共查询到20条相似文献，搜索用时 31 毫秒
1.
Seismic data often contain traces that are dominated by noise; these traces should be removed (edited) before multichannel filtering or stacking. Noise bursts and spikes should be edited before single channel filtering. Spikes can be edited using a running median filter with a threshold; noise bursts can be edited by comparing the amplitudes of each trace to those of traces that are nearby in offset-common midpoint space. Relative amplitude decay rates of traces are diagnostic of their signal-to-noise (S/N) ratios and can be used to define trace editing criteria. The relative amplitude decay rate is calculated by comparing the time-gated trace amplitudes to a control function that is the median trace amplitude as a function of time, offset, and common midpoint. The editing threshold is set using a data-adaptive procedure that analyses a histogram of the amplitude decay rates. A performance evaluation shows that the algorithm makes slightly fewer incorrect trace editing decisions than human editors. The procedure for threshold setting achieves a good balance between preserving the fold of the data and removing the noisiest traces. Tests using a synthetic seismic line show that the relative amplitude decay rates are diagnostic of the traces’S/N ratios. However, the S/N ratios cannot be accurately usefully estimated at the start of processing, where noisy-trace editing is most needed; this is the fundamental limit to the accuracy of noisy trace editing. When trace equalization is omitted from the processing flow (as in amplitude-versus-offset analysis), precise noisy-trace editing is critical. The S/N ratio of the stack is more sensitive to type 2 errors (failing to reject noisy traces) than it is to type 1 errors (rejecting good traces). However, as the fold of the data decreases, the S/N ratio of the stack becomes increasingly sensitive to type 1 errors. 相似文献
2.
R. E. WHITE 《Geophysical Prospecting》1977,25(1):165-178
Optimum stacking filters based on estimates of trace signal-to-uncorrelated noise ratios are assessed and compared in performance with conventional straight stacking. It is shown that for the trace durations and signal bandwidths normally encountered in seismic reflection data the errors in estimating signal/noise ratios largely counteract the theoretical advantages of the optimum filter. The more specific the filter (e.g. the more frequency components included in its design) the more this is true. Even for a simple weighted stack independent of frequency, the performance is likely to be better than a straight (equal weights) stack only for relatively high signal/noise ratios, when the performance is not critical anyway. 相似文献
3.
Singular value decomposition (SVD) is a useful method for random noise suppression in seismic data processing. A structure-oriented SVD (SOSVD) approach which incorporates structure prediction to the SVD filter is effcient in attenuating noise except distorting seismic events at faults and crossing points. A modified SOSVD approach using a weighted stack, called structure-oriented weighted SVD (SOWSVD), is proposed. In this approach, the SVD filter is used to attenuate noise for prediction traces of a primitive trace which are produced via the plane-wave prediction. A weighting function related to local similarity and distance between each prediction trace and the primitive trace is applied to the denoised prediction traces stacking. Both synthetic and field data examples suggest the SOWSVD performs better than the SOSVD in both suppressing random noise and preserving the information of the discontinuities for seismic data with crossing events and faults.
相似文献4.
水平叠加技术能够有效地压制随机噪声和多次波，但是对于由于相邻道的噪声表现出相关性和一致性而产生的某些相干干扰，常规的叠加技术容易产生假的同相轴，难以取得较高的信噪比.基于小波理论和高阶统计理论本文提出了小波域高阶相关叠加技术(HOCS)，其基本原理是将经动静校正的CMP道集变换到小波域，然后在小波域求取高阶相关系数，进而加权叠加.数值实验和实际资料计算的结果表明，此方法比常规叠加更能够有效地提高信噪比，剔除常规加权叠加无法抑制的某些相关噪声. 相似文献
5.
Local seismic event slopes contain subsurface velocity information and can be used to estimate seismic stacking velocity. In this paper, we propose a novel approach to estimate the stacking velocity automatically from seismic reflection data using similarity‐weighted k‐means clustering, in which the weights are local similarity between each trace in common midpoint gather and a reference trace. Local similarity reflects the local signal‐to‐noise ratio in common midpoint gather. We select the data points with high signal‐to‐noise ratio to be used in the velocity estimation with large weights in mapped traveltime and velocity domain by similarity‐weighted k‐means clustering with thresholding. By using weighted k‐means clustering, we make clustering centroids closer to those data points with large weights, which are more reliable and have higher signal‐to‐noise ratio. The interpolation is used to obtain the whole velocity volume after we have got velocity points calculated by weighted k‐means clustering. Using the proposed method, one obtains a more accurate estimate of the stacking velocity because the similarity‐based weighting in clustering takes into account the signal‐to‐noise ratio and reliability of different data points in mapped traveltime and velocity domain. In order to demonstrate that, we apply the proposed method to synthetic and field data examples, and the resulting images are of higher quality when compared with the ones obtained using existing methods. 相似文献
6.
HENRY J. MEYERHOFF 《Geophysical Prospecting》1966,14(Z2):441-453
The common depth point method of shooting in oil exploration provides a series of seismic traces which yield information about the substrata layers at one location. After normal moveout and static corrections have been applied, the traces are combined by horizontal stacking, or linear multichannel filtering, into a single record in which the primary reflections have been enhanced relative to the multiple reflections and random noise. The criterion used in optimum horizontal stacking is to maximize the signal to noise power ratio, where signal refers to the primary reflection sequence and noise includes the multiple reflections. It is shown when this criterion is equivalent to minimizing the mean square difference between the desired signal (primary reflection sequence) and the weighted horizontally stacked traces. If the seismic traces are combined by multichannel linear filtering, the primary reflection sequence will have undergone some phase and frequency distortion on the resulting record. The signal to noise power ratio then becomes less meaningful a criterion for designing the optimum linear multichannel filter, and the mean square criterion is adopted. In general, however, since more a priori information about the seismic traces is required to design the optimum linear multichannel filter than required for the optimum set of weights of the horizontal stacking process, the former will be an improvement over the latter. It becomes evident that optimum horizontal stacking is a restricted form of linear multichannel filtering. 相似文献
7.
宽频带地震观测数据中有效信号和干扰噪声经常发生混频效应,常规的频率域滤波方法很难将二者分离.地震波信号属于时变非平稳信号,时频分析方法能够同时得到地震波信号随着时间和频率变化的振幅和相位特征,S变换是其中较为高效的时频分析工具之一.本文以S变换为例,提出了基于相位叠加的时频域相位滤波方法.与传统叠加方法相比,相位叠加方法对强振幅不敏感,对波形一致性相当敏感,更加利于有效弱信号信息的检测.时频域相位滤波方法滤除与有效信号不相干的背景噪声,保留了相位一致的有效信号成分,显著提高了信噪比.运用理论合成的远震接收函数数据和实际的宽频带地震观测数据检验结果显示该方法较传统的带通滤波方法相比,即使在信噪较低且混频严重条件下,时频域相位滤波方法的滤波效果依然很明显,有助于识别能量较弱的有效信号. 相似文献
8.
Hakan Karslı 《Geophysical Prospecting》2011,59(1):56-65
Interpreting a post‐stack seismic section is difficult due to the band‐limited nature of the seismic data even post deconvolution. Deconvolution is a process that is universally applied to extend the bandwidth of seismic data. However, deconvolution falls short of this task as low and high frequencies of the deconvolved data are either still missing or contaminated by noise. In this paper we use the autoregressive extrapolation technique to recover these missing frequencies, using the high signal‐to‐noise ratio (S/N) portions of the spectrum of deconvolved data. I introduce here an algorithm to extend the bandwidth of deconvolved data. This is achieved via an autoregressive extrapolation technique, which has been widely used to replace missing or corrupted samples of data in signal processing. This method is performed in the spectral domain. The spectral band to be extrapolated using autoregressive prediction filters is first selected from the part of the spectrum that has a high signal‐to‐noise ratio (S/N) and is then extended. As there can be more than one zone of good S/N in the spectrum, the results of prediction filter design and extrapolation from three different bands are averaged. When the spectrum of deconvolved data is extended in this way, the results show higher vertical resolution to a degree that the final seismic data closely resemble what is considered to be a reflectivity sequence of the layered medium. This helps to obtain acoustic impedance with inversion by stable integration. The results show that autoregressive spectral extrapolation highly increases vertical resolution and improves horizon tracking to determine continuities and faults. This increase in coherence ultimately yields a more interpretable seismic section. 相似文献
9.
Common reflection surface stack using dip decomposition for rugged surface topography 总被引：1，自引：0，他引：1
We present an extension of the Common Reflection Surface （CRS） stack that provides support for an arbitrary top surface topography. CRS stacking can be applied to the original prestack data without the need for any elevation statics. The CRS-stacked zero- offset section can be corrected （redatumed） to a given planar level by kinematic wave field attributes. The seismic processing results indicate that the CRS stacked section for rugged surface topography is better than the conventional stacked section for S/N ratio and better continuity of reflection events. Considering the multiple paths of zero-offset rays, the method deals with reflection information coming from different dips and performs the stack using the method of dip decomposition, which improves the kinematic and dynamic character of CRS stacked sections. 相似文献
10.
Further improvement of temporal resolution of seismic data by autoregressive (AR) spectral extrapolation 总被引：1，自引：0，他引：1
Hakan Karsl&#x; 《Journal of Applied Geophysics》2006,59(4):324-336
Seismic data have still no enough temporal resolution because of band-limited nature of available data even if it is deconvolved. However, lower and higher frequency information belonging to seismic data is missing and it is not directly recovered from seismic data. In this paper, a method originally applied by Honarvar et al. [Honarvar, F., Sheikhzadeh, H., Moles, M., Sinclair, A.N., 2004. Improving the time-resolution and signal–noise ratio of ultrasonic NDE signals. Ultrasonics 41, 755–763.] which is the combination of the most widely used Wiener deconvolution and AR spectral extrapolation in frequency domain is briefly reviewed and is applied to seismic data to improve temporal resolution further. The missing frequency information is optimally recovered by forward and backward extrapolation based on the selection of a high signal–noise ratio (SNR) of signal spectrum deconvolved in signal processing technique. The combination of the two methods is firstly tested on a variety of synthetic examples and then applied to a stacked real trace. The selection of necessary parameters in Wiener filtering and in extrapolation are discussed in detail. It is used an optimum frequency windows between 3 and 10 dB drops by comparing results from these drops, while frequency windows are used as standard between 2.8 and 3.2 dB drops in study of Honarvar et al. [Honarvar, F., Sheikhzadeh, H., Moles, M., Sinclair, A.N., 2004. Improving the time-resolution and signal–noise ratio of ultrasonic NDE signals. Ultrasonics 41, 755–763.]. The results obtained show that the application of the purposed signal processing technique considerably improves temporal resolution of seismic data when compared with the original seismic data. Furthermore, AR based spectral extrapolated data can be almost considered as reflectivity sequence of layered medium. Consequently, the combination of Wiener deconvolution and AR spectral extrapolation can reveal some details of seismic data that cannot be observed in raw signal or which lost during the previous processing. 相似文献
11.
横波速度动校正后的共转换点(CCP)道集内,同时刻的各道横波信号S变换(ST)谱与其叠加道ST谱具有相似关系.因此,可基于这种相似关系设计自适应滤波器来提取多波地震数据中的横波波场.首先对共中心点(CMP)道集应用纵波速度动校正并在各道减去叠加道来去除数据中的纵波波场;然后在CCP道集应用横波速度动校正,将地震道振幅水平调整至叠加道振幅水平并做S变换,以叠加道ST谱为参考对地震道ST谱进行自适应滤波,去除数据中的残余纵波和噪声;最后,将滤波结果的振幅水平恢复至滤波前振幅水平.理论和实际数据试算表明,本文方法可有效提取多波地震数据中的横波波场,为多波多分量横波数据处理提供新思路. 相似文献
12.
In this case study we consider the seismic processing of a challenging land data set from the Arabian Peninsula. It suffers from rough top‐surface topography, a strongly varying weathering layer, and complex near‐surface geology. We aim at establishing a new seismic imaging workflow, well‐suited to these specific problems of land data processing. This workflow is based on the common‐reflection‐surface stack for topography, a generalized high‐density velocity analysis and stacking process. It is applied in a non‐interactive manner and provides an entire set of physically interpretable stacking parameters that include and complement the conventional stacking velocity. The implementation introduced combines two different approaches to topography handling to minimize the computational effort: after initial values of the stacking parameters are determined for a smoothly curved floating datum using conventional elevation statics, the final stack and also the related residual static correction are applied to the original prestack data, considering the true source and receiver elevations without the assumption of nearly vertical rays. Finally, we extrapolate all results to a chosen planar reference level using the stacking parameters. This redatuming procedure removes the influence of the rough measurement surface and provides standardized input for interpretation, tomographic velocity model determination, and post‐stack depth migration. The methodology of the residual static correction employed and the details of its application to this data example are discussed in a separate paper in this issue. In view of the complex near‐surface conditions, the imaging workflow that is conducted, i.e. stack – residual static correction – redatuming – tomographic inversion – prestack and post‐stack depth migration, leads to a significant improvement in resolution, signal‐to‐noise ratio and reflector continuity. 相似文献
13.
Jing Liu Youcai Tang Kai Tao Chunquan Yu Jie Chen Jieyuan Ning Yongshun John Chen Yongge Feng 《地震科学（英文版）》2010,23(6):627-636
We have developed a new stacking technique in ambient noise tomography to obtain high-quality dispersion curves of Rayleigh waves.This technique is used to stack the vertical components of the Estimated Green Functions(EGFs) obtained respectively from cross correlation of the ambient noise data recorded by a remote seismic station and one of the short distance seismic stations of a seismic array.It is based on a phase-matched filter and is implemented by a four-step iterative process:signal compression,stacking,signal extraction and signal decompression.The iterative process ends and gives the dispersion curve of Rayleigh wave when the predicted one and the processing result converge.We have tested the method using the vertical components of synthetic Rayleigh wave records.Results show that this new stacking method is stable and it can improve the quality of dispersion curves.In addition,we have applied this method to real data.We see that the results given by our new technique are obviously better than the ones employing the traditional method which is a three-step process:signal compression,signal extraction and signal decompression.In conclusion,the new method proposed in this paper can improve the signal to noise ratio of EGFs,and can therefore potentially improve the resolution of ambient noise tomography. 相似文献
14.
估算剩余静校正量可看作是以激发点及接收点剩余静校正量为模型参数的、以叠加能量为目标函数的全局最优值的搜索问题．当地震记录的剩余静校正量大而信噪比较低时，应用相关统计法不能有效地拾取静校正量．本文分别采用了ＣＭＰ道集内道间互相关法、图像边缘提取的Ｌａｐｌａｃｉａｎ算法及ＤＦＰ算法，三种不同算法联合迭代反演可求取最佳的模型参数，使目标函数值达到或接近于全局最优．理论试算及实际资料处理效果表明，这种方法能够解决低信噪比及大静校正量造成的周期跳跃等静校正问题． 相似文献
15.
16.
Static shifts from near‐surface inhomogeneities very often represent the key problem in the processing of seismic data from arid regions. In this case study, the deep bottom fill of a wadi strongly degrades the image quality of a 2D seismic data set. The resulting static and dynamic problems are solved by both conventional and common‐reflection‐surface (CRS) processing. A straightforward approach derives conventional refraction statics from picked first breaks and then goes through several iterations of manual velocity picking and residual statics calculation. The surface‐induced static and dynamic inhomogeneities, however, are not completely solved by these conventional methods. In CRS processing, the local adaptation of the CRS stacking parameters results in very detailed dynamic corrections. They resolve the local inhomogeneities that were not detected by manual picking of stacking velocities and largely compensate for the surface‐induced deterioration in the stack. The subsequent CRS residual statics calculations benefit greatly from the large CRS stacking fold which increases the numbers of estimates for single static shifts. This improves the surface‐consistent averaging of static shifts and the convergence of the static solution which removes the remaining static shifts in the 2D seismic data. The large CRS stacking fold also increases the signal‐to‐noise ratio in the final CRS stack. 相似文献
17.
18.
B. URSIN 《Geophysical Prospecting》1978,26(4):722-749
The use of arrays to separate primary reflections from unwanted coherent seismic events is common practice in land seismic surveys. Very long source and receiver arrays have been used recently to reduce the effects of waterbottom multiples on marine seismic data. The source array consists of five uniformly spaced identical subarrays, each with five different airguns, where the distance between the subarrays may vary from 20 m56 m. The volume of each subarray is 10.3 1 (630 cu.in.) which gives a total volume of the array of 51.5 1 (3150 cu.in.) operated at a pressure of 14 MPa (2000 psi). In order to have a flexible receiver system it was decided to implement the extended receiver array in data processing by computing a weighted sum of two to five traces. The hydrophone cable consists of fifty-four channels with a group length of 50 m. Data shot with the superlong airgun array are processed by a combination of standard techniques and special procedures. In particular, the quality of the stack section is improved by using a weighted stack. The stack weights are computed by a program which takes into account the primary-to-multiple ratio. Comparisons with conventional data show significant improvements in data quality obtained by using the superlong airgun array. Examples show that the waterbottom multiples have been strongly attenuated and the deep seismic events have been enhanced. The combined array response function for dipping events is given in an appendix. 相似文献
19.
多年来,胜利探区多波多分量地震采集所得资料的信噪比和分辨率较低,无法取得较好的应用效果.为此,以胜利垦71区块为先导实验区开展了多波采集方法研究.首先,通过单点三分量检波器与常规检波器小面积组合分析了该区转换波发育情况,认为该区转换界面较强,转换波特征明显,转换横波速度约为纵波速度的1/2;然后,通过数字三分量检波器的室内各种组合研究,进行了超线元叠加,由此可以有效地改善资料的信噪比,并对分辨率基本没有影响;最后,利用三分量检波器扩展排列进行转换波最佳偏移距的设计,通过垂直排列追踪放炮进行最佳非纵距设计,从而得出该区多波采集的最佳观测系统参数.通过上述合理的设计和多项试验研究,在垦71地区多波采集中,数字检波器Z分量剖面的频率优势非常明显,分辨率明显高于常规检波器的纵波剖面,对于搞清小断层及微幅度构造具有重要的意义;同时,转换横波能量强、信噪比和分辨率高,使多波采集取得了较好的效果. 相似文献
20.
Jürgen Mann Rainer Jger Thilo Müller German Hcht Peter Hubral 《Journal of Applied Geophysics》1999,42(3-4)
The simulation of a zero-offset (ZO) stack section from multi-coverage reflection data is a standard imaging method in seismic processing. It significantly reduces the amount of data and increases the signal-to-noise ratio due to constructive interference of correlated events. Conventional imaging methods, e.g., normal moveout (NMO)/dip moveout (DMO)/stack or pre-stack migration, require a sufficiently accurate macro-velocity model to yield appropriate results, whereas the recently introduced common-reflection-surface stack does not depend on a macro-velocity model. For two-dimensional seismic acquisition, its stacking operator depends on three wavefield attributes and approximates the kinematic multi-coverage reflection response of curved interfaces in laterally inhomogeneous media. The common-reflection-surface stack moveout formula defines a stacking surface for each particular sample in the ZO section to be simulated. The stacking surfaces that fit best to actual events in the multi-coverage data set are determined by means of coherency analysis. In this way, we obtain a coherency section and a section of each of the three wavefield attributes defining the stacking operator. These wavefield attributes characterize the curved interfaces and, thus, can be used for a subsequent inversion. In this paper, we focus on an application to a real land data set acquired over a salt dome. We propose three separate one-parametric search and coherency analyses to determine initial common-reflection-surface stack parameters. Optionally, a subsequent optimization algorithm can be performed to refine these initial parameters. The simulated ZO section obtained by the common-reflection-surface stack is compared to the result of a conventional NMO/DMO/stack processing sequence. We observe an increased signal-to-noise ratio and an improved continuity along the events for our proposed method — without loss of lateral resolution. 相似文献