共查询到20条相似文献，搜索用时 843 毫秒
1.
A joint surface roughness/volumetric perturbation scattering theory is utilized to characterize the reverberation from a littoral ocean bottom. The result is a reflected field spectrum that consists of specular and off-specular components. The predicted scattering strength from the off-specular component is shown to be comprised of interface roughness scattering, sediment inhomogeneity volumetric scattering, and interface roughness/sediment inhomogeneity correlation scattering. The sediment inhomogeneity volumetric scattering is shown to contain two contributions that are due to fractional variations in sediment densities and sound velocities. Both contributions are shown to be affected by the interface effect by a round-trip transmission coefficient factor. These two fractional variations are shown to contribute differently to scattering strength but similarly to backscattering strength. Inversely predicted roughness spectra from various sets of backscattering strength data are shown to be consistent with a generally known roughness spectrum. Both inversely predicted roughness and volumetric scattering physical property spectra are found to be self-consistent. However, the use of only ocean bottom backscattering strength data is found to be insufficient to judge whether the roughness or the volumetric scattering dominates. Reverberation characterizations using bistatic scattering strength data and signal spread data are planned for future studies 相似文献
2.
Monostatic reverberation measurements were collected in shallow water, over a coarse gravel and cobble bottom, 100 m deep, off the coast of Nova Scotia. Data were collected at frequencies of 21, 28, and 36 kHz using linear FM pulses of 2-kHz bandwidth and 0.160-s duration. An anchored, high-frequency active sonar array deployed at a depth of 42 m was used to collect the data. The reverberation measurements were compared with estimates computed with the NUWC generic sonar model (GSM). The data were reasonably well modeled for times greater than 0.2 s after pulse transmission by neglecting surface reverberation and using Lambert's rule for bottom backscattering with a scattering coefficient of -27 dB, independent of frequency. At all three frequencies, the data and model show a peak approximately 0.9 s after pulse transmission. This peak results from a focusing effect that the downward-refracting sound-speed profile has on the interaction of the rays with the bottom 相似文献
3.
《Oceanic Engineering, IEEE Journal of》2009,34(1):51-62
4.
Reverberation measurements made by the SACLANT Undersea Research Centre at three shallow-water sites (130-190-m depth) are compared with each other and with estimates from the DREA normal-mode reverberation model OGOPOGO. The experiments over silt-clay and sand seabeds were conducted at slightly bistatic geometries (0.7-6.0-km source-receiver separation), using explosive sources detonated at mid-water depths. The signals were received on hydrophones of either a vertical or horizontal array and analyzed in one-tenth-decade frequency bands from 25 to 1000 Hz. The data are compared with each other to investigate the site differences and frequency dependencies, and with the estimates from the reverberation model OGOPOGO to interpret the data and to obtain a qualitative measure of the scattering. For modeling purposes, geoacoustic models of the seabed were assumed, and the reverberation data were fitted by adjusting the Lambert bottom scattering coefficients. Good model agreement was obtained with both individual hydrophone and data. Though somewhat sensitive to the geoacoustic the Lambert coefficients give a measure of the frequency dependence of the scattering. For the silt-clay bottom, the scattering is weak but is independent of frequency; for the sand bottoms, the scattering is stronger and increases with frequency. These results are compared with estimates from other experiments 相似文献
5.
Cable P.G. Yudichak T.W. Dorfman Y. Knobles D.P. Renhe Zhang Zhaohui Peng Fenghua Li Zhenglin Li 《Oceanic Engineering, IEEE Journal of》2006,31(1):145-155
Determinations of bottom scattering strength in the decade below 1 kHz under downward refracting conditions have been made using acoustic reverberation and transmission data from the 2001 East China Sea Asian Seas International Acoustic Experiment (ASIAEX). The measurements were performed using explosive sources and receiving hydrophones in ship-suspended vertical-line arrays. The focus of this paper has been the dependence of bottom scattering strength on the frequency and characterization of the uncertainties associated with the extraction of scattering strength from reverberation. The derived bottom scattering strength gradually rises with frequency from 100-300 Hz and then more rapidly above 300 Hz. A potential explanation suggests that the frequency variation results from two scattering mechanisms, rough layer scattering at the low end of the band and sediment near-surface volume scattering at the high end. The spatial extrapolation of these results is explored by comparing them with similarly derived scattering strengths using data obtained under the Navy's Harsh Environments Program at a somewhat separated site (56 km) under environmental conditions similar to those during ASIAEX. In the ASIAEX analysis, it has been found that the largest source of uncertainty in the scattering-strength frequency dependence arises from persistence of finite-amplitude effects associated with the source signal. 相似文献
6.
一种分层海底反向散射模型 总被引：1，自引：1，他引：0
In order to predict the bottom backscattering strength more accurately, the stratified structure of the seafloor is considered. The seafloor is viewed as an elastic half-space basement covered by a fluid sediment layer with finite thickness. On the basis of calculating acoustic field in the water, the sediment layer, and the basement, four kinds of scattering mechanisms are taken into account, including roughness scattering from the water-sediment interface, volume scattering from the sediment layer, roughness scattering from the sediment-basement interface,and volume scattering from the basement. Then a backscattering model for a stratified seafloor applying to low frequency(0.1–10 kHz) is established. The simulation results show that the roughness scattering from the sediment-basement interface and the volume scattering from the basement are more prominent at relative low frequency(below 1.0 kHz). While with the increase of the frequency, the contribution of them to total bottom scattering gradually becomes weak. And the results ultimately approach to the predictions of the high-frequency(10–100 kHz) bottom scattering model. When the sound speed and attenuation of the shear wave in the basement gradually decrease, the prediction of the model tends to that of the full fluid model, which validates the backscattering model for the stratified seafloor in another aspect. 相似文献
7.
A two-scale roughness model for bottom backscattering (Novarini and Caruthers) was applied to multibeam sounder data (95 kHz) from Browns Bank (south of Yarmouth, Nova Scotia, Canada). In order to better understand frequency and incident angle dependence of backscattering, acoustic-calibration data (1-6 kHz) were collected from the same area and treated with the same model. The frequency and incident angle dependence of bottom backscattering in the multibeam and acoustic-calibration data were compared. Backscattering due to large-scale roughness was most relevant at near-normal incidence (<7°) and it was more dominant in the low-frequency range, and was strongly dependent on incident angle. Volume scattering was least dependent upon incident angle. It was the dominant factor at the large incident angle. Bragg scattering was the most significant over a very wide frequency range and was more important for high frequency (>5 kHz) and small incidence, but not near-normal incidence 相似文献
8.
Tests of models for high-frequency seafloor backscatter 总被引：3，自引：0，他引：3
Jackson D.R. Briggs K.B. Williams K.L. Richardson M.D. 《Oceanic Engineering, IEEE Journal of》1996,21(4):458-470
The interaction of high-frequency sound with the seafloor is inherently a stochastic process. Inversion techniques must, therefore employ good stochastic models for bottom acoustic scattering. An assortment of physical models for bottom backscattering strength is tested by comparison with scattering strength data obtained at 40 kHz at three shallow water sites spanning a range of sediment types from fine silt to coarse sand. These acoustic data are accompanied by sediment physical property data obtained by core sample analysis and in situ probes. In addition, stereo photography was used to measure the power spectrum of bottom relief on centimeter scales. These physical data provided the inputs needed to test the backscatter models, which treat scattering from both the rough sediment-water interface and the sediment volume. For the three sites considered here, the perturbation model for scattering from a slightly rough fluid seafloor performs well. Volume scattering is predicted to be weak except at a site having a layer of methane bubbles 相似文献
9.
Current models used to predict the backscattering strength of the ocean floor are either very involved, requiring geoacoustic parameters usually unavailable for the site in practical applications, or overly simplistic, relying mainly on empirical terms such as Lambert's law. In any case, solutions are very approximate and the problem is still far from being solved. In this paper, a model is presented that avoids empirical functional forms yet requires only a few physical parameters to describe the surficial sediments, often tabulated for typical sediments. The aim of this paper is to develop a simple algorithm for operational prediction of bottom reverberation with only one free parameter, i.e., the volume scattering coefficient. The algorithm combines a two scale surface scattering model with scattered contributions originating from inhomogeneities within the sediments, talking into consideration the rough interface. No specific mechanism is assumed for scattering at the volume inhomogeneities; however, the inhomogeneities are assumed to be uniform and isotropic. The volume scattering coefficient, combined with the bottom attenuation and density and referenced to the surface, plays a role similar to the Lambert's constant in empirical models. The model is exercised on a variety of published datasets for low and moderately high frequency. In general, the model performs very well for both fast and slow sediments, showing a definite improvement over Lambert's law 相似文献
10.
Modeling Propagation and Reverberation Sensitivity to Oceanographic and Seabed Variability 总被引：1，自引：0，他引：1
《Oceanic Engineering, IEEE Journal of》2006,31(2):402-412
The propagation of bottom and oceanographic variability through to the variability of acoustic transmissions and reverberation is evaluated with a simple adiabatic model interacting with Gaussian distributed uncertainty in a narrow frequency band. Results show that there is significant sensitivity of time series and reverberation uncertainty to different types of environmental uncertainty. For propagation over uncertain bottoms, it is shown that it is that later part of the time series, corresponding to the highest angle energy reflecting most often off the surface and bottom, that is most sensitive to bottom uncertainty. This implies that the larger reverberation contributions from the highest grazing angles with the largest scattering strength is also the most uncertain. Conversely, it is the lowest angle arrivals which are most sensitive to uncertainty in the sound-speed profile. These behaviors are predicted analytically by the theory [K.D. LePage, in “Impact of Littoral Environmental Variability on Acoustic Predictions and Sonar Performance,” Kluwer, 2002, pp. 353-360]. 相似文献
11.
Ji-Xun Zhou Xue-Zhen Zhang 《Oceanic Engineering, IEEE Journal of》2005,30(4):832-842
A quality database of reverberation is absolutely essential if one is to understand the shallow-water reverberation problem. However, to get wideband reverberation levels (RL) simultaneously for both short and long ranges at low- and mid-frequencies is a delicate task that can be subject to errors. This paper introduces a simple method to get RL for the Asian Sea International Acoustics Experiment in the East China Sea (ASIAEX01). Special attention is paid to the measurements of the RL at short- and mid-ranges. With this method, one does not need to accurately calibrate hydrophones and measurement systems, or to measure absolute source level (SL). It can avoid signal overflow and saturation problems caused by powerful sound sources. The RL (relative to SL) at 1 s (or at 2 s) after an explosive source is detonated is defined as the initial reference reverberation level (IRRL). The IRRLs from four sites with different sandy sediments and different water depths have been given as a function of frequency in the 150-2500 Hz range. A mathematical model gives a physical explanation of the measured IRRL data. The resultant RL and IRRL may offer some reference values for the design of reverberation measurements or numerical simulations of shallow-water reverberation and bottom scattering. 相似文献
12.
High-frequency bistatic sediment scattering experiment was conducted in the shallow waters off the east coasts of Korea. Acoustic data were taken as a function of grazing angle (30°, 45°, and 60°), scattered angle (30°, 45°, and 60°), and bistatic (azimuthal) angle (0°, 60°, and 120°). Besides a flat bottom it was artificially raked so as to produce directional ripples. The measured scattering strengths for a flat bottom were compared to model predictions of D.R. Jackson et al. (1986). The surface reverberation component is seen to dominate over the volume scattering part at the frequency of 240 kHz. Compared to the flat bottom case, the scattering strengths for directional ripples showed lower and higher variation depending on the ripple's orientation 相似文献
13.
Discussed in this paper is the deep scattering layer (DSL) observed during the experiment in the South China Sea in October 1983. The authors have investigated the acoustic characteristics of the DSL, such as the volume scattering strength of the water column, the thickness of the layer and the coefficient of the backscattering. Resonant scattering, presumably caused by the swimbladder of fishes, is responsible for the bulk of observed reverberation. In addition, the size of the swimbladder forming the acoustic scatter of the DSL is also estimated. 相似文献
14.
Cable P.G. Frech K.D. O'Connor J.C. Steele J.M. 《Oceanic Engineering, IEEE Journal of》1997,22(3):534-540
Determinations of acoustic scattering strength for sand bottoms have been made at several different shallow-water areas under downward refracting sound propagation conditions in the frequency decade below 1 kHz. The measurements have been made using explosive sources detonated at mid-water depth and bottom-mounted vertical and horizontal hydrophone line arrays as receivers. The ubiquitous presence of multipaths in shallow water prevents a direct-path scattering geometry, and scattering strength must be extracted from the full reverberation field, which complicates the determination of bottom grazing angle dependence of scattering. The major focus of this paper has been the variation of scattering strength with frequency (integrated over participating bottom angles), though estimates of the angular dependence of scattering strength have been made using the vertical receiving array. Typically the integrated scattering strength for sand bottoms reported (and elsewhere) are found to decrease below 1 kHz and in some instances to exhibit a minimum in the several hundred hertz range. Sand bottom scattering strengths below 1 kHz are significantly lower than those predicted by the Mackenzie formula and the limited angular dependence determinations have been found to be consistent with Lambert's law 相似文献
15.
浅海均匀层远程混响的垂直相干性 总被引：1，自引：0，他引：1
混响是主动声纳在浅海环境中的一种干扰,有关其空间相关特性,Urick和Lund发表了两篇实验性报告[7].本文根据浅海平均声场角度谱分析法[3],从理论上计算了浅海均匀层远程混响垂直相关特性与界面反射、散射等环境参数之间的关系,及其随距离、水听器间隔的变化,供声纳设计或在浅海环境中研究低频、小掠角的散射特性时参考. 相似文献
16.
An oceanic reverberation model 总被引：1，自引：0，他引：1
A simple model of the surface, volume, and bottom reverberation received by a moving platform as a function of time following the tranmission of a narrow-band pulsed signal is described. Both the time-varying power level and the underlying power spectrum are predicted. The model includes the effects of platform motion, transmit signal windowing, transmit and receive beam patterns, and the environment (surface, volume, and bottom backscattering strengths, the scatterer velocity distributions for surface waves and current layers, and sound absorption). An isospeed sound speed profile is assumed and reflections at the surface and bottom boundaries are not permitted. Also described is a matched filter-envelope detector receiver model for post processing of the reverberation spectra. 相似文献
17.
An accurate model of acoustic interaction with sandy sediments is crucial to the application of SONAR in shallow-water environments. Because acoustic scattering from interface roughness plays a major role in the reverberation from and penetration into sandy sediments, it is imperative to be able to accurately measure the roughness of the sediment/water interface. An interface roughness measurement system has been developed in which a laser light sheet is projected onto the ocean floor. A resulting image can then be analyzed to determine the interface roughness. The system has been shown to achieve a height measurement error of less than 0.9 mm over a spatial frequency range of 15 to 60 cycles/m with about 0.5 mm standard deviation. These spatial frequencies correspond to acoustic Bragg frequencies of 11 to 45 kHz for backscattering applications. The error in wavelength was less than 5 mm with a standard deviation of about 1.0 mm. The system is inexpensive, easily deployable and automated in terms of data extraction. This system could greatly aid in determining the local interface profile for in situ acoustic scattering experiments. 相似文献
18.
Ji-Xun Zhou Xue-Zhen Zhang Rogers P.H. Simmen J.A. Dahl P.H. Guoliang Jin Zhaohui Peng 《Oceanic Engineering, IEEE Journal of》2004,29(4):988-999
Optimal array-processing techniques in the ocean often require knowledge of the spatial coherence of the reverberation. A mathematical model is derived for the reverberation vertical coherence (RVC) in shallow water (SW). A method for analysis of RVC data is introduced. Measured reverberation cross-correlation coefficients as a function of time and frequency, obtained during the Asian Seas International Acoustic Experiment (ASIAEX) in the East China Sea, are reported. SW reverberation from a single shot provides a continuous spatial sampling of the surrounding sound field up to several tens of kilometers and holds valuable information on the geoacoustic properties of the sea floor over this distance. SW reverberation data can, therefore, be used as the basis for a quick and inexpensive method for geoacoustic inversion and has the obvious advantage that acquiring the data in situ requires only a single platform. This paper considers the use of the vertical coherence of the reverberation as the starting point for such an inversion. Sound speed and attenuation in the sea bottom at the ASIAEX site are obtained over a frequency range of 100-1500 Hz by finding values that provide the best match between the measured and predicted RVC. 相似文献
19.
A model for numerical simulation of nonstationary sonar reverberation using linear spectral prediction 总被引：1，自引：0，他引：1
An innovative approach to the numerical generation of nonstationery reverberation time series is presented and demonstrated. The computer simulated reverberation time series are of high quality, in that they are accurate representations of those which would result from an actual sonar system (transmit/receive and horizontal/ vertical beampatterns; pulse type, shape, length, and power; frequency and sampling rate), platform (speed and depth), and environment (wind speed and direction, backscattering strengths, and propagation loss). Volume, surface, and/or bottom reverberation as seen by a multiple beam sonar on a moving platform is generated. The approach utilizes recent developments in linear spectral prediction research in which the spectra of stochastic processes are modeled as rational functions and algorithms are used to efficiently compute optimal estimates of coefficients which specify the spectra. A two-fold sequence is formulated; first, the expected reverberation spectra for all beams are predicted and, second, the stochastic time series are generated from the expected spectra. The expected spectra are predicted using a numerical implementation, referred to as the REVSPEC (reverberation spectrum) model, of a general formulation of Faure, Ol'shevskii, and Middleton. Given the spectra, the Levinson-Durbin method is used to solve the Yule-Walker equations of the autoregressive formulation of linear spectral prediction. The numerical implementation of the approach, referred to as the REVSIM (reverberation simulation) model, produces nonstationary coherent multiple-beam reverberation time series. The formulation of the REVSIM model is presented and typical results given. A comparison is made between the simulation outputs of the REVSIM model and those of the REVGEN (reverberation generator) model, a standard well-accepted time series simulation model, to demonstrate the validity of the new approach. 相似文献
20.
Experimental measurements of the bottom backscattering strength from carbonate sediments were made with a 200-kHz multibeam
sonar mounted on a remotely operated vehicle. Results were obtained from eight different sites, which may be grouped into
three categories, labeled soft, medium and hard, according to measured sediment sound speed. Sediment samples were gathered
at or near each site to help interpret the acoustic results. The acoustic results are compared with extant published data
and with the BOGGART bottom backscatter model. Backscattering strength values measured in the soft and medium sites fell within
the main cluster of previously published values from sediments of similar grain sizes. The values from the hard region fell
close to the upper limit. Dependence of the apparent backscattering strength on sonar height above bottom, particularly for
the lower values of height above bottom, was observed, which suggests that the scattering process is a multiple-scattering
one. 相似文献