共查询到20条相似文献，搜索用时 46 毫秒
1.
We used illite and chlorite crystallinities, index minerals, mineral assemblages, polytype and domain size of white mica, electron microprobe analysis (EMPA), b0 geobarometer and chlorite geothermometer to quantify the diagenetic and metamorphic overprint on the Triassic flysch formations in the Songpan-Garzê orogen along profile Zoigê-Lushan, northwest Sichuan. Two anchizones, two epizones, one diagenetic zone and a transition belt in-between them are defined on the basis of the obtained data. Illite crystallinity correlates strongly with the best mean domain size of mica and moderately with chlorite crystallinity. 2M1 white mica polytype are observed within the epizone whilst 2M1 and 1M polytypes occur in the anchizone and diagenetic zone. Epizonal metamorphism reached maximum temperatures of 370oC±21oC at low-to intermediate pressure conditions. Clay minerals underwent Ostwald ripening during metamorphism. Rocks from both sides of the Longmenshan fault reveal contrasting degrees of metamorphic overprint: on the northwest side of the Longmenshan fault, epimetamorphic conditions contrast with diagenetic rocks on the southeast side. 相似文献
2.
This study uses illite crystallinity,chlorite crystallinity,illite polytypes,the b_0 cell-dimension of K-white mica,clay mineral assemblages and mineral geothermo-geobarometers to investigate the overprint of diagenesis and metamorphism on the Meso-Neoproterozoic and the Lower Paleozoic along the profile Yueyang-Linxiang in northeastern Hunan Province,China.Illite crystallinity Kbler index(KI) of the 2μm fractions ranges from 0.225 to 0.485°Δ2θ while chlorite crystallinity Arkai index(AI) ranges from 0.244 to 1.500°Δ2θ.This indicates that the Meso-Neoproterozoic and the Lower Paleozoic along the profile Yueyang-Linxiang were overprinted with diagenesis and anchi- to epimetamorphism.Peak metamorphic temperature is estimated with the IV site chlorite geothermometer roughly at 360℃.The b_0 cell dimension values of illites(K-mica) range from 0.9002 to 0.9054 nm and,on average,at 0.9030 nm for the Meso-Neoproterozoic.Based on cumulative frequency curves of illite(K-mica) b_0 cell dimension,the peak metamorphic pressure of the MesoNeoproterozoic along the profile Yueyang-Linxiang is derived of an intermediate pressure type.Most illites occur in the 2M_1 polytype and some of them in a mixture of 2M1+1M types especially those in the Paleozoic.This result partly agrees with the conclusion of the lower greenschist and greenschist facies of the Lengjiaxi and Banxi Groups.However,it is not agreed with the sedimentary cover from the Sinian to the Lower Paleozoic or from the Banxi Group to the Lower Paleozoic.Crustal thickening due to "collision" between the Yangtze and Cathaysia blocks led to an increase in the thickness of the Meso-Neoproterozoic to ca.14 km and resulted in a temperature increase in those rocks due to burial.The very low grade to low grade metamorphism overprinting the Meso-Neoproterozoic implies that the so called "Chiangnania or Jiangnan orogen" was no relative with the "Grenvillian orogeney;instead,it might be a continuous amalgamation product between the Yangtze and Cathaysia blocks. 相似文献
3.
The metamorphic conditions of the Upper Permian Yangjiagou Formation in eastern Changchun, China, were evaluated based on the mineral assemblage, illite crystallinity, illite polytypism,the b dimension of illite, and the chemical composition of chlorite. The pelitic rocks in the Yangjiagou Formation are characterized by illite + kaolinite + chlorite ± mixed-layer chlorite/smectite and detrital quartz + plagioclase. Illite in the formation has a crystallinity of 0.38-0.55 and comprises mixed 2 M_1 and1 M_d polytypes, indicating a metamorphic temperature of 200℃. Based on the chemical composition of chlorite and the chlorite geothermometer, we estimated diagenetic to very low-grade metamorphic conditions with temperatures of 185℃～204℃. The b dimension of illite varies from 8.992 A to 9.005 A.We used a mathematical algorithm to extend Guidotti and Sassi's(1986) diagram relating illite b dimension with temperature and pressure, and used this diagram, together with illite crystallinity and chlorite chemical composition, to semi-quantitatively estimate the formation pressure at1.2 kbar. These reveal that the Yangjiagou Formation has experienced very low-grade metamorphism. 相似文献
4.
TANG Yan SANG Longkang YUAN Yanming YU Jishun ZHANG Yunpeng QI Xianmao YANG Yunlong 《《地质学报》英文版》2012,86(1):96-105
X-ray diffraction methods for estimating the metamorphic grade of diagenetic, anchizone and epizone in metapelites are reviewed and applied to samples from a 7000?m+ borehole in western China and surface samples from the surrounding Zoigê area. Kübler’s illite crystallinity (IC) measurements provide more consistent results than calculated values of percentage of illite in the I/S mixed layers and percentage of I/S mixed layers. Down-borehole IC values display a typical burial metamorphic relationship between stratigraphic level and IC. A method for preparing very low grade metamorphic maps is described, and isograds plotted on a regional geological map at selected values of IC, delineating a high temperature diagenetic zone, an anchizone, and an epizone. The map shows that IC values are controlled by stratigraphic level in the north of the study area (i.e. burial metamorphism), and proximity to an igneous intrusive body in the south (i.e. contact metamorphism). 相似文献
5.
陈福坤 《中国地球化学学报》2002,21(2):107-119
High-grade metamorphic Variscan basement is exposed in the Moldanubian zone of the Black Forest (BF), being the internal zone of the European Variscan belt. Zircon grains from K-rich felsic orthogneisses and an anatectic paragneiss in the Moldanubian Black Forest demonstrate a multi-stage crystallization at ～ 600 Ma, ～ 480 Ma, ～ 400 - 380 Ma, and ～350 Ma. The last three stages of crystallization probably represent metamorphic overprint during pre-Variscan and Variscan metamorphism.Using stepwise leaching procedures, garnet minerals from felsic orthogneisses as well as paragneisses in the Moldanubian Black Forest yielded Early Carboniferous Sm-Nd ages (～ 330- 340 Ma), which are consistent with the well-constrained Variscan HT metamorphic event,and Early Palaeozoic ( ～480 Ma) to Devonian ( ～400 - 370 Ma) Pb-Pb ages. The coincidence of growth time for zircon and garnet minerals at Early Palaeozoic is interpreted as dating a metamorphic event. These garnet data demonstrate that the Moldanubian BF basement underwent at least two metamorphic events during the Early Palaeozoic and Early Carboniferous.During the Variscan HT metamorphism, the Sm-Nd system of garnet was disturbed, but not the U-Pb system, implying the peak metamorphic temperature was lower than ～800℃. 相似文献
6.
Characteristics of Late-Quaternary Activity and Seismic Risk of the Northeastern Section of the Longmenshan Fault Zone 总被引：1，自引：0，他引：1
Following the 2008 Wenchuan M8 earthquake,the seismic risk of the northeastern section of the Longmenshan fault zone and the adjacent Hanzhong basin has become an issue that receives much concern.It is facing,however,the problem of a lack of sufficient data because of little previous work in these regions.The northeastern section of the Longmenshan fault zone includes three major faults：the Qingchuan fault,Chaba-Lin＇ansi fault,and Liangshan south margin fault,with the Hanzhong basin at the northern end.This paper presents investigations of the geometry,motion nature,and activity ages of these three faults,and reveals that they are strike slip with normal faulting,with latest activity in the Late Pleistocene.It implies that this section of the Longmenshan fault zone has been in an extensional setting,probably associated with the influence of the Hanzhong basin.Through analysis of the tectonic relationship between the Longmenshan fault zone and the Hanzhong basin,this work verifies that the Qingchuan fault played an important role in the evolution of the Hanzhong basin,and further studies the evolution model of this basin.Finally,with consideration of the tectonic setting of the Longmenshan fault zone and the Hanzhong basin as well as seismicity of surrounding areas,this work suggests that this region has no tectonic conditions for great earthquakes and only potential strong events in the future. 相似文献
7.
The paper studies CO2 degassing and controlling factors under the condition of contact metamorphism in the Shuangshan area, southern Tan-Lu fault belt and the method of calculating the amount of CO2 degassing. The results show that the amount of CO2 degassing is controlled by the characteristics of the country rocks, including the thermal conductivity, penetrability, porosity and connectivity. Compositions, size and depth of intrusive rock also have an important influence on CO2 degassing, i.e., they generated numerous cracks in the country rocks, and thus allowed the easy flow and accumulation of fluids. The amount of CO2 flux in contact metamorphism is calculated quantitatively based on the metamorphic reaction and time-integrated fluid flux. The value （0.729- 2.446×10^4 mol/cm^2） of CO2 flux suggests that CO2 was provided mainly by the contact metamorphic reaction. The generation and releasing of CO2 are positively correlated with the degree of metamorphism, and XCO2 in fluids gradually increases from dolomite zone to calcite zone, but in the zone of grossular, fluid flux is the largest and XCO2 sharply decreases due to involvement of magmatic water. This study presents evidence that a large amount of industrial-scale CO2 can be produced during contact metamorphism. On the basis of theoretical and practical studies, a cone model has been proposed to response CO2 degassing for the contact metamorphism, and it can be used to explore CO2 accumulations beyond the oil-gas basins. This model can also be applied to the study of inorganic genesis of CO2 accumulations. 相似文献
8.
Discussed in this paper are the relationship between the compressive fault zone and mineralization, and the regularities governing the concentration-dispersion of elements in the compressive fault zone based on chemically determined data from field and laboratory studies of megascopic structures and tectonite. Horizontal zoning has been recognized in the compressive fault zone, with four distinct zones from the centre outwards. Four groups of chemical components in these four zones are distinguished: the first group --SiO2, FeO, MgO and MnO; the second -- Fe2O3, Na2O and K2O; the third -- CaO and Al2O3 ; and the fourth -- TiO2 and P2O5. Furthermore, various tectono-geochemical processes (including dynamic differentiation or mechanical metamorphic differentiation, dynamically thermal metamorphism,oxidation-reduction, and hydrolysis and dewatering) in the fault zone are also discussed in detail. 相似文献
9.
Burial Metamorphism of the Ordos Basin in Northern Shaanxi 总被引：1，自引：0，他引：1
Zhang Lifei 《《地质学报》英文版》1993,67(2):181-193
Burial metamorphism has been found in the Ordos basin of northern Shaanxi. On the basis of a rather intensive study of burial metamorphism of sandstone, it has been shown that the evolution from diagenesis to metamorphism involves four stages: cementation of clay minerals, regrowth of pressolved quartz and feldspar, cementation of carbonates and formation of laumontite. On that basis it has been put forward that the laumontite is formed by burial metamorphism of clay and carbonate minerals. According to the thermodynamic data of minerals, the conditions under which laumontite is formed are T<250℃ and X_(CO_2)<0.17. High-resolution SEM and TEM studies of clay minerals in mudstone show that there occur a mixed layer assemblage of bertherine and illite/chlorite and transformation from bertherine to chlorite. On that basis coupled by the X-ray diffraction analysis the author suggests the following transformation of clay minerals during burial metamorphism: the earliest smectite-kaolinite assemblage changes into the bertherine-illite mixture with increasing depth, then into the illite/chlorite mixed layer assemblage and finally into dispersed individual illite and chlorite. The reaction of the transformation is:smectite+kaolinite+K~+=illite+chlorite+quartz According to the study of the oxygen isotope thermometry of the coexisting illitequartz pair, the temperature of the above transformation is lower than 180℃. 相似文献
10.
Soumyajit MUKHERJEE 《《地质学报》英文版》2014,88(6):1729-1741
Abstract: Biotite and muscovite inclusions inside mica host minerals from the Sutlej section of the Higher Himalayan Crystalline were studied under an optical microscope. These inclusions formed possibly by local recrystallization of mica grains during regional prograde metamorphism, with some affected by top-to-SW shear leading to parallelogram shapes. Recrystallization may have been assisted by solution transfer along the cleavage planes of the host grains. The relative competency of deformed phyllosilicate inclusions with the same or different composition to the host depends on the size and orientation of (001) cleavage planes of the inclusions relative to the host. Shearing of mica inclusions led to their parallelogram geometries within the contained mica inclusions. Some of the sheared inclusions deflect cleavage planes in the host minerals and define flanking microstructures. Trapezoid-shaped inclusions are a new finding that deserves more attention for their genesis. These structurally anisotropic inclusions did not originate from sub-grains, secondary infillings or retrogression. These inclusions are also not related to pseudomorphism, isomorphism, folding of the bulk rock etc. Some of the inclusions formed by recrystallization of the host mineral during top-to-SW ductile shear. 相似文献
11.
S. Viswanathan K. Surya Prakash Rao B. Mahabaleswar 《Journal of the Geological Society of India》2013,82(6):621-627
Komatiites are mantle-derived ultramafic volcanic rocks. Komatiites have been discovered in several States of India, notably in Karnataka. Studies on the distribution of trace-elements in the komatiites of India are very few. This paper proposes a simple, accurate, precise, rapid, and non-destructive wavelength-dispersive x-ray fluorescence (WDXRF) spectrometric technique for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in komatiites, and discusses the accuracy, precision, limits of detection, x-ray spectral-line interferences, inter-element effects, speed, advantages, and limitations of the technique. The accuracy of the technique is excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Zr, Nb, Ba, Pb, and Th and very good (within 4%) for Y. The precision is also excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th. The limits of detection are: 1 ppm for Sc and V; 2 ppm for Cr, Co, and Ni; 3 ppm for Cu, Zn, Rb, and Sr; 4 ppm for Y and Zr; 6 ppm for Nb; 10 ppm for Ba; 13 ppm for Pb; and 14 ppm for Th. The time taken for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in a batch of 24 samples of komatiites, for a replication of four analyses per sample, by one operator, using a manual WDXRF spectrometer, is only 60 hours. 相似文献
12.
奥地利安东帕有限公司 《岩矿测试》2009,28(3):306-306
最新的流行病学研究表明,空气中较高浓度的悬浮细颗粒可能对人类的健康有不利的影响。根据该项研究显示,由于心脏病、慢性呼吸问题和肺功能指标恶化而导致死亡率的升高与细尘粒子有关。这些研究结果已经促使欧盟于1999年4月出台了限制空气中二氧化硫、二氧化氮、氧化氮、铅和颗粒物含量的法案(1999/30/EC),对各项指标包括对可吸入PM10颗粒的浓度提出了新的限制性指标。PM10颗粒是指可以通过预分级器分离采集的气体动力学直径小于10μm的细颗粒。目前研究的兴趣重点逐步偏向PM2.5这些更细微颗粒物,PM2.5这种颗粒物对健康有明显的不利影响。在欧盟指令2008/50/EC中,对PM10和PM2.5都提 相似文献
13.
E. M. Prasolov S. A. Sergeev B. V. Belyatsky E. S. Bogomolov K. A. Gruzdov I. N. Kapitonov R. Sh. Krymsky V. O. Khalenev 《Geochemistry International》2018,56(1):46-64
This paper reports the first results of a study of 11 isotope systems (3He/4He, 40Ar/36Ar, 34S/32S, 65Cu/63Cu, 62Ni/60Ni, 87Sr/86Sr, 143Nd/144Nd, 206–208Pb/204Pb, Hf–Nd, U–Pb, and Re–Os) in the rocks and ores of the Cu–Ni–PGE deposits of the Norilsk ore district. Almost all the results were obtained at the Center of Isotopic Research of the Karpinskii All-Russia Research Institute of Geology. The use of a number of independent genetic isotopic signatures and comprehensive isotopic knowledge provided a methodic basis for the interpretation of approximately 5000 isotopic analyses of various elements. The presence of materials from two sources, crust and mantle, was detected in the composition of the rocks and ores. The contribution of the crustal source is especially significant in the paleofluids (gas–liquid microinclusions) of the ore-forming medium. Crustal solutions were probably a transport medium during ore formation. Air argon is dominant in the ores, which indicates a connection between the paleofluids and the atmosphere. This suggests intense groundwater circulation during the crystallization of ore minerals. The age of the rocks and ores of the Norilsk deposits was determined. The stage of orebody formation is restricted to a narrow age interval of 250 ± 10 Ma. An isotopic criterion was proposed for the ore-bearing potential of mafic intrusions in the Norilsk–Taimyr region. It includes several interrelated isotopic ratios of various elements: He, Ar, S, and others. 相似文献
14.
15.
16.
Mining induced subsidence can significantly affect mining costs where major surface facilities and natural environment need to be protected. Overburden grout injection is a technology used to control coal mine subsidence by injecting the mine waste material extracted from the coal back into the inter-burden rock during longwall mining. The flowing slurry is here categorised as a nonlinear viscous cohesive (Bingham plastic) fluid. During longwall mining the grout slurry is pumped into the separated beds of the rock mass through a central vertical borehole, which is drilled deep into the inter-burden rock strata above the coal seam. However, a blockage can occur in the injection system when the slurry velocity falls below a certain critical threshold velocity, indicating a material phase change from cohesive-viscous to cohesive-frictional. In situ field injection tests through boreholes have been simulated at a smaller scale at the CSIRO laboratory in Brisbane by pumping the slurry through a radial disk (gap = 4 mm) from its centre. Laboratory experiments indicate a general, nonlinear, cohesive, viscous, frictional model for shear behaviour of the slurry, in which the material shear parameters are functions of the disk radial distance. Complete dimensional and dimensionless analytical solutions have been developed based on an approach related to Bingham–Herschel–Bulkley fluid mechanics. The derived formulae include relations for minimum pump pressure, local pressure and pressure gradient, wall shear stress, volume rate, velocity and velocity gradient. The theoretical results match the experimental measurements. The experiments covered slurries with maximum particle sizes of 0.5 to 2 mm with about 50% being larger than 100 µm. The viscosities at the various solids concentrations were measured with a standard torsion viscometer. This study differs from the previous research in several distinct aspects, namely, consideration of the variable shear parameters rather than fixed values, inclusion of total nonlinear behaviour, and implementation of a friction function to mimic behaviour of the deposited and consolidating stiff slurry, which can cause a significant pressure rise as a result of the increased shear resistance. 相似文献
17.
18.
Between 1985 and 1991, two new mountain protected areas (MTNPA) covering more than 35,000 km2 and based on participatory management models — the Makalu-Barun National Park and Conservation Area, Nepal, and Qomolangma Nature Preserve, Tibet Autonomous Region — were successfully established through the collaborative efforts of Woodlands Mountain Institute and conservationists in China and Nepal. Characteristics common to both projects include the importance of establishing (1) effective rationales, (2) local support constituencies, (3) a senior advisory group, (4) a task force, (5) linkages between conservation and development, and (6) fund raising mechanisms. The lessons derived from the experiences of Woodlands Mountain Institute are of significant value to others in preserving MTNPA. Increased collaboration and communication between all interested in conservation, however, will remain a critical component for expanding mountain protected area coverage to throughout the world. 相似文献
19.
《Applied Geochemistry》2001,16(2):137-159
Five hundred and ninety-eight samples of terrestrial moss (Hylocomium splendens and Pleurozium schreberi) collected from a 188,000 km2 area of the central Barents region (NE Norway, N Finland, NW Russia) were analysed by ICP-AES and ICP-MS. Analytical results for Al, B, Ba, Ca, K, La, Mg, Mn, Na, P, Rb, Si, Sr, Th, U and Y concentrations are reported here. Graphical methods of data analysis, such as geochemical maps, cumulative frequency diagrams, boxplots and scatterplots, are used to interpret the origin of the patterns for these elements. None of the elements reported here are emitted in significant amounts from the smelting industry on the Kola Peninsula. Despite the conventional view that moss chemistry reflects atmospheric element input, the nature of the underlying mineral substrate (regolith or bedrock) is found to have a considerable influence on moss composition for several elements. This influence of the chemistry of the mineral substrate can take place in a variety of ways. (1) It can be completely natural, reflecting the ability of higher plants to take up elements from deep soil horizons and shed them with litterfall onto the surface. (2) It can result from naturally increased soil dust input where vegetation is scarce due to harsh climatic conditions for instance. Alternatively, substrate influence can be enhanced by human activity, such as open-cast mining, creation of ‘technogenic deserts’, or handling, transport and storage of ore and ore products, all of which magnify the natural elemental flux from bedrock to ground vegetation. Seaspray is another natural process affecting moss composition in the area (Mg, Na), and this is most visible in the Norwegian part of the study area. Presence or absence of some plant species, e.g., lichens, seems to influence moss chemistry. This is shown by the low concentrations of B or K in moss on the Finnish and Norwegian side of the (fenced) border with Russia, contrasting with high concentrations on the other side (intensive reindeer husbandry west of the border has selectively depleted the lichen population). 相似文献
20.
Marta L. PATINO-DOUCE Alberto PATINO-DOUCE Mazhar QAYYUM Roger L. NIELSEN 《Geostandards and Geoanalytical Research》1994,18(2):195-198
We have developed a set of four synthetic standards for the rare earth and high field strength elements designed for use in the determination of those elements in silicates. The base material is a glass nominally at the eutectic of the MgO-Al2 O3 -SiO2 ternary system. The nominal doping level was 2 wt% of the elements as oxides. To avoid problems associated with peak interference, the elements were doped in four separate glasses. 相似文献