Large debris flows in Chosica,Lima, Peru: the application of hydraulic infrastructure for erosion control and disaster prevention     

S. P. Villacorta  K. G. Evans  K. Nakatani  I. Villanueva 《Australian Journal of Earth Sciences》2020,67(3):425-436

Abstract

Large debris flows in steep-sloped ravines debouching to the Rimac River, in metropolitan Lima (Peruvian capital), have resulted in considerable loss of life and property adversely impacting communities in the region. Temporal, spatial and volumetric features of debris flows are difficult to predict, and it is of utmost importance that achievable management solutions are found to reduce the impact of these catastrophic events. The emotional and economic toll of these debris flows on this increasingly densely populated capital city in South America is devastating where communities must live in such inadequate and dangerous conditions. To address this problem, the application of advanced Japanese technology, Sustainable Actions Basin Orientation (SABO), has been investigated using a geomorphological modelling to develop an implementation plan. Rayos de Sol stream basin in Chosica, was selected as a pilot to develop the proposal, as it is considered high risk due to the presence of ancient debris flows and recent flows in 2012, 2015 and 2017. The recurrence of debris flows in this location has resulted in numerous deaths and catastrophic property losses. This study combines geologic and geomorphic mapping and hydraulic and landform evolution numerical modelling. The implementation of a SABO Master Plan based on the multidisciplinary assessment hazard scenarios, will allow the implementation of feasible mitigation actions. The SABO technology has been applied successfully in Japan and other countries in areas with steep short slopes, similar to the conditions surrounding the Peruvian capital. Results from this study will be presented to the Peruvian Government as part of an action plan to manage debris-flow impact.

1. KEY POINTS

2. High-risk mass slope failure is linked to poor urban planning in urban developing regions of Lima the capital of Peru.

3. A multidisciplinary study including geotechnical and hydrological analysis, engineering design, and socio-economic research is required to implement a SABO Master Plan, and this basin is pilot study basin.

4. At the present time, a maintenance programme for existing hydraulic structures should be implemented, and a flood risk management plan developed may propose the relocation of some communities and infrastructure.

  相似文献   

地震应急指挥中心可视化中控系统的设计与实现     

林向洋  文鑫涛  高小跃  甄盟  郑通彦 《地震地磁观测与研究》2020,41(4):225-231

介绍地震应急指挥中心中控系统的建设情况，阐述了可视化智能中控系统的功能需求、逻辑结构和应用框架结构，分析了可视化智能中控系统的功能特点，并对中控系统的技术发展和应用进行展望。  相似文献   

基于能量原理的粘滞阻尼器附加阻尼系数分配方法研究          下载免费PDF全文

王子龙  任文杰  杨新磊  陈博文 《世界地震工程》2020,(3):027-37

以线性粘滞阻尼器加固剪切型规则框架结构为研究对象，基于能量原理提出附加阻尼系数正比于层间位移平方的分配方式。以六层和十二层钢筋混凝土框架为例，以确保结构在中震时保持弹性状态为设计目标，分别采用附加阻尼系数正比于层间位移平方的分配方式以及现有的分配方式，对结构进行消能减震设计。计算结果表明:有控结构均满足中震不坏的要求，层间位移角限值均未超过1/550，减震效果良好；附加阻尼系数正比于层间位移平方的分配方式得出的总阻尼系数最小，为最经济的设计结果。  相似文献   

First Multi‐Isotopic (Pb‐Nd‐Sr‐Zn‐Cu‐Fe) Characterisation of Dust Reference Materials (ATD and BCR‐723): A Multi‐Column Chromatographic Method Optimised to Trace Mineral and Anthropogenic Dust Sources     

Aubry Vanderstraeten  Steeve Bonneville  Stefania Gili  Jeroen de Jong  Wendy Debouge  Philippe Claeys  Nadine Mattielli 《Geostandards and Geoanalytical Research》2020,44(2):307-329

Atmospheric dust is an integral component of the Earth system with major implications for the climate, biosphere and public health. In this context, identifying and quantifying the provenance and the processes generating the various types of dust found in the atmosphere is paramount. Isotopic signatures of Pb, Nd, Sr, Zn, Cu and Fe are commonly used as sensitive geochemical tracers. However, their combined use is limited by the lack of (a) a dedicated chromatographic protocol to separate the six elements of interest for low‐mass samples and (b) specific reference materials for dust. Indeed, our work shows that USGS rock reference materials BHVO‐2, AGV‐2 and G‐2 are not applicable as substitute reference materials for dust. We characterised the isotopic signatures of these six elements in dust reference materials ATD and BCR‐723, representatives of natural and urban environments, respectively. To achieve this, we developed a specific procedure for dust, applicable in the 4–25 mg mass range, to separate the six elements using a multi‐column ion‐exchange chromatographic method and MC‐ICP‐MS measurements.  相似文献   

地缘政治视角下中亚“颜色革命”易发程度分析     

李希雅  王礼茂 《世界地理研究》2019,28(6):42-49

基于地缘政治视角，分析本世纪初发生在原苏联地区“颜色革命”的诱发因素，认为美国根据其地缘战略格局对“颜色革命”发生地存在一定程度的主观选择性，国家内部经济、政治、社会等层面的矛盾也同样作为发生背景。在中亚地缘格局动态分析的基础上，结合中亚五国形势，从时间和空间双重维度对中亚地区未来发生“颜色革命”的可能性进行识别与评判，得出1) 整体来看，中亚近期内爆发“颜色革命”可能性较小，但从长远来看不能掉以轻心。2)土、乌未来稳定可期，塔、吉、哈需谨防“颜色革命”卷土重来。  相似文献   

利用InSAR资料反演宁洱Ms6.4地震震源参数及库仑应力变化     

陈晨月  冯光财  高华  杨怀宁 《大地测量与地球动力学》2019,39(3):295-301

首先利用ALOS PALSAR数据，通过D-InSAR技术获取2007-06-03云南宁洱MS6.4地震的同震形变场，然后基于Okada弹性半空间位错模型反演该地震的断层几何以及精细滑动分布，最后计算宁洱地震后周边断层的静态库仑应力变化。结果表明，形变主要集中在西盘，最大视线向形变量为51.6 cm；反演得到的震源位置为23.05°N、101.02°E，深度3 km，断层走向145°，倾向49.5°，平均滑动角153°，发震断层为NNW向普洱断裂，断层活动以右旋走滑为主，兼具逆冲分量；断层面最大滑动量为1.2 m，反演得到的震级为MW619。基于库仑应力场发现，磨黑断裂处于库仑应力增加区域，而2014年景谷地震位于负值区域。结合实地考察资料和反演结果表明，宁洱地震为浅源地震，但断层并未出露地表。  相似文献   

基于GPS和水准数据的微粒群算法联合反演祁连山北缘断裂三维滑动速率     

刘杰 《大地测量与地球动力学》2019,39(9):906-909

将微粒群算法与位错理论模型相结合，采用中国地壳运动观测网络提供的青藏高原地区2001~2004年GPS测量数据和2000~2006年水准测量数据，通过常规定权和附有相对权比的方法对祁连山北缘断裂的三维滑动速率进行联合反演，并与蚁群算法反演结果进行对比。结果表明，微粒群算法收敛速度快、稳定性高，结合经典位错理论模型，是一种可以有效求解断层三维滑动速率反演问题的优化算法，在大地测量反演领域极具应用潜力。  相似文献   

Experimental investigation on a cabin-suspended catamaran in terms of motion reduction and wave energy harvesting by means of a semi-active motion control system     

《Applied Ocean Research》2019

A novel concept catamaran equipped with a suspended cabin, named Wave Harmonizer Type 4 (WHzer-4), is proposed and evaluated. The mass-spring-mass system is constructed by mounting four sets of suspensions in-between the cabin and the twin-hull. Two sets of dual motor/generators (M/Gs) are attached on the center beam of the cabin's deck fore and aft. Each shaft-end of the dual M/Gs is connected to the twin-hull through a rack-pinion gear unit. In this way the vertical relative motion between the cabin and the twin-hull can be transferred into the rotational motion of the M/Gs, and vice versa. A semi-active motion control system, which contains a proportional-integral (PI) controller, is designed and applied to each of the dual M/Gs for the aim of absorbing wave energy under the condition of suppressing the local vertical velocity of the cabin as much as possible. A 1/5 scale model ship with a length of 1.6 m is built, and a forced-oscillation bench test is implemented to validate the performance of the control system. Then, a series of towing tank tests is carried out in regular head waves. The heave and pitch responses of the cabin, those of the twin-hull and the corresponding wave energy capture width ratio (CWR) at five control scenarios and two reference scenarios are investigated. Discussion on the results of the tank test shows that the motion reduction of the cabin and the wave energy harvesting can be achieved simultaneously at a few wave conditions. However, at other conditions, although noticeable amount of wave energy is harvested, motion reduction of the heave and pitch of the cabin could not be obtained at the same time. It is suggested that varying the gain settings of the PI controllers according to the location of the controllers may improve the effectiveness of the proposed control system.  相似文献   

Adsorption Mechanism and Kinetic Characterization of Bituminous Coal under High Temperatures and Pressures in the Linxing-Shenfu Area     

TAO Chuanqi  WANG Yanbin  LI Yong  NI Xiaoming  GAO Xiangdong 《《地质学报》英文版》2020,94(2):399-408

The majority of coalbed methane(CBM) in coal reservoirs is in adsorption states in coal matrix pores. To reveal the adsorption behavior of bituminous coal under high-temperature and high-pressure conditions and to discuss the microscopic control mechanism affecting the adsorption characteristics, isothermal adsorption experiments under hightemperature and high-pressure conditions, low-temperature liquid nitrogen adsorption-desorption experiments and CO2 adsorption experiments were performed on coal samples. Results show that the adsorption capacity of coal is comprehensively controlled by the maximum vitrinite reflectance(Ro, max), as well as temperature and pressure conditions. As the vitrinite reflectance increases, the adsorption capacity of coal increases. At low pressures, the pressure has a significant effect on the positive effect of adsorption, but the effect of temperature is relatively weak. As the pressure increases, the effect of temperature on the negative effect of adsorption gradually becomes apparent, and the influence of pressure gradually decreases. Considering pore volumes of pores with diameters of 1.7-100 nm, the peak volume of pores with diameters 10-100 nm is higher than that from pores with diameters 1.7-10 nm, especially for pores with diameters of 40-60 nm, indicating that pores with diameters of 10-100 nm are the main contributors to the pore volume. The pore specific surface area shows multiple peaks, and the peak value appears for pore diameters of 2-3 nm, indicating that this pore diameter is the main contributor to the specific surface area. For pore diameters of 0.489-1.083 nm, the pore size distribution is bimodal, with peak values at 0.56-0.62 nm and 0.82-0.88 nm. The adsorption capability of the coal reservoir depends on the development degree of the supermicroporous specific surface area, because the supermicroporous pores are the main contributors to the specific pore area. Additionally, the adsorption space increases as the adsorption equilibrium pressure increases. Under the same pressure, as the maximum vitrinite reflectance increases, the adsorption space increases. In addition, the cumulative reduction in the surface free energy increases as the maximum vitrinite reflectance increases. Furthermore, as the pressure increases, the surface free energy of each pressure point gradually decreases, indicating that as the pressure increases, it is increasingly difficult to adsorb methane molecules.  相似文献   

深渊着陆器坐底位置的精确测量和反演计算          下载免费PDF全文

陈瀚  丘学林  贺恩远  王元  陈传绪  陈俊 《地球物理学报》2019,62(5):1744-1754

深渊着陆器在下潜过程中,由于受到海流的影响,其坐底位置会偏离投放点,偏离量和偏离方向很难估计,而声学水下定位方法在深渊海区不太适用.通过在海面进行气枪十字放炮作业,利用炮点准确位置和时间信息,以及海底地震仪(Ocean Bottom Seismometer,OBS)记录的直达水波到时,对深渊着陆器的坐底位置进行精确测量可以提供有效定位数据.该方法对采集得到的数据进行预处理,使用蒙托卡洛方法结合最小二乘法,对万泉号着陆器实际坐底位置进行了反演校正,得到三个潜次的位置校正偏移量分别为211m、178m、861m,偏移方向各不相同,校正精度为±20m,比以往的定位精度大为提高.此外,该方法测量确定了三个海底标志物的精确位置,为未来万米无人或载人潜器提供了可靠的水下参考坐标.  相似文献