共查询到20条相似文献，搜索用时 820 毫秒
1.
利用国际刻度参考装置AlphaGUARD测氡仪及水氡测量组件, 使用水中溶解氡(或豁免级氡气源), 开展代替目前氡气固体源校准方法实验。 对FD-125测氡仪标配的3个闪烁室(1#、 3#及5#)分别使用水中溶解氡和氡气固体源进行校准实验, 3个闪烁室的校准K值相对误差分别为5.06%, 1.92%及2.76%, 可以达到目前地震监测氡观测技术要求。 实验结果表明, 水中溶解氡代替氡气固体源校准, 可以解决目前氡气固体源校准中存在的运输困难、 维修技术要求高等问题, 是今后氡观测仪器校准技术的发展趋势。 相似文献
2.
With increasing demands on limited water resources, regulation of larger river systems continues to increase and so too does the need for accurate water accounting and prediction in these systems. River system models are either calibrated manually or automatically on a reach‐by‐reach basis, i.e. each reach is calibrated as a separate entity with little or no consideration of fluxes at other locations within the river system. While this is a practical approach, simulation errors can propagate downstream to make calibration or prediction difficult at those locations. Likewise parameters may suffer from over‐fitting especially where observations are erroneous. We developed and implemented a system calibration strategy in a portion of the Murrumbidgee River, Australia, where parameters for 11 gauges (36 parameters) were calibrated together. Parameter values, model states and model goodness of fit were compared to reach‐by‐reach calibration. The system calibration produced a better goodness of fit across the whole system relative to reach‐by‐reach calibration. Additionally, model system states were more realistic than reach‐by‐reach optimized models. Over‐fitting was obvious using the reach‐by‐reach method for one reach/gauge in particular. This was avoided with system calibration method, with improved goodness of fit at all gauges downstream of the problem gauge. The results here suggest that the system calibration approach provides more hydrologically consistent states, improved overall fit and avoids over‐fitting at problem gauges. Copyright © 2015 John Wiley & Sons, Ltd. 相似文献
3.
为保证气氡测量结果准确性和可靠性,需对测氡仪器进行定期校准。应用目前我国地震系统内常用的三种校准方法：标准仪器校准法、RN-FD循环式氡气源校准法及固体氡气源校准法,对入网新型气氡仪进行校准方法比测。得出结果认为：循环式常压取源方式更接近新型数字化氡观测仪器的正常工作方式;标准仪器校准法是目前正在使用的几种校准方法中系统误差最小、校准效率最高、维护成本最低的方法;RN-FD循环式氡气源校准法和固体氡气源校准法均为标准物质传递方法,该方法存在诸多困难及不便(如放射性固体源运输、人员技术及环保监管等)影响仪器校准的及时性。通过分析这三种校准方法在原理、使用操作方法等方面的差异,讨论它们对校准结果准确度的影响,为新型仪器的校准操作规程(规范)的编写及实施提供参考。 相似文献
4.
离心模型试验常用微型土压力传感器测量地基或土与结构接触边界上的土压力。传感器使用之前应进行标定。传统的液标或气标方法不能准确反映传感器埋置过程对土体的扰动或传感器周围人为土拱边界条件形成,导致测试结果不甚理想。故针对试验条件,设计制作一套标定微型土压力传感器的方法和装置,以水、粉质黏土和福建标准砂为标定介质,考虑有无刚性靠背两种工作状态对多个传感器进行室内标定,得到标定系数。结果表明:水标未出现卸载滞后,砂标和土标均出现卸载滞后,且表现为非线性;引入滞后比R评价微型土压力传感器的滞后性,认为标定介质和传感器类型是影响滞后比的两个主要因素;传感器自身材料特性和几何特性、地基土的制备和传感器放置、加载预压和加卸载循环等对土体密实度、土体强度等的改变、工作介质和状态等对标定结果有影响。建议尽量模拟试验工作介质和工作状态,逐个标定传感器,以得到更准确的土压力测量值。 相似文献
5.
根据氡观测仪的氡室校准和氡气固体源校准两种校准方式的实验结果, 讨论了使用标准仪器校准氡观测仪器的可靠性问题。 用国际公认的计量传递仪器AlphaGUARD P2000Pro或AlphaGUARD P2000F测氡仪作为氡气溯源仪器, 对九江地震台FD-125氡钍分析器的三个闪烁室进行了氡室校准、 氡气固体源校准和仪器校准三种方法实验, 得到标准仪器校准、 氡气固体源校准得出K值相对氡室校准结果偏差均小于6%, 结果表明, 三种方法的校准结果均符合目前氡观测计量溯源技术要求, 能达到与国家氡计量刻度相统一目的。 相似文献
6.
对测氡仪器进行定期校准是保证测量结果准确性和可靠性的关键。基于用国际公认的计量传递仪器AlphaGUARD P2000F作为氡气溯源仪器及其自带水氡测量组件对三套DDL-1型电离法测氡仪使用水中溶解氡进行校准实验。实验结果和用固体氡源校准三套仪器的结果与仪器出厂校准结果进行对比,两种校准方法的K值相对误差均小于5%,达到目前地震监测氡观测技术要求。实验结果表明,水中溶解氡代替固体氡气源校准,可以解决目前固体氡源校准中存在的运输困难、维修技术要求高、国家环保部门监管严格等问题,为地震氡观测仪器校准技术找到了一种新的途径。 相似文献
7.
为了能够精确地测量海底表层沉积物的声学参数,自主研制了一种新型海底沉积物声学原位测量系统,与国内外传统的声学原位测量系统相比,该系统能够实时显示声波波形,调整测量参数,其工作方式除了站位式测量之外,还实现了拖行式连续测量,极大地提高了工作效率.根据前期海试情况,对海底仪器结构进行了重新设计,使之可以同时测量海底沉积物及海底海水的声学参数,同时建立了双向数字信道,解决了测量过程中系统信号的干扰问题.该系统的结构分为两部分:甲板控制单元和水下测量单元,整套系统通过主机控制程序进行控制,采用GPS定位系统测定仪器的大地坐标.为了检验系统的稳定性及准确性,分别进行了实验室水槽实验和海上试验.利用水声测量设备对测量系统进行实验室水槽标定分析,实验结果表明系统测量值相对误差仅为0.04%,测量结果具有较高的精度.海上试验在青岛胶州湾和东海海域进行,获得了试验区域海底沉积物声速和声衰减系数的测量数据,将测量数据与他人的研究结果进行对比分析,结果表明测量数据与前人研究结果一致,较为准确.该原位测量系统在站位式测量和拖行式测量中都能够快速准确地测量出沉积物声速和声衰减系数,可以作为海底底质声学测量的调查设备. 相似文献
8.
Research on geo-electrical resistivity observation system specially used for earthquake monitoring in China 
下载免费PDF全文
下载免费PDF全文 This paper deals with the design and development of the observational system of geo-electrical resistivity on the basis of the demands for exploring the temporal variations of electrical properties of Earth media in the fixed points of the networks, which would be associated with the earthquake preparation. The observation system is characterized by the high accuracy in measurement, long term stability in operation and high level of rejection to the environmental interference. It consists of three main parts, configuration system measurement system, the calibration and inspection system. 相似文献
9.
磁化率各向异性(AMS)是岩石的普遍特性,它反映岩石磁性矿物的择优取向,即磁组构(Magnetic fabric).近三十年来,磁组构技术逐渐应用于地质和地球物理学,显示广阔的研究前景.测量磁组构的仪器有多种,原理不一,故有必要用同一样品在不同原理的仪器上进行比测,以便确认数据的一致性和可靠性.用黄土、变质岩、玄武岩及掺有铁粉的断层泥制成正方体或圆柱体样品,在卡帕桥(KLY-1和KLY-2)和旋转式磁化率仪(Minisep)上进行比测发现:(1)前者的精度(即重复性)在多数情况下优于后者;2)用旋转式磁化率仪测量之前,必须先测得样品z轴的体磁化率,其标定值取决于厂家在标准样品上标示的数值及被测样品与标准样品的相对体积.就旋转样品测量AMS而言,其标定值应为z轴体磁化率测量标定值的一半. 相似文献
10.
Estimation of instantaneous peak flows from maximum mean daily flows using the HBV hydrological model 下载免费PDF全文
下载免费PDF全文 The record length and quality of instantaneous peak flows (IPFs) have a great influence on flood design, but these high resolution flow data are not always available. The primary aim of this study is to compare different strategies to derive frequency distributions of IPFs using the Hydrologiska Byråns Vattenbalansavdelning (HBV) hydrologic model. The model is operated on a daily and an hourly time step for 18 catchments in the Aller‐Leine basin, Germany. Subsequently, general extreme value (GEV) distributions are fitted to the simulated annual series of daily and hourly extreme flows. The resulting maximum mean daily flow (MDF) quantiles from daily simulations are transferred into IPF quantiles using a multiple regression model, which enables a direct comparison with the simulated hourly quantiles. As long climate records with a high temporal resolution are not available, the hourly simulations require a disaggregation of the daily rainfall. Additionally, two calibrations strategies are applied: (1) a calibration on flow statistics; (2) a calibration on hydrographs. The results show that: (1) the multiple regression model is capable of predicting IPFs with the simulated MDFs; (2) both daily simulations with post‐correction of flows and hourly simulations with pre‐processing of precipitation enable a reasonable estimation of IPFs; (3) the best results are achieved using disaggregated rainfall for hourly modelling with calibration on flow statistics; and (4) if the IPF observations are not sufficient for model calibration on flow statistics, the transfer of MDFs via multiple regressions is a good alternative for estimating IPFs. Copyright © 2015 John Wiley & Sons, Ltd. 相似文献
11.
SD-3A型自动测氡仪在观测中值得注意的几个问题 总被引：2，自引：0，他引：2
论述了数字化气氡仪器SD-3A型自动测氡仪在观测中值得注意的几个问题,特别要注意①气氡观测数据在使用前要经过气温和气压的改正;②闪烁室进水、受到其他气体的污染、补充气体不及时等对观测结果影响是很明显的;③闪烁室在用空气和无水酒精清洗后测值的恢复有一个过程;④仪器标定前应用无水酒精对闪烁室进行清洗,才能提高标定的准确性. 相似文献
12.
活塞-圆桶式固体介质高温高压实验容器的压力标定方法 总被引：1，自引：0，他引：1
固体介质压力标定一般分为2方面。其一是轴压标定,最有效的方法是轴压活塞反复前进和后退,根据活塞循环来获得摩擦力的大小,其中有2个关键环节:1)活塞和样品接触点的确定;2)动摩擦力的确定。其二是围压标定,最有效的方法是利用矿物相变,适用于固体压机压力标定的相变有:石英-柯石英相变、钠长石-硬玉+石英相变,其适合温压范围分别为:500~1200℃、2.5~3.2GPa,600~1200℃、1.6~3.2GPa。我们对2GPa固体介质高温高压实验设备进行了轴压标定,在不同温度、围压、活塞速率等条件下进行了实验,结果表明:围压、温度、活塞运动速率等因素都对动摩擦力有不同程度的影响。因此,轴压标定应该针对不同的实验条件分别进行 相似文献
13.
江苏及邻区地方性震级量规函数的研究 总被引：1，自引：1，他引：0
基于2009～2018年江苏及相邻数字地震台网记录的2602次地震事件观测资料,通过震级残差统计方法得到了72个台站的单台震级与台网平均震级的偏差、平均偏差和标准偏差,分析了震级偏差频次分布和定量统计结果,进而修正了江苏及邻区的地方性震级量规函数。实际地方性震级测定结果表明,使用校正后的量规函数比新震级国家标准(GB17740—2017)中量规函数所测定的震级的标准差更小,且单台震级残差相对更集中于0,这说明该量规函数有助于提高江苏及邻区地方性震级测定精度。 相似文献
14.
15.
16.
If a parameter field to be calibrated consists of more than one statistical population, usually not only the parameter values are uncertain, but the spatial distributions of the populations are uncertain as well. In this study, we demonstrate the potential of the multimodal calibration method we proposed recently for the calibration of such fields, as applied to real-world ground water models with several additional stochastic parameter fields. Our method enables the calibration of the spatial distribution of the statistical populations, as well as their spatially correlated parameterization, while honoring the complete prior geostatistical definition of the multimodal parameter field. We illustrate the implications of the method in terms of the reliability of the posterior model by comparing its performance to that of a "conventional" calibration approach in which the positions of the statistical populations are not allowed to change. Information from synthetic calibration runs is used to show how ignoring the uncertainty involved in the positions of the statistical populations not only denies the modeler the opportunity to use the measurement information to improve these positions but also unduly influences the posterior intrapopulation distributions, causes unjustified adjustments to the cocalibrated parameter fields, and results in poorer observation reproduction. The proposed multimodal calibration allows a more complete treatment of the relevant uncertainties, which prevents the abovementioned adverse effects and renders a more trustworthy posterior model. 相似文献
17.
Łukasz Kaczmarek Tomasz Wejrzanowski Jakub Skibiński Michał Maksimczuk Artur Krzyżak 《Acta Geophysica》2017,65(1):259-268
This paper addresses the issue of the quantitative characterization of the structure of the calibration model (phantom) for b-matrix spatial distribution diffusion tensor imaging (BSD-DTI) scanners. The aim of this study was to verify manufacturing assumptions of the structure of materials, since phantoms are used for BSD-DTI calibration directly after manufacturing. Visualization of the phantoms’ structure was achieved through optical microscopy and high-resolution computed microtomography (µCT). Using µCT images, a numerical model of the materials structure was developed for further quantitative analysis. 3D image characterization was performed to determine crucial structural parameters of the phantom: porosity, uniformity and distribution of equivalent diameter of capillary bundles. Additionally calculations of hypothetical flow streamlines were also performed based on the numerical model that was developed. The results obtained in this study can be used in the calibration of DTI-BST measurements. However, it was found that the structure of the phantom exhibits flaws and discrepancies from the assumed geometry which might affect BSD-DTI calibration. 相似文献
18.
19.
Recent work with stochastic inverse modeling techniques has led to the development of efficient algorithms for the construction of transmissivity (T) fields conditioned to measurements of T and head. Small numbers of calibration targets and correlation between model parameters in these inverse solutions can lead to a relatively large region in parameter space that will produce a near optimal calibration of the T field to measured heads. Most applications of these inverse techniques have not considered the effects of non-unique calibration on subsequent predictions made with the T fields. Use of these T fields in predictive contaminant transport modeling must take into account the non-uniqueness of the T field calibration. A recently developed ‘predictive estimation’ technique is presented and employed to create T fields that are conditioned to observed heads and measured T values while maximizing the conservatism of the associated predicted advective travel time. Predictive estimation employs confidence and prediction intervals calculated simultaneously on the flow and transport models, respectively. In an example problem, the distribution of advective transport results created with the predictive estimation technique is compared to the distribution of results created under traditional T field optimization where model non-uniqueness is not considered. The predictive estimation technique produces results with significantly shorter travel times relative to traditional techniques while maintaining near optimal calibration. Additionally, predictive estimation produces more accurate estimates of the fastest travel times. 相似文献
20.
Remotely sensed (RS) data can add value to a hydrological model calibration. Among this, RS soil moisture (SM) data have mostly been assimilated into conceptual hydrological models using various transformed variable or indices. In this study, raw RS surface SM is used as a calibration variable in the Soil and Water Assessment Tool model. This means the SM values were not transformed into another variable (e.g., soil water index and root zone SM index). Using a nested catchment, calibration based only on RS SM and optimizing model parameters sensitive to SM using particle swarm optimization improved variations in streamflow predictions at some of the gauging stations compared to the uncalibrated model. This highlighted part of the catchments where the SM signal directly influenced the flow distribution. Additionally, highlighted high and low flow signals were mostly influenced. The seasonal breakdown indicates that the SM signal is more useful for calibrating in wetter seasons and in areas with higher variations in elevation. The results identified that calibration only on RS SM improved the general rainfall–runoff response simulation by introducing delays but cannot correct the overall routing effect. Furthermore, catchment characteristics (e.g., land use, elevation, soil types, and precipitation) regulating SM variation in different seasons highlighted by the model calibration are identified. This provides further opportunities to improve model parameterization. 相似文献