共查询到20条相似文献，搜索用时 78 毫秒
1.
土壤中重金属元素电感耦合等离子体质谱定量分析方法的研究 总被引：7，自引：7，他引：0
分别采用HNO3-HF、HNO3-HF-HCl和HNO3-HF-H2O2三种消解体系,通过微波和PTFE密封罐电热板对土壤标准物质进行前处理,采用电感耦合等离子体质谱(ICP-MS)对样品中的重金属元素Cr、Ni、Cu、Zn、As、Cd和Pb进行定量分析。探讨了前处理试剂(主要为HNO3、HCl和HF)以及土壤基体效应对Cr、Ni、Cu、Zn、As、Cd和Pb定量分析的影响。研究结果表明,前处理试剂对Cr、Ni、Cu、Zn、As、Cd和Pb的定量分析具有不同程度的影响;对于土壤基体,在三种消解体系下均可观察到基体抑制效应;采用PTFE密封罐电热板消解方法前处理,待测元素及相同元素不同同位素的方法空白和检出限均较低,效果整体优于微波消解法。特别是HNO3-HF-HCl消解体系,通过选用52Cr、60Ni、65Cu、66Zn、75As和206Pb等同位素,重金属元素Cr、Ni、Cu、Zn、As、Cd和Pb的测定值均能保证在标准值的允许误差范围内,可以满足大批量土壤样品中重金属元素同时定量分析的需要,为高效准确地开展土壤的风险评估以及为土壤的修复治理提供科学依据。 相似文献
2.
《城市地质》2020,(2)
通过测定某铁尾矿库周边土壤中4种重金属元素(Cu、Cr、Pb、Cd)的含量及其形态特征,采用地累积指数法和次生相与原生相比值法(RSP法),探讨了研究区土壤重金属的污染程度。研究结果表明:土壤中重金属Cr、Cu、Cd的平均含量超过北京市土壤背景值,呈现一定的累积效应,重金属元素含量变化趋势为CrCuPbCd。除Cd元素外,其它重金属形态以残渣态为主,占比均为50%以上,各样品重金属酸可溶态(F1)的含量占比大小顺序为CdPbCuCr。评价结果显示75%样品中的Cr、58%的Cu和33%的Cd达到了轻度—中度污染;8%样品中的Cr和17%的Cu达到了中等污染;17%样品中的Cr达到了中等—强污染。区域内各个采样点中Cd元素污染风险较大,除Pb有一个点达到轻度污染风险外,其它Cr、Cu元素基本处于无风险的状态。研究区重金属元素污染风险大小的顺序为CdPbCuCr。 相似文献
3.
地球化学基线是区分地球化学背景和异常的重要参数.在采集和测试自贡市龙潭镇内168个表层土壤样品的基础上,采用了地质统计学方法建立了研究区内重金属元素As、Cd、Cr、Pb、Hg、Cu、Ni、Zn的地球化学基线.在此基础上,应用地质累积指数方法评价了表层土壤重金属的污染状况.结果表明:区内各重金属元素基线值为As(3.86 μg/g)、Cd(0.183μg/g)、Cr(66.41 μg/g)、Pb(28.19 μg/g)、Hg(0.037 μg/g)、Cu( 23.1 μg/g)、Ni(24.5 μg/g)、Zn(62μg/g);研究区内Cd和Hg的污染较突出,各重金属元素的地质累积指数排序为:Cd＞H g＞Zn＞Cu＞As＞Cr＞Ni＞Pb. 相似文献
4.
无高氯酸常压酸溶-ICP-MS法同时测定土壤中的As、Cd、Pb、Cr、Zn、Cu、Ni 总被引：1，自引：0，他引：1
采用无高氯酸常压酸溶分解土壤样品,利用等离子体质谱法可以1次溶矿测定As、Cd、Pb、Cr、Zn、Cu、Ni 7个重金属元素,具有较高的分析效率、较好的分析质量、较低的分析成本。实验表明,试样溶液中氯的含量对分析元素信号有较大影响。采用硝酸-氢氟酸-硫酸-过氧化氢分解样品以避免引入氯离子,从而能有效避免Cr、As元素在样品分解过程中的损失和氯离子产生的质谱干扰。Cd的测定需采用干扰校正公式扣除Sn的干扰。对于As元素,若试样溶液中不含或仅含微量的氯离子,采用标准模式测定即可得到理想的分析结果,否则必须采用CCT模式进行测定。除As以外的其他元素不论在标准模式或CCT模式下均能得到理想的分析结果。 相似文献
5.
6.
基于形态学分析铅锌矿不同功能区土壤重金属元素的分布特征及污染评价 总被引：1，自引：1，他引：0
为掌握尤溪铅锌矿区土壤重金属元素分布特征和污染现状,通过采集尤溪铅锌矿不同功能区0~20cm表层土壤样品,测定土壤中Pb、Zn、Cd、Cu、Cr 5种重金属元素的总量及其化学形态,分析不同功能区土壤重金属污染及分布特征,同时采用次生相与原生相比值法(RSP)进行污染评价。结果表明,尤溪铅锌矿不同功能区土壤中Pb、Zn、Cd含量均超过国家土壤环境质量三级标准,废弃冶炼区土壤Cd、Cu、Pb、Zn含量均最高,分别为标准值的14.78、1.13、3.73、1.34倍,采矿区Cr含量最高,但未超过标准限值。重金属形态结果表明,相比其他元素,Cd弱酸提取态所占比例最高,Cu可交换态比例最高,Pb、Zn、Cr以残渣态为主。RSP法评价表明,不同重金属的污染程度表现为:Cu(1.15)Cd(0.80)Pb(0.59)Zn(0.57)Cr(0.54);不同功能区土壤重金属污染表现为:尾矿库区冶炼区废弃冶炼区采矿区。SPEF法评价表明,尤溪铅锌矿区受人为污染明显,采矿区和尾矿库区Zn污染最为严重,冶炼区和废弃冶炼区Pb污染最为严重,功能区污染顺序为:尾矿库区冶炼区废弃冶炼区采矿区。 相似文献
7.
地球关键带和土壤重金属污染是当今研究的前沿与热点,岩-土体系是地球关键带的重要组成部分。目前海南岛针对不同成壤母质岩-土体系的详细研究较少,并且重金属亟需基于新标准进行评价。为了查清岩-土体系中重金属元素迁移特征及污染状况,本文以海南岛琼中3个土壤垂向剖面及7115件表层土壤样品为研究对象,采用电感耦合等离子体质谱/发射光谱法(ICP-MS/OES)和原子荧光光谱法(AFS)等分析方法,测定岩石和土壤中Cu、Pb、Zn、Cr、Ni、Cd、As和Hg共8种重金属元素含量,利用土壤环境质量农用地土壤污染风险管控标准、内梅罗指数法和潜在生态危害指数法定量评价了表层土壤样品重金属污染状况及生态风险。结果表明,(1)海南岛琼中二长花岗岩岩-土体系中,不同重金属元素表现出明显的分异特征,Cu、Pb、Zn、Cr、Ni、Cd元素以亏损为主,As元素以富集为主,Hg元素则表现出不同的富集或亏损特征,As、Hg元素尤其富集在表层。(2)琼中绝大多数表层土壤中重金属元素含量低于土壤环境质量农用地土壤污染风险筛选值,土壤污染风险低。(3)以琼中和海南岛背景值为评价标准时,应关注Cr、Ni和As污染以及Hg、A... 相似文献
8.
为解决高基质土壤样品中痕量重金属元素检测前处理操作繁琐、样品易二次污染或损失等问题,本文建立了采用固体直接进样-电热蒸发-车载电感耦合等离子体质谱定量分析环境现场土壤样品中Cr、Cu、Zn、As、Cd、Hg和Pb元素的分析方法。该方法采用高温电热蒸发石墨炉作为原子化器,样品称量后经梯度升温选择性蒸发,再结合双通道伴热传输石英管、两路氩气在线稀释、ICP-MS瞬时扫描、基体匹配外部校正等策略,有效解决了土壤直接进样过程中传输效率低、基体效应大的问题。在优化的仪器条件下,按照实验方法称取20mg土壤标准物质GBW07401、GBW07406、GBW07407、GBW07430和GBW07456建立外部校正曲线,样品中7种元素的标准曲线线性相关系数≥0.999;并按照实验方法测定了杭州市滨江区两处田间土壤样品中Cr、Cu、Zn、As、Cd、Hg和Pb,相对标准偏差(RSD)7%,相对误差5%,检出限为1.2～32.0ng/g,回收率为91.0%～113.0%。该方法是一种有实用价值的现场样品分析技术,适合现场中大批量土壤样品的分析监测。 相似文献
9.
土壤重金属含量是影响黄芩产量和质量的重要因素。选取承德市中部金沟屯和五道岭两处黄芩种植示范区为研究区，采集表层土壤样品355件，黄芩样品30件，重金属形态样品15件。在分析土壤Mn、Zn、Cu、Cr、Cd、As、Pb、Ni、Hg、V、Co、Sb和土壤有机质含量（SOM）及pH值，黄芩Zn、Cu、Cr、Co、Cd、Pb、Ni、Hg和As含量基础上，采用描述性统计、地累积指数、主成分和RDA分析、重金属生物富集系数、生物活性系数和迁移系数等方法论述了土壤-黄芩系统重金属生物有效性及迁移累积特征。结果表明:金沟屯和五道岭区土壤各重金属累积程度总体属无-中度累积水平。五道岭Cu和Hg累积程度高于金沟屯区，其它元素累积程度低于金沟屯区。五道岭区表层土壤Cr、Cu和Cd含量超标率分别为2.82%、1.69%和1.13%；金沟屯区土壤Cd、Cr和Ni，五道岭区土壤Zn和Hg含量超标率均为0.56%。五道岭区黄芩Cu元素含量高于金沟屯区，Co和Cu元素生物富集强度高于金沟屯区，其它元素含量和生物富集强度则均低于金沟屯区。土壤Cd和Hg元素生物活性系数相对最高，Ni、Zn和Pb元素次之，Cu、Cr和As生物活性系数相对较低。金沟屯区根系土具有较低的pH值和较高的SOM含量，区内黄芩根部As、Cd、Cr、Ni、Zn和Pb元素BCF平均值高于五道岭区，Cu元素富集强度低于五道岭区。土壤重金属生物有效性和黄芩重金属生物富集强度受土壤pH和SOM含量影响，其中Cd和Cu元素受SOM含量影响最为明显。 相似文献
10.
电解二氧化锰废渣中的重金属元素在雨水淋滤下,通过地表径流对下游水生态系统及农业生态系统造成不同程度的环境污染和安全隐患,因此,准确测定电解二氧化锰废渣浸出液中的重金属元素含量具有重要的现实意义。电解二氧化锰废渣浸出液中的重金属元素含量通常很低,采用原子吸收光谱法、电感耦合等离子体发射光谱法测定,检出限通常难以满足测定要求。采用电感耦合等离子体质谱法(ICP-MS)测定,消除复杂质谱干扰面临挑战。本文采用电感耦合等离子体串联质谱(ICP-MS/MS)测定电解二氧化锰废渣浸出液中的重金属元素含量。电解二氧化锰废渣中6种重金属元素Cr、Ni、As、Cd、Hg、Pb经硫酸和硝酸混合酸浸出后直接采用ICP-MS/MS进行测定,利用串联质谱的O_2反应模式消除分析过程中Cr、Ni、As、Cd受到的质谱干扰,通过考察不同分析模式下~(52)Cr、~(60)Ni、~(75)As、~(111)Cd的背景等效浓度(BEC),评价质谱干扰对分析结果的影响。结果表明:在MS/MS模式下选择O_2为反应气,采用质量转移法和原位质量法可以消除~(52)Cr、~(60)Ni、~(75)As、~(111)Cd的所有质谱干扰。Cr、Ni、As、Cd、Hg、Pb检出限分别为3.06、9.31、3.50、2.72、2.03、1.89ng/L,加标回收率在95.6%～106.2%之间,相对标准偏差(RSD)≤3.9%。所建立的方法已应用于电解二氧化锰废渣浸出液中重金属元素的测定。 相似文献
11.
E. M. Prasolov S. A. Sergeev B. V. Belyatsky E. S. Bogomolov K. A. Gruzdov I. N. Kapitonov R. Sh. Krymsky V. O. Khalenev 《Geochemistry International》2018,56(1):46-64
This paper reports the first results of a study of 11 isotope systems (3He/4He, 40Ar/36Ar, 34S/32S, 65Cu/63Cu, 62Ni/60Ni, 87Sr/86Sr, 143Nd/144Nd, 206–208Pb/204Pb, Hf–Nd, U–Pb, and Re–Os) in the rocks and ores of the Cu–Ni–PGE deposits of the Norilsk ore district. Almost all the results were obtained at the Center of Isotopic Research of the Karpinskii All-Russia Research Institute of Geology. The use of a number of independent genetic isotopic signatures and comprehensive isotopic knowledge provided a methodic basis for the interpretation of approximately 5000 isotopic analyses of various elements. The presence of materials from two sources, crust and mantle, was detected in the composition of the rocks and ores. The contribution of the crustal source is especially significant in the paleofluids (gas–liquid microinclusions) of the ore-forming medium. Crustal solutions were probably a transport medium during ore formation. Air argon is dominant in the ores, which indicates a connection between the paleofluids and the atmosphere. This suggests intense groundwater circulation during the crystallization of ore minerals. The age of the rocks and ores of the Norilsk deposits was determined. The stage of orebody formation is restricted to a narrow age interval of 250 ± 10 Ma. An isotopic criterion was proposed for the ore-bearing potential of mafic intrusions in the Norilsk–Taimyr region. It includes several interrelated isotopic ratios of various elements: He, Ar, S, and others. 相似文献
12.
奥地利安东帕有限公司 《岩矿测试》2009,28(3):306-306
最新的流行病学研究表明,空气中较高浓度的悬浮细颗粒可能对人类的健康有不利的影响。根据该项研究显示,由于心脏病、慢性呼吸问题和肺功能指标恶化而导致死亡率的升高与细尘粒子有关。这些研究结果已经促使欧盟于1999年4月出台了限制空气中二氧化硫、二氧化氮、氧化氮、铅和颗粒物含量的法案(1999/30/EC),对各项指标包括对可吸入PM10颗粒的浓度提出了新的限制性指标。PM10颗粒是指可以通过预分级器分离采集的气体动力学直径小于10μm的细颗粒。目前研究的兴趣重点逐步偏向PM2.5这些更细微颗粒物,PM2.5这种颗粒物对健康有明显的不利影响。在欧盟指令2008/50/EC中,对PM10和PM2.5都提 相似文献
13.
S. Viswanathan K. Surya Prakash Rao B. Mahabaleswar 《Journal of the Geological Society of India》2013,82(6):621-627
Komatiites are mantle-derived ultramafic volcanic rocks. Komatiites have been discovered in several States of India, notably in Karnataka. Studies on the distribution of trace-elements in the komatiites of India are very few. This paper proposes a simple, accurate, precise, rapid, and non-destructive wavelength-dispersive x-ray fluorescence (WDXRF) spectrometric technique for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in komatiites, and discusses the accuracy, precision, limits of detection, x-ray spectral-line interferences, inter-element effects, speed, advantages, and limitations of the technique. The accuracy of the technique is excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Zr, Nb, Ba, Pb, and Th and very good (within 4%) for Y. The precision is also excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th. The limits of detection are: 1 ppm for Sc and V; 2 ppm for Cr, Co, and Ni; 3 ppm for Cu, Zn, Rb, and Sr; 4 ppm for Y and Zr; 6 ppm for Nb; 10 ppm for Ba; 13 ppm for Pb; and 14 ppm for Th. The time taken for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in a batch of 24 samples of komatiites, for a replication of four analyses per sample, by one operator, using a manual WDXRF spectrometer, is only 60 hours. 相似文献
14.
Most sulfide-rich magmatic Ni-Cu-(PGE) deposits form in dynamic magmatic systems by partial melting S-bearing wall rocks with variable degrees of assimilation of miscible silicate and volatile components, and generation of barren to weakly-mineralized immiscible Fe sulfide xenomelts into which Ni-Cu-Co-PGE partition from the magma. Some exceptionally-thick magmatic Cr deposits may form by partial melting oxide-bearing wall rocks with variable degrees of assimilation of the miscible silicate and volatile components, and generation of barren Fe ± Ti oxide xenocrysts into which Cr-Mg-V ± Ti partition from the magma. The products of these processes are variably preserved as skarns, residues, xenoliths, xenocrysts, xenomelts, and xenovolatiles, which play important to critical roles in ore genesis, transport, localization, and/or modification. Incorporation of barren xenoliths/autoliths may induce small amounts of sulfide/chromite to segregate, but incorporation of sulfide xenomelts or oxide xenocrysts with dynamic upgrading of metal tenors (PGE > Cu > Ni > Co and Cr > V > Ti, respectively) is required to make significant ore deposits. Silicate xenomelts are only rarely preserved, but will be variably depleted in chalcophile and ferrous metals. Less dense felsic xenoliths may aid upward sulfide transport by increasing the effective viscosity and decreasing the bulk density of the magma. Denser mafic or metamorphosed xenoliths may also increase the effective viscosity of the magma, but may aid downward sulfide transport by increasing the bulk density of the magma. Sulfide wets olivine, so olivine xenocrysts may act as filter beds to collect advected finely dispersed sulfide droplets, but other silicates and xenoliths may not be wetted by sulfides. Xenovolatiles may retard settling of – or in some cases float – dense sulfide droplets. Reactions of sulfide melts with felsic country rocks may generate Fe-rich skarns that may allow sulfide melts to fractionate to more extreme Cu-Ni-rich compositions. Xenoliths, xenocrysts, xenomelts, and xenovolatiles are more likely to be preserved in cooler basaltic magmas than in hotter komatiitic magmas, and are more likely to be preserved in less dynamic (less turbulent) systems/domain/phases than in more dynamic (more turbulent) systems/domains/phases. Massive to semi-massive Ni-Cu-PGE and Cr mineralization and xenoliths are often localized within footwall embayments, dilations/jogs in dikes, throats of magma conduits, and the horizontal segments of dike-chonolith and dike-sill complexes, which represent fluid dynamic traps for both ascending and descending sulfides/oxides. If skarns, residues, xenoliths, xenocrysts, xenomelts, and/or xenovolatiles are present, they provide important constraints on ore genesis and they are valuable exploration indicators, but they must be included in elemental and isotopic mass balance calculations. 相似文献
15.
《Applied Geochemistry》2001,16(2):137-159
Five hundred and ninety-eight samples of terrestrial moss (Hylocomium splendens and Pleurozium schreberi) collected from a 188,000 km2 area of the central Barents region (NE Norway, N Finland, NW Russia) were analysed by ICP-AES and ICP-MS. Analytical results for Al, B, Ba, Ca, K, La, Mg, Mn, Na, P, Rb, Si, Sr, Th, U and Y concentrations are reported here. Graphical methods of data analysis, such as geochemical maps, cumulative frequency diagrams, boxplots and scatterplots, are used to interpret the origin of the patterns for these elements. None of the elements reported here are emitted in significant amounts from the smelting industry on the Kola Peninsula. Despite the conventional view that moss chemistry reflects atmospheric element input, the nature of the underlying mineral substrate (regolith or bedrock) is found to have a considerable influence on moss composition for several elements. This influence of the chemistry of the mineral substrate can take place in a variety of ways. (1) It can be completely natural, reflecting the ability of higher plants to take up elements from deep soil horizons and shed them with litterfall onto the surface. (2) It can result from naturally increased soil dust input where vegetation is scarce due to harsh climatic conditions for instance. Alternatively, substrate influence can be enhanced by human activity, such as open-cast mining, creation of ‘technogenic deserts’, or handling, transport and storage of ore and ore products, all of which magnify the natural elemental flux from bedrock to ground vegetation. Seaspray is another natural process affecting moss composition in the area (Mg, Na), and this is most visible in the Norwegian part of the study area. Presence or absence of some plant species, e.g., lichens, seems to influence moss chemistry. This is shown by the low concentrations of B or K in moss on the Finnish and Norwegian side of the (fenced) border with Russia, contrasting with high concentrations on the other side (intensive reindeer husbandry west of the border has selectively depleted the lichen population). 相似文献
16.
Mercury,arsenic, antimony,and selenium contents of sediment from the Kuskokwim River,Bethel, Alaska,USA 总被引：1，自引：0，他引：1
The Kuskokwim River at Bethel, Alaska, drains a major mercury-antimony metallogenic province in its upper reaches and tributaries. Bethel (population 4000) is situated on the Kuskokwim floodplain and also draws its water supply from wells located in river-deposited sediment. A boring through overbank and floodplain sediment has provided material to establish a baseline datum for sediment-hosted heavy metals. Mercury (total), arsenic, antimony, and selenium contents were determined; aluminum was also determined and used as normalizing factor. The contents of the heavy metals were relatively constant with depth and do not reflect any potential enrichment from upstream contaminant sources. 相似文献
17.
18.
19.
《Chemical Geology》2007,236(1-2):13-26
We examined the coprecipitation behavior of Ti, Mo, Sn and Sb in Ca–Al–Mg fluorides under two different fluoride forming conditions: at < 70 °C in an ultrasonic bath (denoted as the ultrasonic method) and at 245 °C using a Teflon bomb (denoted as the bomb method). In the ultrasonic method, small amounts of Ti, Mo and Sn coprecipitation were observed with 100% Ca and 100% Mg fluorides. No coprecipitation of Ti, Mo, Sn and Sb in Ca–Al–Mg fluorides occurred when the sample was decomposed by the bomb method except for 100% Ca fluoride. Based on our coprecipitation observations, we have developed a simultaneous determination method for B, Ti, Zr, Nb, Mo, Sn, Sb, Hf and Ta by Q-pole type ICP-MS (ICP-QMS) and sector field type ICP-MS (ICP-SFMS). 9–50 mg of samples with Zr–Mo–Sn–Sb–Hf spikes were decomposed by HF using the bomb method and the ultrasonic method with B spike. The sample was then evaporated and re-dissolved into 0.5 mol l− 1 HF, followed by the removal of fluorides by centrifuging. B, Zr, Mo, Sn, Sb and Hf were measured by ID method. Nb and Ta were measured by the ID-internal standardization method, based on Nb/Mo and Ta/Mo ratios using ICP-QMS, for which pseudo-FI was developed and applied. When 100% recovery yields of Zr and Hf are expected, Nb/Zr and Ta/Hf ratios may also be used. Ti was determined by the ID-internal standardization method, based on the Ti/Nb ratio from ICP-SFMS. Only 0.053 ml sample solution was required for measurement of all 9 elements. Dilution factors of ≤ 340 were aspirated without matrix effects. To demonstrate the applicability of our method, 4 carbonaceous chondrites (Ivuna, Orgueil, Cold Bokkeveld and Allende) as well as GSJ and USGS silicate reference materials of basalts, andesites and peridotites were analyzed. Our analytical results are consistent with previous studies, and the mean reproducibility of each element is 1.0–4.6% for basalts and andesites, and 6.7–11% for peridotites except for TiO2. 相似文献
20.
The Samchampi-Samteran alkaline igneous complex (SAC) is a near circular, plug-like body approximately 12 km2 area and is emplaced into the Precambrian gneissic terrain of the Karbi Anglong district of Assam. The host rocks, which
are exposed in immediate vicinity of the intrusion, comprise granite gneiss, migmatite, granodiorite, amphibolite, pegmatite
and quartz veins.
The SAC is composed of a wide variety of lithologies identified as syenitic fenite, magnetite ± perovskite ± apatite rock,
alkali pyroxenite, ijolite-melteigite, carbonatite, nepheline syenite with leucocratic and mesocratic variants, phonolite,
volcanic tuff, phosphatic rock and chert breccia.
The magnetite ± perovskite ± apatite rock was generated as a cumulus phase owing to the partitioning of Ti, Fe at a shallow
level magma chamber (not evolved DI = O1). The highly alkaline hydrous fluid activity indicated by the presence of strongly
alkalic minerals in carbonatites and associated alkaline rocks suggests that the composition of original melt was more alkalic
than those now found and represent a silica undersaturated ultramafic rock of carbonated olivine-poor nephelinite which splits
with falling temperature into two immiscible fractions—one ultimately crystallises as alkali pyroxenite/ijolite and the other
as carbonatite. The spatial distribution of varied lithotypes of SAC and their genetic relationships suggests that the silicate
and carbonate melts, produced through liquid immiscibility, during ascent generated into an array of lithotypes and also reaction
with the country rocks by alkali emanations produced fenitic aureoles (nephelinisation process). Isotopic studies (δ18O and δ13C) on carbonatites of Samchampi have indicated that the δ13C of the source magma is related to contamination from recycled carbon. 相似文献