共查询到20条相似文献，搜索用时 78 毫秒
1.
多目标地球化学填图是多目标区域地球化学调查中重要的区域性基础性工作之一,为了更好地反映出地球化学背景变化,要求分析方法具有更高的准确度、精密度以及更低的检出限。地球化学调查样品中的硼锗溴钼锡碘钨主要采用单独或分组熔矿的方法进行制备和测定,操作流程长且涉及6种测定方法。本文基于前人研究,对以上7种元素的分析方法进行系统总结,采用过氧化钠-氢氧化钠碱熔,分取溶液加入柠檬酸,利用阳离子交换树脂,静态交换2～3h,除去溶液中大量的阳离子减少基体干扰,利用电感耦合等离子体质谱法(ICP-MS)测定硼锗溴钼锡碘钨含量。结果表明：7种元素的检出限分别为0.66、0.096、0.78、0.11、0.15、0.29、0.27μg/g,相对标准偏差(RSD,n=11)在2.1%～7.5%之间,均小于10%。该方法操作简便、快速,应用成本低,并且整合了相关6种分析配套方法,应用于测定厚覆盖区地球化学调查样品,精密度和准确度均满足《多目标区域地球化学调查规范(1∶250000)》(DZ/T 0258—2014)要求。 相似文献
2.
银硼锡元素的丰度和变化特征可以反映区域成矿条件,指示矿床或矿化存在。碳酸盐矿物中的银硼锡是勘查地球化学及多目标地球化学中的必测元素,其测定方法是地球化学元素配套分析方案中必不可少的方法之一。由于碳酸盐矿物与普通的岩石、土壤和水系沉积物不同,该类矿物主要是灰岩、白云岩等含钙和镁元素比较高的岩石类样品,同时测定样品中银硼锡的技术难点在于高含量钙镁基体会严重干扰低含量待测元素,且摄谱过程中由于易产生二氧化碳造成样品飞溅。针对碳酸盐矿物的特殊性,本文建立了交流电弧-光电直读发射光谱同时测定碳酸盐矿物中银硼锡的分析方法。通过优化样品前处理及实验条件,用10%的盐酸处理样品,消除了基体元素钙和镁的干扰;以锗(Ge)作为内标元素进行定量,可以消除因电弧激发条件变化以及试样基体组分等外部因素造成干扰的影响;采用银与长波锗元素组成分析线对,硼和锡与短波锗元素组成分析线对,灵敏度较好;选择天然碳酸盐岩石与人工合成灰岩等12种国家一级地球化学标准物质作为标准系列,使基体组分与样品相类似;采用分析线和内标线同时扣背景的离线差减法进行背景校正。结果表明:该方法对银硼锡的检出限分别为0.008、0.49、0.18μg/g;方法精密度(RSD)对银大于10%,其余均优于10%;经国家一级地球化学标准物质验证,银硼锡测定平均值与认定值的对数差值(ΔlgC)均小于或等于±0.05,满足多目标区域地球化学调查规范的要求。 相似文献
3.
发射光谱法同时测定地球化学样品中微量银铍硼锡铋钼 总被引：8，自引：2，他引：6
采用垂直电极装样,二米平面光栅交流电弧摄谱测定地质样品中的微量元素银、铍、硼、锡、铋、钼,以三氧化二铝、焦硫酸钾、氟化钠、碳粉和硫粉作缓冲剂,锑、锗作内标。方法检出限为:银0.019μg/g、铍0.11μg/g、硼0.85μg/g、锡0.26μg/g、铋0.031μg/g、钼0.12μg/g。各元素12次测定的相对标准偏差(RSD)均小于10%。用水系沉积物、土壤、岩石国家一级标准物质进行验证,测定值与标准值基本一致,符合多目标地球化学填图的质量要求。 相似文献
4.
树脂交换分离-电感耦合等离子体质谱法测定铅锌矿中钨钼锡锗硒碲 总被引：3，自引：3，他引：0
铅锌矿常与硫化矿共生形成复合多金属矿床,其中伴生有益元素的含量对矿床的综合利用评估有重要的参考意义。在目前常用方法中,钨钼锡锗硒碲主要采用分组或单独熔矿和测试的方法,操作强度大、分析效率低,且高含量铜、铅和含量高于1μg/g的硒分别干扰钨钼和碲的测定。本文采用过氧化钠碱熔,提取后加入0. 8%柠檬酸溶液络合钨、钼、锡形成金属复合物,以8～9 g阳离子树脂交换分离高含量钠盐和铜、铅、锌、铁等主量元素,采用动能歧视模式以铼、硼为内标用电感耦合等离子体质谱仪同时测定钨钼锡锗硒碲的含量。经树脂处理后,铜铅锌铁的去除率均高于96%,在测定介质中实际浓度为0. 192 ng/mL～1. 28μg/mL,基本消除了主量元素的干扰。各待测元素工作曲线相关系数为0. 9994～0. 9999,优于阳离子树脂处理前的0. 9923～0. 9992。经标准物质验证,各元素测定相对误差为-8. 33%～7. 00%,加标回收率为94. 9%～107. 5%,相对标准偏差(RSD,n=8)小于8%。该方法在样品前处理环节将主量干扰元素从溶液体系中分离,优化了测定介质,实现了铅锌矿中多元素的准确快速测定。 相似文献
5.
在对比已有相关分析方法的基础上,建立了粉末压片-波长色散X射线荧光光谱法测定地球化学样品中氯元素的分析方法.采用岩石、沉积物和土壤等78种国家一级地球化学标准物质作为校准系列建立校准曲线;利用经验系数法进行基体效应校正,利用含量校正法进行谱线重叠干扰校正;总结了地球化学样品中氯元素测定值随测定次数的变化规律及原因.结果表明:氯的检出限为7.95μg/g;分析3种国家一级地球化学标准物质12次,得到测定值的相对标准偏差均小于10％;采用国家一级地球化学标准物质验证方法准确度,测定值与标准物质认定值相吻合,测定平均值与标准物质认定值的对数差值的绝对值(?lgω)均小于或等于0.02,满足多目标区域地球化学调查规范的要求. 相似文献
6.
掌握地质样品中银锡硼钼铅的含量对于研究成矿规律和地球化学找矿极其重要,目前的分析方法很少能一次性准确高效检出银锡硼钼铅。本文在前人研究基础上建立了应用全谱发射光谱仪固体粉末进样,一次性高效、准确地分析检测地质样品中银锡硼钼铅的方法。采用国家一级标准物质(岩石、土壤和水系沉积物)对合成硅酸盐标准曲线进行第二次拟合以降低基体的干扰;设置元素分析谱线转换值实现元素分析谱线的简单切换,不同的样品含量使用不同的分析谱线,达到分析结果更加接近样品真值的效果,同时扩大了标准曲线线性范围。结果表明:银锡硼钼铅的检出限分别为0.0077μg/g、0.19μg/g、0.68μg/g、0.058μg/g、0.49μg/g,方法精密度在3.23%～9.39%之间。应用本方法分析土壤、水系沉积物、岩石国家一级标准物质的测定值与其认定值相符,△logC值的绝对值均小于0.10;实际样品和外控样的一次测试结果合格率分别为92%～98%、100%。本方法简单,分析速度快,避免了样品稀释带来的污染,使用多条分析谱线测定国家标准物质,相比传统发射光谱法使用单分析谱线的测定值更加接近认定值,检出限优于《地质矿产实验室测试质量管理规范》的规定值。 相似文献
7.
电感耦合等离子体光谱／质谱法测定环境样品中的硼 总被引：7，自引：3，他引：7
采用HF-HNO3-H3PO4-HClO4密封溶样处理样品,电感耦合等离子体光谱/质谱法(ICP-AES/MS)测定农作物、膳食和粪便中的硼。所拟定的方法在测硼的同时,还可测定Cr、Cu、Li、V、Co、Zn、Sr、Cd、Ba、K、Na、Fe、Mn、Zn元素,可以为农作物和饮食中痕量元素研究提供参考。ICP-AES测定硼的方法检出限(3σ)为0.0063μg/mL,测定限(10σ,DF=100)为2.10μg/g;ICP-MS测定硼方法检出限(3σ)为0.0228ng/mL,测定限(10σ,DF=1000)为0.092μg/g。方法经植物国家一级标准物质GBW07602～07605验证,测定值与标准值接近,样品10次测定的RSD<10%。 相似文献
8.
电感耦合等离子体质谱法测定铅合金中的微量杂质元素镉和锡 总被引：1，自引：1，他引：0
铅合金中的镉和锡由于含量较低,国家标准方法均为单一元素分析,步骤繁琐,检出限高,难以达到理想的检出要求。本文建立了应用电感耦合等离子体质谱法(ICP-MS)测定铅合金中微量级(μg/g级)杂质元素镉和锡的分析方法。采用单一的低浓度硝酸溶解铅合金,用低温慢溶的方式使样品溶解更加完全,减少了多离子对仪器的干扰;通过铅基体匹配和加入酒石酸保证了标准与样品介质的一致性,同时避免了锡的水解;以~(103)Rh作为内标元素,~(111)Cd和~(118)Sn作为测量同位素克服了质谱干扰。方法检出限为镉0.05 ng/g、锡0.04 ng/g,比国家标准方法的检出限(1~6μg/g)低,精密度小于4%。该方法试剂用量少,减少了处理样品的复杂性,实现了合金中微量级元素的准确测定。 相似文献
9.
电感耦合等离子体质谱法同时测定地质样品中锗碘 总被引：2，自引：8，他引：2
样品用NaOH全熔,热水提取,分取部分溶液通过强酸性阳离子交换树脂,分离溶液中大量的钠离子后,采用电感耦合等离子体质谱法同时测定锗和碘。方法的检出限Ge、I分别为0.043μg/g和0.22μg/g,经土壤国家一级标准物质分析验证,结果与标准值相符,12次测定的RSD均小于10%。 相似文献
10.
利用离子选择电极测定岩盐样品中的氯和碘离子的含量,测定氯离子时以KNO_3和柠檬酸三钠为离子强度调节剂,测定碘离子时以硝酸钾、柠檬酸和柠檬酸三钠为离子强度调节剂,Na_2SO_3为还原保护剂,再双盐桥饱和甘汞电极外盐桥填充均为0.1mo L/L的KNO_3溶液。结果表明碘和氯离子线性良好,氯离子检测下限为0.0116μg/g,有良好的样品回收率(98.1%～102.2%);碘离子检测下限为0.0030μg/g,有良好的样品回收率(97.6%～102.5%)。该方法操作过程简单、分析速度快,造价成本低,灵敏度高,同时改善了实验室用ICP-MS测定碘元素背景干扰严重和硝酸汞滴定法测定低含量氯元素难以准确检测的问题,在实际应用中得到有效的验证。 相似文献
11.
S. Viswanathan K. Surya Prakash Rao B. Mahabaleswar 《Journal of the Geological Society of India》2013,82(6):621-627
Komatiites are mantle-derived ultramafic volcanic rocks. Komatiites have been discovered in several States of India, notably in Karnataka. Studies on the distribution of trace-elements in the komatiites of India are very few. This paper proposes a simple, accurate, precise, rapid, and non-destructive wavelength-dispersive x-ray fluorescence (WDXRF) spectrometric technique for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in komatiites, and discusses the accuracy, precision, limits of detection, x-ray spectral-line interferences, inter-element effects, speed, advantages, and limitations of the technique. The accuracy of the technique is excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Zr, Nb, Ba, Pb, and Th and very good (within 4%) for Y. The precision is also excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th. The limits of detection are: 1 ppm for Sc and V; 2 ppm for Cr, Co, and Ni; 3 ppm for Cu, Zn, Rb, and Sr; 4 ppm for Y and Zr; 6 ppm for Nb; 10 ppm for Ba; 13 ppm for Pb; and 14 ppm for Th. The time taken for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in a batch of 24 samples of komatiites, for a replication of four analyses per sample, by one operator, using a manual WDXRF spectrometer, is only 60 hours. 相似文献
12.
13.
奥地利安东帕有限公司 《岩矿测试》2009,28(3):306-306
最新的流行病学研究表明,空气中较高浓度的悬浮细颗粒可能对人类的健康有不利的影响。根据该项研究显示,由于心脏病、慢性呼吸问题和肺功能指标恶化而导致死亡率的升高与细尘粒子有关。这些研究结果已经促使欧盟于1999年4月出台了限制空气中二氧化硫、二氧化氮、氧化氮、铅和颗粒物含量的法案(1999/30/EC),对各项指标包括对可吸入PM10颗粒的浓度提出了新的限制性指标。PM10颗粒是指可以通过预分级器分离采集的气体动力学直径小于10μm的细颗粒。目前研究的兴趣重点逐步偏向PM2.5这些更细微颗粒物,PM2.5这种颗粒物对健康有明显的不利影响。在欧盟指令2008/50/EC中,对PM10和PM2.5都提 相似文献
14.
E. M. Prasolov S. A. Sergeev B. V. Belyatsky E. S. Bogomolov K. A. Gruzdov I. N. Kapitonov R. Sh. Krymsky V. O. Khalenev 《Geochemistry International》2018,56(1):46-64
This paper reports the first results of a study of 11 isotope systems (3He/4He, 40Ar/36Ar, 34S/32S, 65Cu/63Cu, 62Ni/60Ni, 87Sr/86Sr, 143Nd/144Nd, 206–208Pb/204Pb, Hf–Nd, U–Pb, and Re–Os) in the rocks and ores of the Cu–Ni–PGE deposits of the Norilsk ore district. Almost all the results were obtained at the Center of Isotopic Research of the Karpinskii All-Russia Research Institute of Geology. The use of a number of independent genetic isotopic signatures and comprehensive isotopic knowledge provided a methodic basis for the interpretation of approximately 5000 isotopic analyses of various elements. The presence of materials from two sources, crust and mantle, was detected in the composition of the rocks and ores. The contribution of the crustal source is especially significant in the paleofluids (gas–liquid microinclusions) of the ore-forming medium. Crustal solutions were probably a transport medium during ore formation. Air argon is dominant in the ores, which indicates a connection between the paleofluids and the atmosphere. This suggests intense groundwater circulation during the crystallization of ore minerals. The age of the rocks and ores of the Norilsk deposits was determined. The stage of orebody formation is restricted to a narrow age interval of 250 ± 10 Ma. An isotopic criterion was proposed for the ore-bearing potential of mafic intrusions in the Norilsk–Taimyr region. It includes several interrelated isotopic ratios of various elements: He, Ar, S, and others. 相似文献
15.
Mining induced subsidence can significantly affect mining costs where major surface facilities and natural environment need to be protected. Overburden grout injection is a technology used to control coal mine subsidence by injecting the mine waste material extracted from the coal back into the inter-burden rock during longwall mining. The flowing slurry is here categorised as a nonlinear viscous cohesive (Bingham plastic) fluid. During longwall mining the grout slurry is pumped into the separated beds of the rock mass through a central vertical borehole, which is drilled deep into the inter-burden rock strata above the coal seam. However, a blockage can occur in the injection system when the slurry velocity falls below a certain critical threshold velocity, indicating a material phase change from cohesive-viscous to cohesive-frictional. In situ field injection tests through boreholes have been simulated at a smaller scale at the CSIRO laboratory in Brisbane by pumping the slurry through a radial disk (gap = 4 mm) from its centre. Laboratory experiments indicate a general, nonlinear, cohesive, viscous, frictional model for shear behaviour of the slurry, in which the material shear parameters are functions of the disk radial distance. Complete dimensional and dimensionless analytical solutions have been developed based on an approach related to Bingham–Herschel–Bulkley fluid mechanics. The derived formulae include relations for minimum pump pressure, local pressure and pressure gradient, wall shear stress, volume rate, velocity and velocity gradient. The theoretical results match the experimental measurements. The experiments covered slurries with maximum particle sizes of 0.5 to 2 mm with about 50% being larger than 100 µm. The viscosities at the various solids concentrations were measured with a standard torsion viscometer. This study differs from the previous research in several distinct aspects, namely, consideration of the variable shear parameters rather than fixed values, inclusion of total nonlinear behaviour, and implementation of a friction function to mimic behaviour of the deposited and consolidating stiff slurry, which can cause a significant pressure rise as a result of the increased shear resistance. 相似文献
16.
17.
Alexander E. C. Broberg J. S. Kehren A. R. Graziani M. M. Turri W. L. 《Environmental Geology》1993,22(4):353-361
Bellechester, Minnesota, is a small community of approximately 155 residents located on the county line between Goodhue and Wabasha counties in southeast Minnesota's karst region. Bellechester is served by a 21-year-old wastewater treatment facility (WWTF) consisting of three waste-stabilization ponds. On 28 April 1992 six sinkholes were discovered to have drained cell 2 of the WWTF resulting in the loss of approximately 8.7×106 1 of partially treated effluent and about 600 m3 of soil into previously undetected subsurface voids of unknown dimensions. In the week following the collapse, approximately 200 water wells located within a 5-km radius of the WWTF were sampled in an after-the-fact, emergency sampling program. Twelve samples with elevated fecal coliform levels, 18 samples with nitrate-nitrogen greater than the 10 mg/1 standard, and no samples with elevated chlorides were found. However, the elevated levels could not be unambiguously attributed to the WWTF collapse. This is the third WWTF to fail by sinkhole collapse in southeast Minnesota since 1974. All three collapsed lagoons have been located in similar geomorphic and stratigraphic settings. However, at least two lagoons have collapsed in the adjacent area in northeast Iowa, and these lagoons are located at different stratigraphic positions. Twenty-two WWTFs constructed in southeast Minnesota's karst region in the last 25 years have been identified as subject to potential sinkhole collapse. An unknown but significant number of manure storage lagoons, flood control structures, etc., have also been constructed in the karst region and are at risk. Public agencies are beginning to develop plans to deal with the risk associated with existing and future waste lagoons in this environment. The critical hydrogeologic parameters that can be used to prioritize the risk of collapse at existing facilities include: (1) the lithology of the first bedrock beneath each lagoon, (2) the thickness of surficial materials between the lagoon and the bedrock surface, (3) the presence and construction of liners (seepage rate), and (4) the proximity to existing sinkholes. 相似文献
18.
Mercury,arsenic, antimony,and selenium contents of sediment from the Kuskokwim River,Bethel, Alaska,USA 总被引：1，自引：0，他引：1
The Kuskokwim River at Bethel, Alaska, drains a major mercury-antimony metallogenic province in its upper reaches and tributaries. Bethel (population 4000) is situated on the Kuskokwim floodplain and also draws its water supply from wells located in river-deposited sediment. A boring through overbank and floodplain sediment has provided material to establish a baseline datum for sediment-hosted heavy metals. Mercury (total), arsenic, antimony, and selenium contents were determined; aluminum was also determined and used as normalizing factor. The contents of the heavy metals were relatively constant with depth and do not reflect any potential enrichment from upstream contaminant sources. 相似文献
19.
滇东南锡、银、铅、锌多金属矿床主要分布在个旧、白牛厂、都龙3个矿区,而滇东南较大的3个花岗岩体又分别出露在3个矿区或附近.花岗岩体均形成于燕山晚期,岩石化学、矿物成分相似,富含锡、银、铅、锌、钨、铜等成矿元素.矿床主金属元素组合与岩体之间的距离由远而近出现由锡、钨、(铍、铌、钽)→锡、钨、(铁)、铜、铟→锡、铅、锌、银、铟、(锑)有规律的变化.花岗岩浆是成矿物质来源和成矿热源.岩浆侵入初期使上覆地层隆起产生背斜(凹陷部位成向斜);同时使地层产生一系列裂隙、压性断层或层间断裂;岩浆侵入晚期,这些断层再次活动,表现为张性,岩浆产生的含矿热液沿由其活动所造成的断裂迁移、充填、交代、沉淀而形成矿床. 相似文献
20.
岩石密度和超高压岩石折返速率 总被引：1，自引：3，他引：1
在常温常压条件下对中国大陆科学钻CCSD主孔100-3000米岩心样品进行了密度测量,建立了密度连续剖面,并界定了不同超高压岩石的密度值。通过对比高温高压物性实验资料,岩石密度随着退变程度增强而降低,榴辉岩密度变化序列为3.52g/cm3→3.49g/cm3→3.07g/cm3→2.93g/cm3。超高压长英质岩石密度变化序列为3.00g/cm→2.80g/cm3→2.65g/cm3。上述实验资料是讨论不同折返阶段岩石所受浮力的基础,为研究折返速率大小提供了基本参数。本文通过折返板块运动平衡时,上浮力与粘滞力平衡这一关系式,定量研究了大陆俯冲板块的折返速率,认为密度差产生上浮力从而引起折返,温度对板块折返速率的影响最为显著;密度差大小、折返角度、折返板块大小对折返速率也有直接的影响。定量模拟分析表明,在温度高于850℃时,板块的折返速率可以超过100mm/a;当温度降至700℃时,折返速率则低于1.5mm/a。作者认为在折返早期,温度较高,板块快速折返至60-70km榴辉岩相深度;随着传导散热,温度降低,板块以较慢的速率折返至中下地壳。折返速率的估算表明,浮力是板块折返第一阶段(从>100km深部折返至<40km的中下地壳)的主要驱动力。 相似文献