共查询到20条相似文献，搜索用时 62 毫秒
1.
针对圆筒型海上储油装置FPSO垂荡运动性能较差、无法安装干式井口的问题,设计了带延伸筒体与矩形阻尼结构的圆筒型FPSO,根据延伸筒体与矩形阻尼结构是否通海分为两种型式。建立水动力计算模型,比较分析不同延伸筒体和阻尼结构型式对FPSO水动力性能的影响。针对南海作业海域,设计了悬链式系泊系统,基于JONSWAP波浪谱对FPSO的运动进行时域预报,并对系泊系统进行校核。分析结果表明:通海型FPSO垂荡固有周期显著提升,可以错开南海百年一遇谱峰周期,通海型FPSO满足钻井、安装干式井口的运动响应要求,系泊系统系缆张力满足规范要求。 相似文献
2.
3.
针对1 000 m水深作业的新型圆筒型浮式生产储卸油系统（FPSO）,选择多点系泊FPSO和穿梭油轮串靠外输方案,分析串靠方案在中国南海的可行性。FPSO和穿梭油轮作业时两者之间相互影响的研究较为重要,通过ANSYS-AQWA建立水动力耦合分析模型,基于多浮体水动力学方法进行时域耦合仿真模拟。在FPSO作业海况下,分析了串靠外输时系泊锚链及系泊大缆的张力特性和两浮体的运动响应,对大缆的长度和刚度参数变化进行了分析。结果表明：串靠外输方案满足新型圆筒型FPSO的作业环境。随着系泊大缆长度增加,其张力最值逐渐减小,FPSO和穿梭油轮的最小间距逐渐增大。两浮体最小距离稳定在83 m左右。随着系泊大缆刚度增加,其张力最值增大,相比于大缆长度,大缆刚度对耦合系统的影响较弱。 相似文献
4.
八角形FPSO串靠外输系统耦合动力响应分析 总被引：1，自引：0，他引：1
针对100 m作业水深的八角形FPSO,提出采用穿梭油轮串靠的外输方案,研究串靠外输在南海的适用性。建立由八角形FPSO及其系泊系统、穿梭油轮及FPSO与穿梭油轮之间的系泊大缆等组成的浮式多体动力学模型,根据多浮体动力学理论进行耦合时域模拟。在外输海况条件下,分析了串靠连接的环境适应性及研究大缆载荷的响应特性,对连接大缆的长度、刚度等关键参数进行了敏感性分析。研究表明,串靠外输的形式对于八角FPSO具有足够的安全性和可靠性,系泊大缆受到明显的冲击张力,张力的幅值受大缆的长度和刚度影响较大。 相似文献
5.
6.
针对FPSO软刚臂单点系泊系统出现过的系泊腿失效及背向工况风险事件,以渤海某16万吨级FPSO为例,采用数值模拟的方法,计算FPSO及单点系统在百年一遇海况下的载荷效应,通过统计学方法拟合效应的概率分布,完成定量风险分析。对于系泊腿旋转失效后的风险,使用故障假设(what-if)方法,依据失效后果判断其风险权重。计算结果表明,系泊腿结构在正常情况下受拉失效的概率很小;系泊腿纵摆失效后导致的结果比横摆失效更为严重,风险权重更大。背向工况下,船艏与YOKE的间距要明显小于顺向工况,在设计时增大二者间距可有效减小碰撞风险。 相似文献
7.
以KdV、eKdV和MCC理论的适用性条件为依据,利用内孤立波产生的瞬时速度和瞬时压力沿船体表面求面积分的方法分别计算浮式生产储油卸油装置(FPSO)内孤立波摩擦阻力和Froude-krylov力,再结合时域有限位移运动方程,研究了有限深两层流体中的内孤立波与带分段式系泊缆FPSO的相互作用问题。以东沙群岛某海域实测170 m振幅的内孤立波为对象,数值分析了在内孤立波作用下FPSO的内孤立波动态载荷、运动响应及其系泊张力的变化特性。研究表明,内孤立波会对FPSO产生突发的冲击,使FPSO产生大幅度水平漂移运动,导致系泊缆张力显著增大。在该振幅内孤立波作用下,FPSO受到的水平力最大可达56 t,垂向力最大可达1 961 t;纵荡位移可达47.62 m,系泊缆张力增加最大可达106.4 t。因此,在FPSO等深海浮式结构物的设计应用中,内孤立波的影响是不可忽视的。 相似文献
8.
9.
10.
浅海围网养殖是一种全新的海水生态养殖方式,敷设在开放性海域,承受风、浪和流的作用,产生复杂的水动力。本文根据养殖围网海上实际敷设情况和水文条件,基于松田皎模型准则设计制作了长方体、圆柱体和球体3种不同浮筒形状的浮绳式柔性框架养殖围网模型。在循环动水槽中采用预加张力的系泊方法测试了不同流速和系泊角度下围网框架纲和系泊缆绳的张力特征变化。研究结果显示:流速与张力的关联度大于系泊角度与张力的关联度;流速小于35cm/s时,系泊缆绳的张力变化较平稳;系泊角度在63°和74°之间时,系泊缆绳和框架纲张力的变化较平稳,且当系泊角度为71°时,张力相对较小;相比其他2种浮筒类型围网,长方体浮筒浮绳式框架养殖围网的系泊缆绳和框架纲张力的变化相对较平稳。 相似文献
11.
Chandralata Raghukumar G. Sheelu P. A. Loka Bharathi Shanta Nair C. Mohandass 《Marine Georesources & Geotechnology》2001,19(1):1-16
In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance. 相似文献
12.
海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。 相似文献
13.
Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification
An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm. 相似文献
14.
Derek V. Ellis 《Marine Georesources & Geotechnology》2001,19(1):51-63
This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested. 相似文献
15.
G. Parthiban 《Marine Georesources & Geotechnology》2000,18(3):223-235
Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement. 相似文献
16.
17.
18.
Phylogenetic diversity and phenotypic characterization of cultivable bacterioplankton isolated from polar oceans 总被引：1，自引：0，他引：1
A set of 27 marine planktonic bacteria isolated from the polar regions was characterized by 16S rDNA sequencing and physiological and biochemical testing. More than half of these bacteria were positive for caseinase, gelatinase and 13-glucosidase, and could utilize glucose, maltose or malic acid as carbon source for cell growth. Twelve isolates expressed nitrate reduction activities. Except for one antarctic isolate BSwlO175 belonging to Actinobacteria phylum, these isolates were classified as γ-Proteobacteria, suggesting that γ-Proteobacteria dominated in cultivable marine bacterioplankton at both poles. Genus Pseudoalteromonas was the predominant group in the Chukchi Sea and the Bering Sea, and genus ShewaneUa dominated in cultivable bacterioplankton in the Prydz Bay. With sequence similarities above 97%, genus Psychrobacter was found at both poles. These 27 isolates were psychrotolerant, and significant 16S rDNA sequence similarities were found not only between arctic and antarctic marine bacteria （ 〉 99% ）, but also between polar marine bacteria and bacteria from other aquatic environments （ ≥ 98.8% ）, including temperate ocean, deep sea, pond and lake, suggesting that in the polar oceans less temperature-sensitive bacteria may be cosmopolitan and have a bipolar, even global, distribution at the species level. 相似文献
19.
The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments. 相似文献
20.
Oedometer tests have been carried out on 70 undisturbed surficial clays (at approximately 250 mm below the mudline), mostly collected by free-fall corers from sites widely scattered throughout the deep-sea North Atlantic. Acoustic measurements were also made, initially on contiguous samples and ultimately on the same sample using a geophysically instrumented oedometer which also collected electrical resistivity data. Apart from those quiescent areas below the carbonate compensation depth, such as north of the West Indies where very fine clays exist, most of the samples are silty clays whose geotechnical-geophysical properties are dependent on the type of clay minerals present (and their ability to take in moisture), the sand-size fraction, and the quantity of carbonate present. Thus the pure clays have high compressibilities which decrease on the addition of coarse particles, while the converse is true for the acoustic parameters, these increasing with the sand fraction. Using the notion of the intrinsic compression line for all samples, and comparison to it of the measured compression curves, it is clear that, contrary to some previously held ideas, most deep-sea clays are normally consolidated; the addition of carbonate has the effect of creating an open, stronger sediment skeleton. Interestingly, where information is available, the variation with depth of a sample's acoustic velocity follows the void ratio pressure relationship of the compression curve. This allows the construction of an in-situ sediment compression curve using the in-situ geophysical observations. 相似文献