共查询到20条相似文献，搜索用时 62 毫秒
1.
太湖MS岩芯重金属元素地球化学形态研究 总被引：21，自引：4，他引：17
采用BCR三步提取法对太湖MS岩芯沉积物中Cu、Fe、Mn、Ni、Pb和Zn等6种重金属元素的化学形态进行了研究.结果表明,有效结合态的Cu、Ni和Pb主要以有机物及硫化物结合态、Fe-Mn氧化物结合态存在,Fe和Zn主要以Fe-Mn氧化物结合态存在,Mn主要以可交换态及碳酸盐结合态存在;Fe-Mn氧化物结合态的Ni、Pb和Zn与可还原态的Mn有较好的正相关关系,有机物及硫化物结合态的Cu、Mn、Ni、Pb和Zn与有机碳含量有较好的正相关关系;重金属形态分布体现了重金属元素地球化学性质的差异,以及重金属形态含量与沉积物理化性质的关系.沉积岩芯重金属元素形态垂向变化规律及次生相富集系数表明,Cu、Mn、Ni、Pb和Zn在沉积岩芯13～4 cm有效结合态含量较稳定,为自然沉积;4～0 cm有效结合态含量明显升高,存在一定程度的人为污染.根据137Cs测年结果判断,沉积岩芯Cu、Mn、Ni、Pb和Zn等重金属污染开始于20世纪70年代末期,主要污染元素及污染历史与太湖流域污染工业类型及经济发展阶段相吻合. 相似文献
2.
湘江是我国重金属污染最严重的河流之一。本次工作利用X射线荧光(XRF)和电感耦合等离子质谱(ICP-MS)分析技术,对湘江竹埠港沉积物进行主量和微量元素分析。结果表明沉积物主量元素含量变化相对稳定,富集Mn O、P2O5、Fe2O3、Al2O3,亏损Ca O、Na2O。微量元素含量变化较大,亏损Ba、Sc、Mn、Sr而富集其他微量元素。对主量元素和稀土元素进行了分析,表明沉积物物源主要是由上游花岗岩风化所提供。对沉积物进行因子分析和相关性分析,表明沉积物源主要以陆源碎屑为主,并有磷灰石和软锰矿等自生副矿物,Ni、Pb、Cu可能来自人为污染源。地累积指数表明Ba为清洁无污染,重金属V、Cr、Co、Ni、Th、U为轻度污染,重金属Cu、Pb、Zn为偏中度污染,Mn为中度污染,Sc为偏重度污染。其中重金属Cr、Ni、Cu、Pb、Zn、Mn、Sc污染应引起关注。 相似文献
3.
近50年来抚仙湖重金属污染的沉积记录* 总被引：15，自引：8，他引：15
文章以抚仙湖污染严重的北部和基本未受人类活动影响的中部为研究对象,分别采集了沉积岩芯FB和FZ,通过对岩芯的137 Cs测年和重金属元素(Cu,Ni,Ti,Cr,V,Pb,Cd和Zn)的含量分析,研究了湖泊重金属来源和污染历史,并利用地质累积指数法评价了湖泊重金属污染程度。结果表明:抚仙湖北部的平均沉积速率约为2.0~2.8mm/a;20世纪80年代以前,湖泊北部和中部的重金属元素(Cu,Ni,Ti,V,Pb,Cd,Zn)以自然来源为主;80年代以后,抚仙湖受到人类活动的影响,但湖泊中部Cu,Ni,Ti,V,Pb,Zn以及湖泊北部Cu,Ni,Ti,V仍以自然来源为主;湖泊北部Pb和Zn地质累积指数值小于1,属无污染到中度污染;北部Cd地质累积指数为3~4,达强度污染;中部Cd地质累积指数为2~3,属中强度污染;且Pb,Zn和Cd污染程度有加速增大的趋势。 相似文献
4.
长江下游青弋江、水阳江水系湖泊沉积物中重金属变化特征研究 总被引：7，自引：5，他引：2
2004～2008年在青弋江、水阳江流域石臼、固城、南漪三湖采集得到岩芯钻孔.运用核素210Pb和137Cs对获得沉积物进行定年,同时分析了岩芯沉积物金属元素,研究近代湖泊重金属演化历史以及人类活动的影响,并对重金属进行了评价.文章运用Al元素作为粒度的代用指标对重金属进行标准化,并获取了重金属富集系数.研究表明,石臼、固城、南漪三湖钻孔中Cu和Zn的富集系数高于Pb,但Pb,Zn,Cu和Cr富集系数都不超过2,并且Cr的富集系数较小.自20世纪80年代中期以来流域内人类活动对石臼湖湖泊沉积物造成了显著的重金属污染,在南漪湖则推迟了10年左右,而在固城湖其重金属污染相对不明显.根据沉积物质量基准进行评价,发现石臼、固城、南漪三湖虽然存在一定的Cu,Pb,Zn和Cr污染,但污染造成的生态效应还不明显. 相似文献
5.
东太湖钻孔揭示的重金属污染历史 总被引：1，自引：0，他引：1
2009年在东太湖运用重力采样器采集得到岩芯钻孔(DJZ和DQG)。运用核素210Pb和137Cs对沉积物钻孔进行定年,同时分析了沉积物金属元素,并研究近代东太湖重金属污染以及人类活动对其的影响。本文运用Fe元素作为粒度的代用指标对重金属进行标准化,并获取了重金属富集系数和人为污染的重金属通量。研究表明,除了钻孔的表层样以外,东太湖DQG和DJZ钻孔的Pb、Zn、Cu、Cr和Ni的富集系数都不超过2,并且Cr、Ni的富集系数接近1。结果表明最近几十年来的重金属铅、铜、锌在不断富集,尤其是在20世纪70年代以来。20世纪70年代至90年代,东太湖来源于人为污染的Pb、Zn、Cu的通量维持在一定的水平,90年代以来,东太湖来源于人为污染的Pb、Zn、Cu的通量在不断增加,这与区域污染工业类型及经济发展阶段相吻合。东太湖2000s初以来Pb通量特别是人为污染的Pb的通量出现下降,这可能部分与含铅汽油的禁用有关,另外也与该阶段流域工业结构的调整有关。 相似文献
6.
《地球化学》2016,(1)
本研究用X射线荧光(XRF)和电感耦合等离子质谱仪(ICP-MS)等对湘江湘潭段河岸沉积物进行了主元素、微量元素地球化学分析。结果表明,河岸沉积物具明显贫Na_2O、CaO、Mg O等碱质,而富Fe_2O_3、MnO等氧化物的化学组成特征。沉积物明显富集Cu、Pb、Zn、Mn、V、Cr、U、Th等多种重金属和Zr、Hf、Ta等高强场元素,而亲石元素Cs、Ga、Ge、Rb、Sr等及稀土元素(REE+Y)在沉积物中富集不明显。地累积系数(Igeo)法评价显示,河岸沉积物存在Cu、Zn、Pb等元素组成的潜在重金属污染。主元素与重金属元素相关性分析显示,Ba、Rb、Th、U、Sc、Cr、Ta、Nb、Zr、Hf、Ga、Ge、Y等主要赋存于石英等碎屑矿物中,这些微量金属元素可能主要为自然来源,在沉积物中化学性质相对稳定;而Mn、V、Co、Cr、Cu、Pb、Zn等重金属元素则主要赋存于铁、锰氧化物矿物相中,这些重金属元素可能以人为源为主,在沉积物中有一定的化学活性,可发生活化迁移。沉积物的Fe_2O_3、LOI、∑REE等的含量值及Eu/Eu*值可作为指示沉积物重金属污染的地球化学指标,对沉积物重金属污染有一定的指示作用。 相似文献
7.
天津市潮间带柱状沉积物中重金属的污染历史及来源判别 总被引：3，自引：0，他引：3
利用因子分析和元素含量特征分析两种方法,对天津市潮间带的4个无扰动沉积物柱样的46个样品进行了重金属分析,并探讨了重金属的来源方式和富集原因。研究结果表明,天津市潮间带的重金属可分为3类:1)Fe、Cr、Al及Mn元素主要受环境背景值的影响,2)Hg和Cd受人为活动的影响较大,3)As、Zn、Pb、Cu及Ni受环境背景值及人类活动的双重影响,且影响大小随所在位置的不同而变化。结合210Pb和137Cs测年结果,定量确定了天津市潮间带小于0.063 mm粒级沉积物中Ni等11种重金属元素的环境背景值,并以此为基础,进一步探讨了重金属富集年代、富集量及污染历史和人类活动的关系,发现多数重金属的污染始于1910年代,并在1954年之后富集量增加。 相似文献
8.
厦门西港沉积环境变化及重金属的污染累积 总被引：1，自引：0，他引：1
通过测定柱状沉积物中的重金属、有机碳和硫化物含量, 结合沉积物粒度分析及现代沉积速率, 重现了厦门西港近70a的沉积环境变化及重金属的污染历史, 探讨了沉积环境对重金属累积过程的影响.结果表明, 厦门西港污染指示元素为Cu, Zn, Pb, As, 富集程度依次为As > Cu > Zn > Pb, 元素Cr, Cd和Hg在研究海域内没有富集现象.综观70a来, 厦门西港沉积物组成变化较大, 沉积环境变化明显, 重金属含量的垂向变化特征与当时的水动力、沉积环境变化紧密相关.研究表明, 沉积物来源越稳定, 沉积物粒径越小, 分选性越好, 则沉积物中重金属含量越高; 同时, 各层位的绝大部分重金属与有机碳和硫化物呈显著正相关关系. 相似文献
9.
雅鲁藏布江表层沉积物地球化学元素研究 总被引：4，自引：0，他引：4
雅鲁藏布江流域还没有大的工业污染源,仍然属于自然河流.对雅鲁藏布江16个表层沉积样品的全样、小于20μm 和小于63μm 粒级的32种元素含量进行了测定,并分析了与人类活动密切相关的元素 Cr、Mn、Fe、Co、Ni、Cu、Zn、As、Cd 和 Pb 的含量分布特征,以及这些元素含量与粒径之间的关系.结果表明,多数元素(Cs 除外)与西藏土壤元素背景值相差不大, B、Cr、Ni、As 和 Cs 含量高于中国陆壳元素丰度值,但这些元素主要来源于该流域富含这些元素的页岩、片岩和千枚岩等母岩.由于相似的地球化学行为,沉积物中 Cr、Mn、Fe、Co、Ni、Cu、Zn 之间显著正相关;除 Pb、As 外,一些元素(如 Zn、Ni)与沉积物的粒径显著负相关 相似文献
10.
宁沪高速公路句容段两侧土壤磁化率异常与重金属元素的关系研究 总被引：1，自引：0，他引：1
高速公路两侧土壤的磁化率从路中央向两侧具有逐渐降低的特征,相对应的样品中的重金属Cu、Pb、Zn、N i、Cr、Fe等元素的含量也具有从路中心向两侧逐渐降低的现象。相关分析表明,土壤磁化率与土壤中的Cu、Pb、Zn、N i、Cr、Fe的相关性显著,因而可以利用磁化率异常来指示高速公路两侧土壤的重金属污染状况。元素的赋存形态分析表明铁锰氧化物态与残渣态是Cu、Pb、Zn、N i、Cr、Fe的主要赋存形式;各元素的形态分析结果与土壤磁化率的相关统计分析表明,高速公路两侧土壤的磁化率与可交换态中的Cu、Pb、Zn、铁锰氧化物态中的Fe、Pb、Zn、有机还原态中的Cu、Cr、Fe、Zn和残渣态中的Cu、Pb、Zn、Cr、Co、N i具有明显的相关性。 相似文献
11.
S. Viswanathan K. Surya Prakash Rao B. Mahabaleswar 《Journal of the Geological Society of India》2013,82(6):621-627
Komatiites are mantle-derived ultramafic volcanic rocks. Komatiites have been discovered in several States of India, notably in Karnataka. Studies on the distribution of trace-elements in the komatiites of India are very few. This paper proposes a simple, accurate, precise, rapid, and non-destructive wavelength-dispersive x-ray fluorescence (WDXRF) spectrometric technique for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in komatiites, and discusses the accuracy, precision, limits of detection, x-ray spectral-line interferences, inter-element effects, speed, advantages, and limitations of the technique. The accuracy of the technique is excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Zr, Nb, Ba, Pb, and Th and very good (within 4%) for Y. The precision is also excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th. The limits of detection are: 1 ppm for Sc and V; 2 ppm for Cr, Co, and Ni; 3 ppm for Cu, Zn, Rb, and Sr; 4 ppm for Y and Zr; 6 ppm for Nb; 10 ppm for Ba; 13 ppm for Pb; and 14 ppm for Th. The time taken for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in a batch of 24 samples of komatiites, for a replication of four analyses per sample, by one operator, using a manual WDXRF spectrometer, is only 60 hours. 相似文献
12.
奥地利安东帕有限公司 《岩矿测试》2009,28(3):306-306
最新的流行病学研究表明,空气中较高浓度的悬浮细颗粒可能对人类的健康有不利的影响。根据该项研究显示,由于心脏病、慢性呼吸问题和肺功能指标恶化而导致死亡率的升高与细尘粒子有关。这些研究结果已经促使欧盟于1999年4月出台了限制空气中二氧化硫、二氧化氮、氧化氮、铅和颗粒物含量的法案(1999/30/EC),对各项指标包括对可吸入PM10颗粒的浓度提出了新的限制性指标。PM10颗粒是指可以通过预分级器分离采集的气体动力学直径小于10μm的细颗粒。目前研究的兴趣重点逐步偏向PM2.5这些更细微颗粒物,PM2.5这种颗粒物对健康有明显的不利影响。在欧盟指令2008/50/EC中,对PM10和PM2.5都提 相似文献
13.
14.
E. M. Prasolov S. A. Sergeev B. V. Belyatsky E. S. Bogomolov K. A. Gruzdov I. N. Kapitonov R. Sh. Krymsky V. O. Khalenev 《Geochemistry International》2018,56(1):46-64
This paper reports the first results of a study of 11 isotope systems (3He/4He, 40Ar/36Ar, 34S/32S, 65Cu/63Cu, 62Ni/60Ni, 87Sr/86Sr, 143Nd/144Nd, 206–208Pb/204Pb, Hf–Nd, U–Pb, and Re–Os) in the rocks and ores of the Cu–Ni–PGE deposits of the Norilsk ore district. Almost all the results were obtained at the Center of Isotopic Research of the Karpinskii All-Russia Research Institute of Geology. The use of a number of independent genetic isotopic signatures and comprehensive isotopic knowledge provided a methodic basis for the interpretation of approximately 5000 isotopic analyses of various elements. The presence of materials from two sources, crust and mantle, was detected in the composition of the rocks and ores. The contribution of the crustal source is especially significant in the paleofluids (gas–liquid microinclusions) of the ore-forming medium. Crustal solutions were probably a transport medium during ore formation. Air argon is dominant in the ores, which indicates a connection between the paleofluids and the atmosphere. This suggests intense groundwater circulation during the crystallization of ore minerals. The age of the rocks and ores of the Norilsk deposits was determined. The stage of orebody formation is restricted to a narrow age interval of 250 ± 10 Ma. An isotopic criterion was proposed for the ore-bearing potential of mafic intrusions in the Norilsk–Taimyr region. It includes several interrelated isotopic ratios of various elements: He, Ar, S, and others. 相似文献
15.
Mining induced subsidence can significantly affect mining costs where major surface facilities and natural environment need to be protected. Overburden grout injection is a technology used to control coal mine subsidence by injecting the mine waste material extracted from the coal back into the inter-burden rock during longwall mining. The flowing slurry is here categorised as a nonlinear viscous cohesive (Bingham plastic) fluid. During longwall mining the grout slurry is pumped into the separated beds of the rock mass through a central vertical borehole, which is drilled deep into the inter-burden rock strata above the coal seam. However, a blockage can occur in the injection system when the slurry velocity falls below a certain critical threshold velocity, indicating a material phase change from cohesive-viscous to cohesive-frictional. In situ field injection tests through boreholes have been simulated at a smaller scale at the CSIRO laboratory in Brisbane by pumping the slurry through a radial disk (gap = 4 mm) from its centre. Laboratory experiments indicate a general, nonlinear, cohesive, viscous, frictional model for shear behaviour of the slurry, in which the material shear parameters are functions of the disk radial distance. Complete dimensional and dimensionless analytical solutions have been developed based on an approach related to Bingham–Herschel–Bulkley fluid mechanics. The derived formulae include relations for minimum pump pressure, local pressure and pressure gradient, wall shear stress, volume rate, velocity and velocity gradient. The theoretical results match the experimental measurements. The experiments covered slurries with maximum particle sizes of 0.5 to 2 mm with about 50% being larger than 100 µm. The viscosities at the various solids concentrations were measured with a standard torsion viscometer. This study differs from the previous research in several distinct aspects, namely, consideration of the variable shear parameters rather than fixed values, inclusion of total nonlinear behaviour, and implementation of a friction function to mimic behaviour of the deposited and consolidating stiff slurry, which can cause a significant pressure rise as a result of the increased shear resistance. 相似文献
16.
17.
Alexander E. C. Broberg J. S. Kehren A. R. Graziani M. M. Turri W. L. 《Environmental Geology》1993,22(4):353-361
Bellechester, Minnesota, is a small community of approximately 155 residents located on the county line between Goodhue and Wabasha counties in southeast Minnesota's karst region. Bellechester is served by a 21-year-old wastewater treatment facility (WWTF) consisting of three waste-stabilization ponds. On 28 April 1992 six sinkholes were discovered to have drained cell 2 of the WWTF resulting in the loss of approximately 8.7×106 1 of partially treated effluent and about 600 m3 of soil into previously undetected subsurface voids of unknown dimensions. In the week following the collapse, approximately 200 water wells located within a 5-km radius of the WWTF were sampled in an after-the-fact, emergency sampling program. Twelve samples with elevated fecal coliform levels, 18 samples with nitrate-nitrogen greater than the 10 mg/1 standard, and no samples with elevated chlorides were found. However, the elevated levels could not be unambiguously attributed to the WWTF collapse. This is the third WWTF to fail by sinkhole collapse in southeast Minnesota since 1974. All three collapsed lagoons have been located in similar geomorphic and stratigraphic settings. However, at least two lagoons have collapsed in the adjacent area in northeast Iowa, and these lagoons are located at different stratigraphic positions. Twenty-two WWTFs constructed in southeast Minnesota's karst region in the last 25 years have been identified as subject to potential sinkhole collapse. An unknown but significant number of manure storage lagoons, flood control structures, etc., have also been constructed in the karst region and are at risk. Public agencies are beginning to develop plans to deal with the risk associated with existing and future waste lagoons in this environment. The critical hydrogeologic parameters that can be used to prioritize the risk of collapse at existing facilities include: (1) the lithology of the first bedrock beneath each lagoon, (2) the thickness of surficial materials between the lagoon and the bedrock surface, (3) the presence and construction of liners (seepage rate), and (4) the proximity to existing sinkholes. 相似文献
18.
Mercury,arsenic, antimony,and selenium contents of sediment from the Kuskokwim River,Bethel, Alaska,USA 总被引：1，自引：0，他引：1
The Kuskokwim River at Bethel, Alaska, drains a major mercury-antimony metallogenic province in its upper reaches and tributaries. Bethel (population 4000) is situated on the Kuskokwim floodplain and also draws its water supply from wells located in river-deposited sediment. A boring through overbank and floodplain sediment has provided material to establish a baseline datum for sediment-hosted heavy metals. Mercury (total), arsenic, antimony, and selenium contents were determined; aluminum was also determined and used as normalizing factor. The contents of the heavy metals were relatively constant with depth and do not reflect any potential enrichment from upstream contaminant sources. 相似文献
19.
滇东南锡、银、铅、锌多金属矿床主要分布在个旧、白牛厂、都龙3个矿区,而滇东南较大的3个花岗岩体又分别出露在3个矿区或附近.花岗岩体均形成于燕山晚期,岩石化学、矿物成分相似,富含锡、银、铅、锌、钨、铜等成矿元素.矿床主金属元素组合与岩体之间的距离由远而近出现由锡、钨、(铍、铌、钽)→锡、钨、(铁)、铜、铟→锡、铅、锌、银、铟、(锑)有规律的变化.花岗岩浆是成矿物质来源和成矿热源.岩浆侵入初期使上覆地层隆起产生背斜(凹陷部位成向斜);同时使地层产生一系列裂隙、压性断层或层间断裂;岩浆侵入晚期,这些断层再次活动,表现为张性,岩浆产生的含矿热液沿由其活动所造成的断裂迁移、充填、交代、沉淀而形成矿床. 相似文献
20.
岩石密度和超高压岩石折返速率 总被引：1，自引：3，他引：1
在常温常压条件下对中国大陆科学钻CCSD主孔100-3000米岩心样品进行了密度测量,建立了密度连续剖面,并界定了不同超高压岩石的密度值。通过对比高温高压物性实验资料,岩石密度随着退变程度增强而降低,榴辉岩密度变化序列为3.52g/cm3→3.49g/cm3→3.07g/cm3→2.93g/cm3。超高压长英质岩石密度变化序列为3.00g/cm→2.80g/cm3→2.65g/cm3。上述实验资料是讨论不同折返阶段岩石所受浮力的基础,为研究折返速率大小提供了基本参数。本文通过折返板块运动平衡时,上浮力与粘滞力平衡这一关系式,定量研究了大陆俯冲板块的折返速率,认为密度差产生上浮力从而引起折返,温度对板块折返速率的影响最为显著;密度差大小、折返角度、折返板块大小对折返速率也有直接的影响。定量模拟分析表明,在温度高于850℃时,板块的折返速率可以超过100mm/a;当温度降至700℃时,折返速率则低于1.5mm/a。作者认为在折返早期,温度较高,板块快速折返至60-70km榴辉岩相深度;随着传导散热,温度降低,板块以较慢的速率折返至中下地壳。折返速率的估算表明,浮力是板块折返第一阶段(从>100km深部折返至<40km的中下地壳)的主要驱动力。 相似文献