共查询到20条相似文献，搜索用时 46 毫秒
1.
搭建了光纤布里渊频移测量系统,实现了色散位移光纤20 ℃到820 ℃布里渊频移的测量,并对测量数据进行拟合. 在环境温度大范围变化时,目前采用的布里渊频移-温度一阶线性关系式对测量数据分析误差较大,针对这个问题,本文从纯石英光纤的结构特点和材料的物性系数出发,在分析光纤的热膨胀系数、光纤密度、折射率、弹性模量和泊松比与宽范围温度关系的基础上,根据布里渊频移与各物性参数的关系式理论推导了宽范围温度变化与布里渊频移之间的二次项关系式. 理论推导结果与实验数据基本符合,验证了理论分析的正确性,从而为光纤宽范围布 相似文献
2.
近海水域漫衰减系数的估算 总被引：1，自引：0，他引：1
海洋学家们将赛克圆盘深度作为一个描述海洋光学特性的基本参数——海洋水体透明度来测量,即通过观测白色赛克圆盘的反射光及圆盘以上水柱的散射光与其周围海水散射光的对比度的平衡来确定其深度.这个物理量涉及了白昼光在海水中垂直向下和垂直向上的两个传播过程,它反映了海水的混浊度.赛克圆盘深度测量是海洋调查中的一项基本的常规观测项目,它在水团分析、流系识别以及海洋光合作用测定等方面都具有 相似文献
3.
外差激光雷达测量水体布里渊散射可行性研究 总被引：1，自引：0，他引：1
该文分析外差激光雷达测量水体布里渊散射的可行性。借助测量水体布里渊散射的频移 ,可得到水体声速或温度。文中利用两条 12 7I2 吸收线锁定激光输出频率 ,产生稳定的频差约为7.5 GHz发射激光和激光本振。通过对 12 7I2 吸收线稳定度、激光频率稳定度、系统信噪比和反演精度的分析和计算机模拟 ,得出水体深度 2 5 m以内水体布里渊散射频移的测量误差可以控制在2 .5 MHz以内 ,达到水中声速 0 .6 m/ s或温度 0 .1℃的测量精度。 相似文献
4.
感应式温盐传感器基于电导率法测盐,可以实现现场测量与实时测量。测量盐度时需要首先计算海水温度、海水电导率和海水压力,表层感应式温盐传感器对压力量不予考虑,温度、电导率的精度却直接关系到盐度测量结果的准确度,因此使用传感器前必须进行温度和盐度的标定。分析了温盐传感器的工作原理,设计温度、电导率的标定校准步骤,包括回归曲线的选择和回归方程系数的计算,其中温度、电导率和温度补偿的标定回归曲线采用多项式形式,用实验室高精度盐度计和铂电阻温度仪测得5~7组数据,然后对多项式最小二乘法回归,电导率回归过程中由温度和盐度求电导率用到了二分法,最后论述了标定回归方程的误差范围。 相似文献
5.
6.
引言 海水电导率温度效应的资料,对于通过现场海水盐度—温度—深度(STD)测量给出的温度、电导和压力数据来确定盐度是重要的。这对于许多实验室的工作也是需要的。例如用一个实验室盐度计为基准进行电导测量装置的校正。在海洋测量中常用的函数是电导率R_(s.t.P) 相似文献
7.
8.
9.
三种微纳光纤环形腔海水盐度传感器理论研究 总被引：1，自引：0，他引：1
《中国海洋大学学报(自然科学版)》2015,(7)
盐度在研究海水水体密度、水质监测、海洋渔业等方面发挥着重要的作用,为发展一种新型的光学传感器来进行海水盐度的测量。从理论上设计3种温度不敏感的微纳光纤环形腔海水盐度传感器并进行了数值计算。利用有限元软件COMSOL计算了微纳光纤中传输的基模有效折射率,结合MATLAB对盐度传感器的特征参量进行数值研究。首先,研究了传感器的温度特性,得到了温度不敏感条件对应下的光纤半径。其次,研究了温度不敏感下传感器的灵敏度和探测极限。结果表明,在选择MgF2为镀膜材料的情况下,通过优化传感器参数,盐度灵敏度可达到0.02nm,盐度探测极限可达到0.18。本文结果可以为微纳光纤环形腔应用于海水盐度测量提供理论依据。 相似文献
10.
针对我国对海水温度剖面的测量需求,在分析已有方法优缺点的基础上提出了一种新的方法——光纤温度剖面连续测量系统.此测量系统以光纤光栅传感器为测量单元,采用波分复用的方式串接在一起组成船载拖曳链,再通过甲板上的解调终端实时显示所测物理参量,从而实现分布式实时测量.这种方法能够以低成本快速高效获得高分辨率的海水温度剖面分布情况,为海洋探测提供丰富有效的数据.课题组设计制作了拖曳链系统的甲板机及60 m长的拖曳链,并在青岛近海进行了拖曳海试,实时获取了试验数据,达到了预期效果. 相似文献
11.
Chandralata Raghukumar G. Sheelu P. A. Loka Bharathi Shanta Nair C. Mohandass 《Marine Georesources & Geotechnology》2001,19(1):1-16
In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance. 相似文献
12.
海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。 相似文献
13.
Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification
An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm. 相似文献
14.
Derek V. Ellis 《Marine Georesources & Geotechnology》2001,19(1):51-63
This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested. 相似文献
15.
G. Parthiban 《Marine Georesources & Geotechnology》2000,18(3):223-235
Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement. 相似文献
16.
17.
18.
Phylogenetic diversity and phenotypic characterization of cultivable bacterioplankton isolated from polar oceans 总被引：1，自引：0，他引：1
A set of 27 marine planktonic bacteria isolated from the polar regions was characterized by 16S rDNA sequencing and physiological and biochemical testing. More than half of these bacteria were positive for caseinase, gelatinase and 13-glucosidase, and could utilize glucose, maltose or malic acid as carbon source for cell growth. Twelve isolates expressed nitrate reduction activities. Except for one antarctic isolate BSwlO175 belonging to Actinobacteria phylum, these isolates were classified as γ-Proteobacteria, suggesting that γ-Proteobacteria dominated in cultivable marine bacterioplankton at both poles. Genus Pseudoalteromonas was the predominant group in the Chukchi Sea and the Bering Sea, and genus ShewaneUa dominated in cultivable bacterioplankton in the Prydz Bay. With sequence similarities above 97%, genus Psychrobacter was found at both poles. These 27 isolates were psychrotolerant, and significant 16S rDNA sequence similarities were found not only between arctic and antarctic marine bacteria （ 〉 99% ）, but also between polar marine bacteria and bacteria from other aquatic environments （ ≥ 98.8% ）, including temperate ocean, deep sea, pond and lake, suggesting that in the polar oceans less temperature-sensitive bacteria may be cosmopolitan and have a bipolar, even global, distribution at the species level. 相似文献
19.
The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments. 相似文献
20.
Oedometer tests have been carried out on 70 undisturbed surficial clays (at approximately 250 mm below the mudline), mostly collected by free-fall corers from sites widely scattered throughout the deep-sea North Atlantic. Acoustic measurements were also made, initially on contiguous samples and ultimately on the same sample using a geophysically instrumented oedometer which also collected electrical resistivity data. Apart from those quiescent areas below the carbonate compensation depth, such as north of the West Indies where very fine clays exist, most of the samples are silty clays whose geotechnical-geophysical properties are dependent on the type of clay minerals present (and their ability to take in moisture), the sand-size fraction, and the quantity of carbonate present. Thus the pure clays have high compressibilities which decrease on the addition of coarse particles, while the converse is true for the acoustic parameters, these increasing with the sand fraction. Using the notion of the intrinsic compression line for all samples, and comparison to it of the measured compression curves, it is clear that, contrary to some previously held ideas, most deep-sea clays are normally consolidated; the addition of carbonate has the effect of creating an open, stronger sediment skeleton. Interestingly, where information is available, the variation with depth of a sample's acoustic velocity follows the void ratio pressure relationship of the compression curve. This allows the construction of an in-situ sediment compression curve using the in-situ geophysical observations. 相似文献