共查询到20条相似文献，搜索用时 31 毫秒
1.
在南黄海某一典型的砂质海底区域，采用全向性声源和全向性接收水听器开展了频率范围为6-24 kHz的海底反向声散射测量。测量结果表明，在避免海面散射干扰并满足远场条件的情况下，本次实验获得了掠射角范围为18~80°的海底反向声散射强度，其数值为-41.1~24.4 dB。在有效掠射角范围内，声散射强度总体上随掠射角的增大呈现出增大趋势，但对于不同的频率，其变化趋势有所不同，反映出不同的散射机理。在20°、40°和60°掠射角处，在6-24 kHz的频率范围内反向声散射强度总体上呈现出正相关的频率依赖性，其线性相关斜率分别为0.2229 dB/kHz、0.5130 dB/kHz、0.1746 dB/kHz。在最大掠射角80°处，反向声散射强度未呈现出明显的频率相关性。 相似文献
2.
Acoustic backscattering from a sandy seabed was measured at a frequency of 5.5 kHz at a wide range of grazing angles. The measurement system used was the University of Miami's sonar tower, consisting of an omni-directional broadband source and two 16-channel hydrophone receiver arrays. A volume scattering model, which combines a fluid model with reflection/transmission coefficients derived from the Biot theory, is used. This model allows energy penetration into the bottom, calculations of the volume scattering at all grazing angles, and the frequency dependence of the sound speed in the water-saturated sediment. In the model, rather than assume sound-speed correlation length in sedimentary volume, core data were used to assimilate a 3-D fluctuation spectrum of the density. The numerical results showed excellent agreement with the measurement at lower grazing angles. We concluded that the interface roughness scattering was dominant at lower grazing angles, while the volume scattering is dominant at higher grazing angles at the sandy site. The border of the dominance of the interface and volume scattering was the so-called critical angle at this frequency. The frequency dependence of sound speeds is also discussed. 相似文献
3.
Acoustic backscattering experiments in a well characterized sand sediment: data/model comparisons using sediment fluid and Biot models 总被引：2，自引：0，他引：2
Williams K.L. Jackson D.R. Thorsos E.I. Dajun Tang Briggs K.B. 《Oceanic Engineering, IEEE Journal of》2002,27(3):376-387
As part of the sediment acoustics experiment 1999 (SAX99), backscattering from a sand sediment was measured in the 20- to 300-kHz range for incident grazing angles from 10/spl deg/ to 40/spl deg/. Measured backscattering strengths are compared to three different scattering models: a fluid model that uses the mass density of the sediment in determining backscattering, a poroelastic model based on Biot theory and an "effective density" fluid model derived from Biot theory. These comparisons rely heavily on the extensive environmental characterization carried out during SAX99. This environmental characterization is most complete at spatial scales relevant to acoustic frequencies from 20 to 50 kHz. Model/data comparisons lead to the conclusions that rough surface scattering is the dominant scattering mechanism in the 20-50-kHz frequency range and that the Biot and effective density fluid models are more accurate than the fluid model in predicting the measured scattering strengths. For 50-150 kHz, rough surface scattering strengths predicted by the Biot and effective density fluid models agree well with the data for grazing angles below the critical angle of the sediment (about 30/spl deg/) but above the critical angle the trends of the models and the data differ. At 300 kHz, data/model comparisons indicate that the dominant scattering mechanism may no longer be rough surface scattering. 相似文献
4.
一种分层海底反向散射模型 总被引：1，自引：1，他引：0
In order to predict the bottom backscattering strength more accurately, the stratified structure of the seafloor is considered. The seafloor is viewed as an elastic half-space basement covered by a fluid sediment layer with finite thickness. On the basis of calculating acoustic field in the water, the sediment layer, and the basement, four kinds of scattering mechanisms are taken into account, including roughness scattering from the water-sediment interface, volume scattering from the sediment layer, roughness scattering from the sediment-basement interface,and volume scattering from the basement. Then a backscattering model for a stratified seafloor applying to low frequency(0.1–10 kHz) is established. The simulation results show that the roughness scattering from the sediment-basement interface and the volume scattering from the basement are more prominent at relative low frequency(below 1.0 kHz). While with the increase of the frequency, the contribution of them to total bottom scattering gradually becomes weak. And the results ultimately approach to the predictions of the high-frequency(10–100 kHz) bottom scattering model. When the sound speed and attenuation of the shear wave in the basement gradually decrease, the prediction of the model tends to that of the full fluid model, which validates the backscattering model for the stratified seafloor in another aspect. 相似文献
5.
Sea-surface acoustic backscattering measurements at moderate to high frequencies were performed in the shallow water of the south Yellow Sea, using omnidirectional spherical sources and omnidirectional hydrophones. Sea-surface backscattering data for frequencies in the 6–25 k Hz range and wind speeds of(3.0±0.5)and(4.5±1.0) m/s were obtained from two adjacent experimental sites, respectively. Computation of sea-surface backscattering strength using bistatic transducer is described. Finally, we calculated sea-surface backscattering strengths at grazing angles in the range of 16°–85°. We find that the measured backscattering strengths agree reasonably well with those predicted by using second order small-roughness perturbation approximation method with "PM" roughness spectrum for all frequencies at grazing angles ranged from 40° to 80°. The backscattering strengths varied slightly at grazing angles of 16°–40°, and were much stronger than roughness scattering. It is speculated that scattering from bubbles dominates the backscattering strengths at high wind speeds and small grazing angles. At the same frequencies and moderate to high grazing angles, the results show that the backscattering strengths at a wind speed of(4.5±1.0) m/s were approximately 5 d B higher than those at a wind speed of(3.0±0.5) m/s. However, the discrepancies of backscattering strength at low grazing angles were more than 10 d B. Furthermore the backscattering strengths exhibited no significant frequency dependence at 3 m/s wind speed. At a wind speed of 4.5 m/s, the scattering strengths increased at low grazing angles but decreased at high grazing angles with increasing grazing angle. 相似文献
6.
In this paper, the lowest order small-slope approximation (SSA) scattering cross section for Biot theory is derived. Numerical results are obtained for both backscattering and bistatic scattering using a modified power law spectrum, and these results are compared with those of lowest order perturbation theory (PT). Frequencies ranging from 100 Hz to 3 kHz are used for surfaces with RMS heights h of 0.1 and 1 m and a correlation length l of 10 m. The angle of incidence for the bistatic results is limited to 45/spl deg/. It is found that for the smaller surface height roughness (h = 0.1 m), the SSA and PT give the same results for frequencies up to almost 1 kHz for both backscattering and bistatic scattering. For h = 1 m, the SSA and PT backscatter results are in good agreement at all frequencies for incident grazing angles up to approximately 45/spl deg/. For the bistatic results, the SSA and PT results agree only at low grazing angles of scatter. In the specular region, the results differ significantly. 相似文献
7.
Broad-band forward loss and backscattering measurements were made at low to moderate grazing angles in shallow water off San Diego using pulses extending from 1 to 6 kHz in bandwidth. For forward bounce measurements, these large bandwidths achieved time resolutions as small as 0.25 ms, and revealed fine-scale subbottom layering with separations down to approximately 50 cm. The forward loss values show large fluctuations (>10 dB) over translation distances of 20-50 m in some cases or between two measurement runs separated by a few hundred meters in other cases. This observation, along with associated variations in the extent and number of subbottom arrivals, indicates a distinct patchiness in surficial sediment type. Previous measurements made in nearby locales also evidenced strong variations in bottom loss, but lacked the spatial resolution to discern interface reflections from subbottom contributions. Broad-band backscattering strength measured at 20-40° grazing was quite homogeneous over the entire region, probably because the critical angle is below 20°, as inferred from forward loss measurements. Theory suggests that scattering at angles above critical is from subbottom inhomogeneities rather than boundary roughness. The grazing angle and frequency dependence of these backscattering data are relatively weak 相似文献
8.
Cable P.G. Frech K.D. O'Connor J.C. Steele J.M. 《Oceanic Engineering, IEEE Journal of》1997,22(3):534-540
Determinations of acoustic scattering strength for sand bottoms have been made at several different shallow-water areas under downward refracting sound propagation conditions in the frequency decade below 1 kHz. The measurements have been made using explosive sources detonated at mid-water depth and bottom-mounted vertical and horizontal hydrophone line arrays as receivers. The ubiquitous presence of multipaths in shallow water prevents a direct-path scattering geometry, and scattering strength must be extracted from the full reverberation field, which complicates the determination of bottom grazing angle dependence of scattering. The major focus of this paper has been the variation of scattering strength with frequency (integrated over participating bottom angles), though estimates of the angular dependence of scattering strength have been made using the vertical receiving array. Typically the integrated scattering strength for sand bottoms reported (and elsewhere) are found to decrease below 1 kHz and in some instances to exhibit a minimum in the several hundred hertz range. Sand bottom scattering strengths below 1 kHz are significantly lower than those predicted by the Mackenzie formula and the limited angular dependence determinations have been found to be consistent with Lambert's law 相似文献
9.
Backscattering from bioturbated sediments at very high frequency 总被引：1，自引：0，他引：1
Recent backscattering measurements made in the Gulf of La Spezia, Italy, using a sonar operating at 140 kHz combined with thorough characterization of seabed interface and volume properties illustrate the importance of seabed volume scattering. Three-dimensional fluctuation statistics of density variability and vertical density gradients, both of which are attributed to the level of bioturbation (e.g., sea shell fragments, burrows, pockets of water) have been quantified using X-Ray computed tomography. Two-dimensional interface roughness spectra have also been determined using a digital stereo photogrammetry system. The combined ground truth has allowed a backscattering model to be fully constrained. Measured backscattering strength versus angle is compared to a model that includes the effects of varying density and sound speed. Data-model comparisons show that scattering from the volume of strongly inhomogeneous sediments can often be a primary contributor to seafloor scattering away from normal incidence. 相似文献
10.
A joint surface roughness/volumetric perturbation scattering theory is utilized to characterize the reverberation from a littoral ocean bottom. The result is a reflected field spectrum that consists of specular and off-specular components. The predicted scattering strength from the off-specular component is shown to be comprised of interface roughness scattering, sediment inhomogeneity volumetric scattering, and interface roughness/sediment inhomogeneity correlation scattering. The sediment inhomogeneity volumetric scattering is shown to contain two contributions that are due to fractional variations in sediment densities and sound velocities. Both contributions are shown to be affected by the interface effect by a round-trip transmission coefficient factor. These two fractional variations are shown to contribute differently to scattering strength but similarly to backscattering strength. Inversely predicted roughness spectra from various sets of backscattering strength data are shown to be consistent with a generally known roughness spectrum. Both inversely predicted roughness and volumetric scattering physical property spectra are found to be self-consistent. However, the use of only ocean bottom backscattering strength data is found to be insufficient to judge whether the roughness or the volumetric scattering dominates. Reverberation characterizations using bistatic scattering strength data and signal spread data are planned for future studies 相似文献
11.
The microwave backscattering from wind-wave surfaces is observed in a windwave tunnel under various conditions of the wind and wind waves, and its statistical features are investigated. The dependence of the backscattered power on the wind speed and the incident angle shows similar features to those predicted by models proposed previously. However, the dependence of the backscattered power on the incident angles also corresponds to the asymmetrical feature of the wind-wave surfaces with respect to the wind direction. The spectral analyses of time series of the backscattered intensity show that the propagating speed of fine structures of the wind-wave surface contributing to the backscattering at large incident angles does not coincide with the phase speed of the freely propagating Braggwaves. Atupwind incidence, the surface structures of wind waves contributing to the backscattering propagates with the dominant waves at their phase speed. This result is inconsistent with the two-scale model in which the Bragg waves are simply superimposed on longer waves, but is consistent with the results of optical observation by Ebuchiet al. (1987). At downwind incidence, the propagating speed is slower than the phase speed of the dominant waves. 相似文献
12.
The sediment backscatter strength measured by multibeam echosounders is a key feature for seafloor mapping either qualitative (image mosaics) or quantitative (extraction of classifying features). An important phenomenon, often underestimated, is the dependence of the backscatter level on the azimuth angle imposed by the survey line directions: strong level differences at varying azimuth can be observed in case of organized roughness of the seabed, usually caused by tide currents over sandy sediments. This paper presents a number of experimental results obtained from shallow-water cruises using a 300-kHz multibeam echosounder and specially dedicated to the study of this azimuthal effect, with a specific configuration of the survey strategy involving a systematic coverage of reference areas following “compass rose” patterns. The results show for some areas a very strong dependence of the backscatter level, up to about 10-dB differences at intermediate oblique angles, although the presence of these ripples cannot be observed directly—neither from the bathymetry data nor from the sonar image, due to the insufficient resolution capability of the sonar. An elementary modeling of backscattering from rippled interfaces explains and comforts these observations. The consequences of this backscatter dependence upon survey azimuth on the current strategies of backscatter data acquisition and exploitation are discussed. 相似文献
13.
This paper describes the simulation of backscattering of high frequency sound from complex objects and sand sea-bottom. Backscattering data from complex objects and seabottom were generated using a Universal High Resolution Imaging Sonar Simulation Toolkit (UHRISST) developed by the authors. Our approach here involves the approximation of objects and the sea-bottom through a series of facets that are small compared to the wavelength. The Target Strength of standard objects like the sphere, cylinder, and cone predicted by our model have been compared with various high frequency approximation formulations and produced a good fit. For the prediction of the backscattering strength from the sea-bottom, we have taken into account most of the small-scale features that represent the sand grain properties, intermediate features that represent seabottom roughness and large features that block propagation. Sea-bottom backscattering predictions made using this model were compared with high frequency scattering strength values measured off Panama City, FL, USA, and produced a moderate fit. Nonparametric statistical analysis was carried out on the bottom backscattering signals from a flat isotropic sea-bottom. The probability distribution function and probability of false alarm function of the bottom backscattering data was measured and found to largely follow the normal distribution 相似文献
14.
Dimitrios Eleftherakis Laurent Berger Naig Le Bouffant Anne Pacault Jean-Marie Augustin Xavier Lurton 《Marine Geophysical Researches》2018,39(1-2):55-73
The calibration of multibeam echosounders for backscatter measurements can be conducted efficiently and accurately using data from surveys over a reference natural area, implying appropriate measurements of the local absolute values of backscatter. Such a shallow area (20-m mean depth) has been defined and qualified in the Bay of Brest (France), and chosen as a reference area for multibeam systems operating at 200 and 300 kHz. The absolute reflectivity over the area was measured using a calibrated single-beam fishery echosounder (Simrad EK60) tilted at incidence angles varying between 0° and 60° with a step of 3°. This reference backscatter level is then compared to the average backscatter values obtained by a multibeam echosounder (here a Kongsberg EM 2040-D) at a close frequency and measured as a function of angle; the difference gives the angular bias applicable to the multibeam system for recorded level calibration. The method is validated by checking the single- and multibeam data obtained on other areas with sediment types different from the reference area. 相似文献
15.
An accurate model of acoustic interaction with sandy sediments is crucial to the application of SONAR in shallow-water environments. Because acoustic scattering from interface roughness plays a major role in the reverberation from and penetration into sandy sediments, it is imperative to be able to accurately measure the roughness of the sediment/water interface. An interface roughness measurement system has been developed in which a laser light sheet is projected onto the ocean floor. A resulting image can then be analyzed to determine the interface roughness. The system has been shown to achieve a height measurement error of less than 0.9 mm over a spatial frequency range of 15 to 60 cycles/m with about 0.5 mm standard deviation. These spatial frequencies correspond to acoustic Bragg frequencies of 11 to 45 kHz for backscattering applications. The error in wavelength was less than 5 mm with a standard deviation of about 1.0 mm. The system is inexpensive, easily deployable and automated in terms of data extraction. This system could greatly aid in determining the local interface profile for in situ acoustic scattering experiments. 相似文献
16.
17.
High-frequency bistatic sediment scattering experiment was conducted in the shallow waters off the east coasts of Korea. Acoustic data were taken as a function of grazing angle (30°, 45°, and 60°), scattered angle (30°, 45°, and 60°), and bistatic (azimuthal) angle (0°, 60°, and 120°). Besides a flat bottom it was artificially raked so as to produce directional ripples. The measured scattering strengths for a flat bottom were compared to model predictions of D.R. Jackson et al. (1986). The surface reverberation component is seen to dominate over the volume scattering part at the frequency of 240 kHz. Compared to the flat bottom case, the scattering strengths for directional ripples showed lower and higher variation depending on the ripple's orientation 相似文献
18.
The EM12 multibeam echosounder can record acoustic backscatter information as well as high resolution bathymetry. The dataset presented, from the axis of the Mid-Atlantic Ridge at 45° N, was the first EM12 survey of a mid-ocean ridge. This paper presents methods for utilising the backscatter information. Data processing enables the production of a mosaic of acoustic backscatter, and visualisation techniques are investigated to provide initial qualitative views of the combined backscatter and bathymetry datasets. The co-registration of the backscatter and bathymetry data enables quantitative analysis of their relationships. Various sites of different geological type have been selected and their angular acoustic backscattering relationships estimated, including the effect on backscatter of incidence angle, its regional variability with bottom type and the influence of bottom slope. Incidence angles and bottom type are shown to affect backscatter to a similar degree, while slopes appear to contribute little. The geometry of hull-mounted systems, such as the EM12, is significantly different from that of conventional sidescan sonars, such as GLORIA, and the backscatter images from the two types differ in various respects. Because of the wide variations in incidence angle that are common with hull-mounted systems, and the importance of incidence angle in determining backscatter strength, it is vital to consider the effect of incidence angle during interpretation. 相似文献
19.
Tests of models for high-frequency seafloor backscatter 总被引：3，自引：0，他引：3
Jackson D.R. Briggs K.B. Williams K.L. Richardson M.D. 《Oceanic Engineering, IEEE Journal of》1996,21(4):458-470
The interaction of high-frequency sound with the seafloor is inherently a stochastic process. Inversion techniques must, therefore employ good stochastic models for bottom acoustic scattering. An assortment of physical models for bottom backscattering strength is tested by comparison with scattering strength data obtained at 40 kHz at three shallow water sites spanning a range of sediment types from fine silt to coarse sand. These acoustic data are accompanied by sediment physical property data obtained by core sample analysis and in situ probes. In addition, stereo photography was used to measure the power spectrum of bottom relief on centimeter scales. These physical data provided the inputs needed to test the backscatter models, which treat scattering from both the rough sediment-water interface and the sediment volume. For the three sites considered here, the perturbation model for scattering from a slightly rough fluid seafloor performs well. Volume scattering is predicted to be weak except at a site having a layer of methane bubbles 相似文献
20.
Cable P.G. Yudichak T.W. Dorfman Y. Knobles D.P. Renhe Zhang Zhaohui Peng Fenghua Li Zhenglin Li 《Oceanic Engineering, IEEE Journal of》2006,31(1):145-155
Determinations of bottom scattering strength in the decade below 1 kHz under downward refracting conditions have been made using acoustic reverberation and transmission data from the 2001 East China Sea Asian Seas International Acoustic Experiment (ASIAEX). The measurements were performed using explosive sources and receiving hydrophones in ship-suspended vertical-line arrays. The focus of this paper has been the dependence of bottom scattering strength on the frequency and characterization of the uncertainties associated with the extraction of scattering strength from reverberation. The derived bottom scattering strength gradually rises with frequency from 100-300 Hz and then more rapidly above 300 Hz. A potential explanation suggests that the frequency variation results from two scattering mechanisms, rough layer scattering at the low end of the band and sediment near-surface volume scattering at the high end. The spatial extrapolation of these results is explored by comparing them with similarly derived scattering strengths using data obtained under the Navy's Harsh Environments Program at a somewhat separated site (56 km) under environmental conditions similar to those during ASIAEX. In the ASIAEX analysis, it has been found that the largest source of uncertainty in the scattering-strength frequency dependence arises from persistence of finite-amplitude effects associated with the source signal. 相似文献