共查询到20条相似文献，搜索用时 51 毫秒
1.
海洋可控源电磁拖曳系统是海洋可控源电磁勘探系统的重要组成部分,对光电复合缆和绞车的强度有着较高的要求。为了保障作业安全,避免拖缆崩断、绞车损坏等事故的发生,需要对拖曳系统所受的张力进行评估,为实际作业提供参考。本文采用拖曳系统稳态运动求解方法,模拟拖体在海水中的位置,以及放缆时绞车所受的牵引张力,模拟结果与海试实测数据能够较好地吻合。在拖缆长度一定的情况下,随着拖曳速度的增大,绞车牵引张力先减小再增大,光电复合缆长度越长这种现象越明显。 相似文献
2.
采用集中质量法研究了绷紧式系泊系统中系缆由于松弛-张紧过程产生的冲击张力。建立系泊缆绳离散的集中质量模型,对其独立单元进行受力分析并建立了单元的运动方程。给定缆绳上端点简谐激励,通过Ansys中的Aqwa模块,分析了缆绳的运动响应;针对缆绳运动响应过程中的三种状态进行了模拟计算,探讨了冲击张力产生的条件;研究了缆绳初始预张力、上端点激励幅值和频率、拖曳力系数、弹性模量以及单位长度质量对动态张力的影响。研究结果表明:这些影响因素不仅会影响缆绳动态张力的大小,也会对缆绳中的冲击张力产生一定的影响。 相似文献
3.
拖曳绞车用于收放水下拖体,是保障水下拖曳系统正常工作的重要装置。参照 BV043 和 GJB1060 标准确定其冲击环境,利用 ABAQUS 有限元软件,采用时域分析方法对拖曳绞车进行有限元计算分析,校核拖曳绞车在受到垂向、横向、纵向 3 个方向冲击载荷作用时的强度。结果表明：拖曳绞车结构所受应力在许用应力范围以内,满足规范抗冲击准则,但不同冲击方向下,最大应力位置不同;安装位置不同,绞车子设备加速度响应规律差异很大,固定安装于支架的控制柜和液压阀组衰减规律明显,悬挂安装的防松马达不易进入稳定状态。 相似文献
4.
5.
TLP平台张力腿安装方法有竖直安装和水平安装。以一TLP平台张力腿为例,基于张力腿水平湿拖安装方法,采用OrcaFlex软件建立扶正分析模型,数值模拟了张力腿现场扶正过程,研究分析了张力腿在不同海洋环境和吊机缆绳释放速度等参数下的动力响应,并在此基础上进行了集束扶正分析,根据安装接受标准确定了合适的扶正作业天气窗口。模拟分析结果表明:在扶正过程中,浪向/流向、波高、流速对张力腿应力影响显著;吊机缆绳张力对浪向/流向、流速敏感;吊机缆绳释放速度对张力腿应力和吊机缆绳张力影响微弱。 相似文献
6.
针对应用于中国南海的新型深水Spar钻井生产储卸油平台进行了涡激运动特性与影响的研究。对该平台进行涡激运动拖曳试验,根据规范和动力学分析得出平台的拖曳力系数和升力系数,通过比较南海流速分布情况与平台涡激运动与流速关系发现:该平台在一般海况下即可发生幅值为10 m左右的涡激运动;对平台进行水池模型试验,进一步验证涡激运动拖曳试验结果并分析平台运动性能,对平台受到的脉冲拖曳力和升力载荷进行了初步校验。通过模型试验对平台涡激运动特性有了初步认识,发现在百年一遇条件下,平台脉动拖曳力载荷与升力载荷比为1∶3;一年一遇条件下,平台脉动拖曳力载荷与升力载荷比为1∶1。根据试验结果对数值模型进行了修正并与试验值进行比较,比较结果表明经过修正后的计算结果与试验结果取得了良好的一致性。比较了全尺度下涡激运动对于平台系泊系统和平台水平位移的影响,结果表明:涡激运动的存在使得Inline方向系泊张力增加5%,并使得系泊缆受力分布产生变化,位移增加27%;Between line方向张力增加15%,位移增加2.5%。涡激运动对于平台极限张力以及极限漂移出现方向还有待进一步研究。涡激运动对于平台系泊系统疲劳寿命的影响还需进一步研究。 相似文献
7.
以浅水单点系泊装置水下软钢臂维修解脱为背景,研究在拖轮限位状态下FPSO运动与限位缆绳张力。计算在不同水深及浪向条件下,FPSO的二阶传递函数(QTF);分别应用Newman近似方法、全QTF法以及使用部分QTF值的方法,计算FPSO时域低频波浪载荷,并对其限位响应进行对比;计算不同长度时的限位缆绳张力响应,分析限位缆绳长度及FPSO波频运动对缆绳张力的影响。分析表明:Newman近似的适用性,应根据FPSO的QTF与海浪谱能量集中范围综合判断;为减少QTF计算量,可根据FPSO低频运动固有频率,确定频率间隔△ω的计算上限,采用部分QTF值计算低频波浪载荷,其响应预报结果与全QTF法接近;若FPSO的RAO能够避开海浪谱能量集中的频率范围,则在限位分析中可忽略FPSO波频运动的影响。 相似文献
8.
拖曳锚由于其承载性能和深水中便于安装被广泛应用于海洋工程系泊系统中,如:适用于悬链式系泊系统的传统拖曳锚和适用于绷紧式系泊系统的法向承力锚。拖曳锚安装过程中涉及诸多运动特性:锚板运动方向、系缆点处拖曳力和拖曳角及运动轨迹。基于大变形有限元分析技术耦合的欧拉-拉格朗日法,并引入缆绳方程,建立起锚-缆绳-海床土耦合作用的有限元分析模型;模拟了拖曳锚在均质和线性强度黏土中的嵌入安装过程,研究了锚板运动方向、系缆点处拖曳力和拖曳角及运动轨迹等运动特性;通过与已有的有限元分析方法及理论方法进行对比,验证了该分析模型的有效性;与已有的有限元分析方法相比,提出的分析模型有效地提高了计算效率。 相似文献
9.
10.
海洋地震拖缆是海洋油气资源勘探中的关键设备,为研究海洋地震拖缆的动力特性及其在不同频率正弦激励干扰下的动力响应,建立了零浮力拖缆的数学模型,设计了一套完整的实验方案,通过弹性测力机构放大张力信号以排除环境干扰,测量了不同拖曳速度与激振频率条件下拖缆首部的张力变化及缆上位移响应情况,初步分析了正弦激励作用下零浮力拖缆的动力学响应。弹性测力机构具有良好的线性度与可重复性,拖缆受到的水阻力与拖曳速度的平方成正比,数值计算与实验结果对比验证了数学模型的正确性,初步分析了正弦激励作用下零浮力拖缆的动力学响应。 相似文献
11.
Chandralata Raghukumar G. Sheelu P. A. Loka Bharathi Shanta Nair C. Mohandass 《Marine Georesources & Geotechnology》2001,19(1):1-16
In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance. 相似文献
12.
Arne Schnack-Friedrichsen Angela M. Davis Jim D. Bennell Dei G. Huws 《Marine Georesources & Geotechnology》2001,19(4):221-243
The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths. 相似文献
13.
Derek V. Ellis 《Marine Georesources & Geotechnology》2001,19(1):51-63
This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested. 相似文献
14.
G. Parthiban 《Marine Georesources & Geotechnology》2000,18(3):223-235
Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement. 相似文献
15.
Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification
An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm. 相似文献
16.
海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。 相似文献
17.
The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments. 相似文献
18.
Shigehisa Nakamura 《Marine Geodesy》2000,23(1):55-61
Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone. 相似文献
19.
The effect of different fixation and storage protocols on the flow cytometric (FCM) simultaneous analysis of bacterioplankton and phytoplankton in coastal seawater samples (Mediterranean coastal lagoons) was investigated. FCM measurements (cell number, fluorescence and scatter characteristics) were obtained through DAPI staining. Three fixatives [glutaraldehyde (GA), formaldehyde (FA) and paraformaldehyde (PFA)] and two storage (3 months duration) methods (5 °C and −196 °C) were tested. Two dominant populations were detected in studied samples: bacteria and eukaryotic picophytoplankton. Adding fixatives (2% final concentration) appears necessary to obtain FCM exhaustive counts of all the bacteria and phytoplanktonic cells. This was related to the permeation effect of fixatives which allowed a better DAPI staining of the cells. Maximum fluorescence, i.e. optimal staining of the cells was obtained with FA or PFA, and significant lower fluorescences with GA. Fixed samples stored at 5 °C induced rapid cell loss. Only storage in liquid nitrogen of samples fixed with FA or PFA, allows mid-term (≥4 months) preservation of bacteria or picophytoplankton cell numbers, and limited evolution of DAPI-induced fluorescence and scatter characteristics. 相似文献
20.