov K. A. Gruzdov I. N. Kapitonov R. Sh. Krymsky V. O. Khalenev 《Geochemistry International》2018,56(1):46-64
This paper reports the first results of a study of 11 isotope systems (3He/4He, 40Ar/36Ar, 34S/32S, 65Cu/63Cu, 62Ni/60Ni, 87Sr/86Sr, 143Nd/144Nd, 206–208Pb/204Pb, Hf–Nd, U–Pb, and Re–Os) in the rocks and ores of the Cu–Ni–PGE deposits of the Norilsk ore district. Almost all the results were obtained at the Center of Isotopic Research of the Karpinskii All-Russia Research Institute of Geology. The use of a number of independent genetic isotopic signatures and comprehensive isotopic knowledge provided a methodic basis for the interpretation of approximately 5000 isotopic analyses of various elements. The presence of materials from two sources, crust and mantle, was detected in the composition of the rocks and ores. The contribution of the crustal source is especially significant in the paleofluids (gas–liquid microinclusions) of the ore-forming medium. Crustal solutions were probably a transport medium during ore formation. Air argon is dominant in the ores, which indicates a connection between the paleofluids and the atmosphere. This suggests intense groundwater circulation during the crystallization of ore minerals. The age of the rocks and ores of the Norilsk deposits was determined. The stage of orebody formation is restricted to a narrow age interval of 250 ± 10 Ma. An isotopic criterion was proposed for the ore-bearing potential of mafic intrusions in the Norilsk–Taimyr region. It includes several interrelated isotopic ratios of various elements: He, Ar, S, and others. 相似文献
15.
Mining induced subsidence can significantly affect mining costs where major surface facilities and natural environment need to be protected. Overburden grout injection is a technology used to control coal mine subsidence by injecting the mine waste material extracted from the coal back into the inter-burden rock during longwall mining. The flowing slurry is here categorised as a nonlinear viscous cohesive (Bingham plastic) fluid. During longwall mining the grout slurry is pumped into the separated beds of the rock mass through a central vertical borehole, which is drilled deep into the inter-burden rock strata above the coal seam. However, a blockage can occur in the injection system when the slurry velocity falls below a certain critical threshold velocity, indicating a material phase change from cohesive-viscous to cohesive-frictional. In situ field injection tests through boreholes have been simulated at a smaller scale at the CSIRO laboratory in Brisbane by pumping the slurry through a radial disk (gap = 4 mm) from its centre. Laboratory experiments indicate a general, nonlinear, cohesive, viscous, frictional model for shear behaviour of the slurry, in which the material shear parameters are functions of the disk radial distance. Complete dimensional and dimensionless analytical solutions have been developed based on an approach related to Bingham–Herschel–Bulkley fluid mechanics. The derived formulae include relations for minimum pump pressure, local pressure and pressure gradient, wall shear stress, volume rate, velocity and velocity gradient. The theoretical results match the experimental measurements. The experiments covered slurries with maximum particle sizes of 0.5 to 2 mm with about 50% being larger than 100 µm. The viscosities at the various solids concentrations were measured with a standard torsion viscometer. This study differs from the previous research in several distinct aspects, namely, consideration of the variable shear parameters rather than fixed values, inclusion of total nonlinear behaviour, and implementation of a friction function to mimic behaviour of the deposited and consolidating stiff slurry, which can cause a significant pressure rise as a result of the increased shear resistance. 相似文献
16.
17.
Alexander E. C. Broberg J. S. Kehren A. R. Graziani M. M. Turri W. L. 《Environmental Geology》1993,22(4):353-361
Bellechester, Minnesota, is a small community of approximately 155 residents located on the county line between Goodhue and Wabasha counties in southeast Minnesota's karst region. Bellechester is served by a 21-year-old wastewater treatment facility (WWTF) consisting of three waste-stabilization ponds. On 28 April 1992 six sinkholes were discovered to have drained cell 2 of the WWTF resulting in the loss of approximately 8.7×106 1 of partially treated effluent and about 600 m3 of soil into previously undetected subsurface voids of unknown dimensions. In the week following the collapse, approximately 200 water wells located within a 5-km radius of the WWTF were sampled in an after-the-fact, emergency sampling program. Twelve samples with elevated fecal coliform levels, 18 samples with nitrate-nitrogen greater than the 10 mg/1 standard, and no samples with elevated chlorides were found. However, the elevated levels could not be unambiguously attributed to the WWTF collapse. This is the third WWTF to fail by sinkhole collapse in southeast Minnesota since 1974. All three collapsed lagoons have been located in similar geomorphic and stratigraphic settings. However, at least two lagoons have collapsed in the adjacent area in northeast Iowa, and these lagoons are located at different stratigraphic positions. Twenty-two WWTFs constructed in southeast Minnesota's karst region in the last 25 years have been identified as subject to potential sinkhole collapse. An unknown but significant number of manure storage lagoons, flood control structures, etc., have also been constructed in the karst region and are at risk. Public agencies are beginning to develop plans to deal with the risk associated with existing and future waste lagoons in this environment. The critical hydrogeologic parameters that can be used to prioritize the risk of collapse at existing facilities include: (1) the lithology of the first bedrock beneath each lagoon, (2) the thickness of surficial materials between the lagoon and the bedrock surface, (3) the presence and construction of liners (seepage rate), and (4) the proximity to existing sinkholes. 相似文献
18.
Mercury,arsenic, antimony,and selenium contents of sediment from the Kuskokwim River,Bethel, Alaska,USA 总被引：1，自引：0，他引：1
The Kuskokwim River at Bethel, Alaska, drains a major mercury-antimony metallogenic province in its upper reaches and tributaries. Bethel (population 4000) is situated on the Kuskokwim floodplain and also draws its water supply from wells located in river-deposited sediment. A boring through overbank and floodplain sediment has provided material to establish a baseline datum for sediment-hosted heavy metals. Mercury (total), arsenic, antimony, and selenium contents were determined; aluminum was also determined and used as normalizing factor. The contents of the heavy metals were relatively constant with depth and do not reflect any potential enrichment from upstream contaminant sources. 相似文献
19.
滇东南锡、银、铅、锌多金属矿床主要分布在个旧、白牛厂、都龙3个矿区,而滇东南较大的3个花岗岩体又分别出露在3个矿区或附近.花岗岩体均形成于燕山晚期,岩石化学、矿物成分相似,富含锡、银、铅、锌、钨、铜等成矿元素.矿床主金属元素组合与岩体之间的距离由远而近出现由锡、钨、(铍、铌、钽)→锡、钨、(铁)、铜、铟→锡、铅、锌、银、铟、(锑)有规律的变化.花岗岩浆是成矿物质来源和成矿热源.岩浆侵入初期使上覆地层隆起产生背斜(凹陷部位成向斜);同时使地层产生一系列裂隙、压性断层或层间断裂;岩浆侵入晚期,这些断层再次活动,表现为张性,岩浆产生的含矿热液沿由其活动所造成的断裂迁移、充填、交代、沉淀而形成矿床. 相似文献
20.
岩石密度和超高压岩石折返速率 总被引：1，自引：3，他引：1
在常温常压条件下对中国大陆科学钻CCSD主孔100-3000米岩心样品进行了密度测量,建立了密度连续剖面,并界定了不同超高压岩石的密度值。通过对比高温高压物性实验资料,岩石密度随着退变程度增强而降低,榴辉岩密度变化序列为3.52g/cm3→3.49g/cm3→3.07g/cm3→2.93g/cm3。超高压长英质岩石密度变化序列为3.00g/cm→2.80g/cm3→2.65g/cm3。上述实验资料是讨论不同折返阶段岩石所受浮力的基础,为研究折返速率大小提供了基本参数。本文通过折返板块运动平衡时,上浮力与粘滞力平衡这一关系式,定量研究了大陆俯冲板块的折返速率,认为密度差产生上浮力从而引起折返,温度对板块折返速率的影响最为显著;密度差大小、折返角度、折返板块大小对折返速率也有直接的影响。定量模拟分析表明,在温度高于850℃时,板块的折返速率可以超过100mm/a;当温度降至700℃时,折返速率则低于1.5mm/a。作者认为在折返早期,温度较高,板块快速折返至60-70km榴辉岩相深度;随着传导散热,温度降低,板块以较慢的速率折返至中下地壳。折返速率的估算表明,浮力是板块折返第一阶段(从>100km深部折返至<40km的中下地壳)的主要驱动力。 相似文献