共查询到20条相似文献，搜索用时 46 毫秒
1.
<正> 磷矿的重介质选矿试验研究,为我国磷块岩的选矿开辟了一条新的工艺路线。探讨其适用条件等有关问题及其工业化问题,具有实际意义。适合重介质分选的磷矿工艺矿物学特征(1)磷酸盐矿物、碳酸盐矿物及硅铝酸盐矿物、氧化类矿物分别聚集成为磷块岩、白云岩及页岩条带,相间分布。(2)由于磷矿重介质分选比重较高,为保证良好的分选效果,磷矿粒度下限在1～2mm 较好,上限一般为6～15mm。这就要求磷块岩条带宽度大多数在1～2mm 以上。(3)磷块岩条带和脉石条带间力 相似文献
2.
3.
4.
周正 《矿物岩石地球化学通报》1984,(2)
1960年10月,涂光炽教授提出要建立地质与选矿相结合的边缘学科。23年来,单矿物分选从无到有,初具规模,现已形成独立的体系。1981年在广州召开了全国单矿物分选学术会议,1983年8月又在肇庆举行了全国重砂矿物会议,成立了专业委员会,把重砂矿物及单矿物分选工作正式纳入学科范畴。单矿物分选作为一门边缘学科正在得到迅 相似文献
5.
6.
本文报告了用化学物相分析方法测定菱铁矿单矿物的化学组成。可用富菱铁矿矿石直接测得菱铁矿单矿物的化学组成,从而解决了难以挑选得到较纯的菱铁矿单矿物的困难。根据碳酸盐矿物中铁、镁、锰和钙等元素形成类质同象置换的几项主要参数,提出了菱铁矿应具有(Fe,Mg,Nn)CO_3的组成。对国内21个菱铁矿矿床产出的菱铁矿石进行研究,其中有三个应定名为锰菱铁矿,五个应定名为镁菱铁矿。方法对菱铁矿矿床的地质研究和菱铁矿石选矿试验中精矿品位的估算具有实用意义。 相似文献
7.
采用XRF、XRD、AMICS、EPMA等多种测试手段,对贵州某地锰矿矿石进行了系统的工艺矿物学研究,包括化学成分分析、矿物组成及含量分析、主要元素的赋存状态研究、主要矿物的嵌布特征和嵌布粒度研究。矿物含量研究在XRD和AMICS半定量分析基础上,通过使用XRF和EPMA校正数据,提高数据的准确性。研究表明,该矿石为低品位中高铁高磷酸性锰矿石,矿石中有用矿物为钙菱锰矿,主要脉石矿物为锰白云石、锰菱铁矿、伊利石、石英、钠长石、黄铁矿及磷灰石。代表性样品w(Mn O)为18.74%,其主要赋存于钙菱锰矿中。钙菱锰矿的百分含量为38.71%,95.00%的Mn赋存其中。钙菱锰矿嵌布粒度主要集中在37.50～178.38μm区间,而脉石矿物的嵌布粒度主要集中在0.83～37.50μm区间。 相似文献
8.
9.
采用高盐分、高硬度的海水、苦卤水、高循环选矿回水等高含盐水进行浮选将是未来沿海缺水地区选矿行业发展的必经之路,这些高含盐水中高浓度离子对矿物浮选的影响机理一直是选矿研究的热点之一。本文回顾了国内外学者在海水、苦卤水、高循环选矿回水等对矿物浮选影响及其作用机制方面的研究工作,系统分析了高含盐水中离子对浮选气泡、矿物表面性质以及浮选药剂的影响。高含盐水给矿物浮选带来众多积极影响,包括降低气泡表面张力产生数量更多、稳定性更强的气泡,提高矿化泡沫形成几率;压缩矿物表面双电层,减弱矿物颗粒之间的静电力,减小细粒脉石矿物浮选过程中的夹带等。同时,高含盐水中的离子也会消耗浮选药剂,且强碱性条件下高价碱金属离子在矿物表面形成亲水沉淀降低矿物可浮性,影响选矿指标。针对高含盐水的负面影响,认为主要应对措施包括研发消除高钙镁离子影响和高耐受性药剂以及淡化、软化高盐水,这也是未来使用高含盐水浮选必然关注的重点。 相似文献
10.
文章使用开放流动反应装置研究了中低温热液矿床中常见脉石矿物碳酸盐(白云石、菱锰矿)在25℃～250℃水中化学动力学溶解反应速率。在25℃条件下,碳酸盐矿物的溶解速率r(Ca)>r(Mn)>r(Mg)。碳酸盐矿物在水中200℃时具有最大溶解速率。随着温度的继续升高,Mg、Mn碳酸盐的溶解反应速率会下降,容易形成白云石和锰碳酸盐。实验研究结果有助于理解中低温环境下,金属矿石的主要伴生碳酸盐矿物与水反应的化学动力学限制,试图说明中低温矿石伴随白云石和锰碳酸盐的沉淀机理。 相似文献
11.
S. Viswanathan K. Surya Prakash Rao B. Mahabaleswar 《Journal of the Geological Society of India》2013,82(6):621-627
Komatiites are mantle-derived ultramafic volcanic rocks. Komatiites have been discovered in several States of India, notably in Karnataka. Studies on the distribution of trace-elements in the komatiites of India are very few. This paper proposes a simple, accurate, precise, rapid, and non-destructive wavelength-dispersive x-ray fluorescence (WDXRF) spectrometric technique for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in komatiites, and discusses the accuracy, precision, limits of detection, x-ray spectral-line interferences, inter-element effects, speed, advantages, and limitations of the technique. The accuracy of the technique is excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Zr, Nb, Ba, Pb, and Th and very good (within 4%) for Y. The precision is also excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th. The limits of detection are: 1 ppm for Sc and V; 2 ppm for Cr, Co, and Ni; 3 ppm for Cu, Zn, Rb, and Sr; 4 ppm for Y and Zr; 6 ppm for Nb; 10 ppm for Ba; 13 ppm for Pb; and 14 ppm for Th. The time taken for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in a batch of 24 samples of komatiites, for a replication of four analyses per sample, by one operator, using a manual WDXRF spectrometer, is only 60 hours. 相似文献
12.
奥地利安东帕有限公司 《岩矿测试》2009,28(3):306-306
最新的流行病学研究表明,空气中较高浓度的悬浮细颗粒可能对人类的健康有不利的影响。根据该项研究显示,由于心脏病、慢性呼吸问题和肺功能指标恶化而导致死亡率的升高与细尘粒子有关。这些研究结果已经促使欧盟于1999年4月出台了限制空气中二氧化硫、二氧化氮、氧化氮、铅和颗粒物含量的法案(1999/30/EC),对各项指标包括对可吸入PM10颗粒的浓度提出了新的限制性指标。PM10颗粒是指可以通过预分级器分离采集的气体动力学直径小于10μm的细颗粒。目前研究的兴趣重点逐步偏向PM2.5这些更细微颗粒物,PM2.5这种颗粒物对健康有明显的不利影响。在欧盟指令2008/50/EC中,对PM10和PM2.5都提 相似文献
13.
E. M. Prasolov S. A. Sergeev B. V. Belyatsky E. S. Bogomolov K. A. Gruzdov I. N. Kapitonov R. Sh. Krymsky V. O. Khalenev 《Geochemistry International》2018,56(1):46-64
This paper reports the first results of a study of 11 isotope systems (3He/4He, 40Ar/36Ar, 34S/32S, 65Cu/63Cu, 62Ni/60Ni, 87Sr/86Sr, 143Nd/144Nd, 206–208Pb/204Pb, Hf–Nd, U–Pb, and Re–Os) in the rocks and ores of the Cu–Ni–PGE deposits of the Norilsk ore district. Almost all the results were obtained at the Center of Isotopic Research of the Karpinskii All-Russia Research Institute of Geology. The use of a number of independent genetic isotopic signatures and comprehensive isotopic knowledge provided a methodic basis for the interpretation of approximately 5000 isotopic analyses of various elements. The presence of materials from two sources, crust and mantle, was detected in the composition of the rocks and ores. The contribution of the crustal source is especially significant in the paleofluids (gas–liquid microinclusions) of the ore-forming medium. Crustal solutions were probably a transport medium during ore formation. Air argon is dominant in the ores, which indicates a connection between the paleofluids and the atmosphere. This suggests intense groundwater circulation during the crystallization of ore minerals. The age of the rocks and ores of the Norilsk deposits was determined. The stage of orebody formation is restricted to a narrow age interval of 250 ± 10 Ma. An isotopic criterion was proposed for the ore-bearing potential of mafic intrusions in the Norilsk–Taimyr region. It includes several interrelated isotopic ratios of various elements: He, Ar, S, and others. 相似文献
14.
15.
16.
Mining induced subsidence can significantly affect mining costs where major surface facilities and natural environment need to be protected. Overburden grout injection is a technology used to control coal mine subsidence by injecting the mine waste material extracted from the coal back into the inter-burden rock during longwall mining. The flowing slurry is here categorised as a nonlinear viscous cohesive (Bingham plastic) fluid. During longwall mining the grout slurry is pumped into the separated beds of the rock mass through a central vertical borehole, which is drilled deep into the inter-burden rock strata above the coal seam. However, a blockage can occur in the injection system when the slurry velocity falls below a certain critical threshold velocity, indicating a material phase change from cohesive-viscous to cohesive-frictional. In situ field injection tests through boreholes have been simulated at a smaller scale at the CSIRO laboratory in Brisbane by pumping the slurry through a radial disk (gap = 4 mm) from its centre. Laboratory experiments indicate a general, nonlinear, cohesive, viscous, frictional model for shear behaviour of the slurry, in which the material shear parameters are functions of the disk radial distance. Complete dimensional and dimensionless analytical solutions have been developed based on an approach related to Bingham–Herschel–Bulkley fluid mechanics. The derived formulae include relations for minimum pump pressure, local pressure and pressure gradient, wall shear stress, volume rate, velocity and velocity gradient. The theoretical results match the experimental measurements. The experiments covered slurries with maximum particle sizes of 0.5 to 2 mm with about 50% being larger than 100 µm. The viscosities at the various solids concentrations were measured with a standard torsion viscometer. This study differs from the previous research in several distinct aspects, namely, consideration of the variable shear parameters rather than fixed values, inclusion of total nonlinear behaviour, and implementation of a friction function to mimic behaviour of the deposited and consolidating stiff slurry, which can cause a significant pressure rise as a result of the increased shear resistance. 相似文献
17.
18.
岩石密度和超高压岩石折返速率 总被引：1，自引：3，他引：1
在常温常压条件下对中国大陆科学钻CCSD主孔100-3000米岩心样品进行了密度测量,建立了密度连续剖面,并界定了不同超高压岩石的密度值。通过对比高温高压物性实验资料,岩石密度随着退变程度增强而降低,榴辉岩密度变化序列为3.52g/cm3→3.49g/cm3→3.07g/cm3→2.93g/cm3。超高压长英质岩石密度变化序列为3.00g/cm→2.80g/cm3→2.65g/cm3。上述实验资料是讨论不同折返阶段岩石所受浮力的基础,为研究折返速率大小提供了基本参数。本文通过折返板块运动平衡时,上浮力与粘滞力平衡这一关系式,定量研究了大陆俯冲板块的折返速率,认为密度差产生上浮力从而引起折返,温度对板块折返速率的影响最为显著;密度差大小、折返角度、折返板块大小对折返速率也有直接的影响。定量模拟分析表明,在温度高于850℃时,板块的折返速率可以超过100mm/a;当温度降至700℃时,折返速率则低于1.5mm/a。作者认为在折返早期,温度较高,板块快速折返至60-70km榴辉岩相深度;随着传导散热,温度降低,板块以较慢的速率折返至中下地壳。折返速率的估算表明,浮力是板块折返第一阶段(从>100km深部折返至<40km的中下地壳)的主要驱动力。 相似文献
19.
《Applied Geochemistry》2001,16(2):137-159
Five hundred and ninety-eight samples of terrestrial moss (Hylocomium splendens and Pleurozium schreberi) collected from a 188,000 km2 area of the central Barents region (NE Norway, N Finland, NW Russia) were analysed by ICP-AES and ICP-MS. Analytical results for Al, B, Ba, Ca, K, La, Mg, Mn, Na, P, Rb, Si, Sr, Th, U and Y concentrations are reported here. Graphical methods of data analysis, such as geochemical maps, cumulative frequency diagrams, boxplots and scatterplots, are used to interpret the origin of the patterns for these elements. None of the elements reported here are emitted in significant amounts from the smelting industry on the Kola Peninsula. Despite the conventional view that moss chemistry reflects atmospheric element input, the nature of the underlying mineral substrate (regolith or bedrock) is found to have a considerable influence on moss composition for several elements. This influence of the chemistry of the mineral substrate can take place in a variety of ways. (1) It can be completely natural, reflecting the ability of higher plants to take up elements from deep soil horizons and shed them with litterfall onto the surface. (2) It can result from naturally increased soil dust input where vegetation is scarce due to harsh climatic conditions for instance. Alternatively, substrate influence can be enhanced by human activity, such as open-cast mining, creation of ‘technogenic deserts’, or handling, transport and storage of ore and ore products, all of which magnify the natural elemental flux from bedrock to ground vegetation. Seaspray is another natural process affecting moss composition in the area (Mg, Na), and this is most visible in the Norwegian part of the study area. Presence or absence of some plant species, e.g., lichens, seems to influence moss chemistry. This is shown by the low concentrations of B or K in moss on the Finnish and Norwegian side of the (fenced) border with Russia, contrasting with high concentrations on the other side (intensive reindeer husbandry west of the border has selectively depleted the lichen population). 相似文献
20.
Marta L. PATINO-DOUCE Alberto PATINO-DOUCE Mazhar QAYYUM Roger L. NIELSEN 《Geostandards and Geoanalytical Research》1994,18(2):195-198
We have developed a set of four synthetic standards for the rare earth and high field strength elements designed for use in the determination of those elements in silicates. The base material is a glass nominally at the eutectic of the MgO-Al2 O3 -SiO2 ternary system. The nominal doping level was 2 wt% of the elements as oxides. To avoid problems associated with peak interference, the elements were doped in four separate glasses. 相似文献