首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 125 毫秒
1.
本文以国内川滇甘陕地区263个有详细场地资料的强震台站获得的802组地震动加速度记录为基础,研究了该地区加速度峰值比的总体分布特征,分别探讨了震中距和震级对加速度峰值比的影响特征,按照水平反应谱的标定方法对竖向反应谱进行标定并对其进行了统计分析。统计分析结果显示:竖向与水平向加速度峰值比的概率分布总体服从极值Ⅱ型分布,加速度峰值比均值为0.6,加速度峰值比≤0.65的累积频率为64%;Ⅱ类场地的加速度峰值比随震中距增大而减小;大震近场的加速度峰值比基本上远高于0.65;最后本文给出了不同场地类别下竖向反应谱特征参数,并与水平向反应谱特征参数进行了比较。  相似文献   

2.
将欧洲及其毗邻地区以及美国的部分近场强震记录按照震源机制进行分组,详细的分析了震源机制对水平和竖向分量地震动加速度反应谱放大系数以及竖向与水平向反应谱比值的影响.结果表明震源机制对震级不同的地震动以及地震动不同分量反应谱的影响程度不同;震源机制不仅影响反应谱峰值大小以及峰值位置,还在一定程度上影响反应谱的形状.  相似文献   

3.
水平向加速度峰值比为两条水平向加速度峰值的较大值与较小值的比值;竖向与水平向加速度峰值比为竖向加速度峰值与两条水平向加速度峰值的较小值的比值。以2 129次破坏性地震的156 783组地震动加速度记录为基础,研究水平向、竖向与水平向加速度峰值比值的统计分布特征,对加速度记录按照震中距、震级和震源深度进行分类统计分析。统计分析结果表明:水平向加速度峰值比总体平均值为0.83,水平向加速度峰值比≤0.85的累积概率为63%;竖向与水平向加速度峰值比总体呈现极值Ⅱ型分布特征,竖向与水平向加速度峰值比总体平均值为0.44,竖向与水平向加速度峰值比≤0.65的累积概率为92%。水平向加速度峰值比随震中距的增大而增大,竖向与水平向加速度峰值比随震中距的增大而减小。竖向与水平向加速度峰值比随着震级的增大而增大;在大震(7相似文献   

4.
2008年汶川地震近断层竖向与水平向地震动特征   总被引:12,自引:0,他引:12       下载免费PDF全文
选取分布在北川-映秀中央断裂两侧断层距120 km以内的40个强震动台站的记录,对汶川地震近断层地震动竖向和水平向加速度峰值、速度峰值、竖向和水平向加速度反应谱及谱比值进行了统计分析.研究表明:(1)地震动加速度峰值有显著的上盘效应,经验衰减模型的结果表明,在距地表破裂3~60 km的范围内,龙门山发震断层上盘一侧竖向与水平向的加速度峰值要比衰减模型得到的平均值大30%~40%.上盘的加速度峰值残差大部分是正值,而断层下盘残差大部分为负;水平地震动的东西分量幅值总体要大于南北分量,东西分量衰减相对较慢.(2)地震动长周期成分较弱,加速度反应谱值随周期增大而迅速减小,在周期1.0 s 时,即使在靠近中央断裂的最大加速度反应谱值也只有0.5 g;地震动加速度反应谱谱比值(竖向/水平向)沿龙门山断层周围的分布,在较长周期(T=0.2 s, 0.5 s, 1.0 s)与短周期(T=0.05 s, 0.1 s)有明显的不同.(3)近断层竖向地震动显著,地震动加速度峰值比在(竖向/水平向)可达1.4.在龙门山发震断层的上盘,地震动加速度峰值比整体上比下盘要大,竖向地震动尤为剧烈.部分近断层记录的地震动谱比值(竖向/水平向)在短周期(< 0.1 s)甚至超过1.5,统计分析还表明谱比值在短周期段(< 0.1 s)随断层距的增大而减小.  相似文献   

5.
近断层竖向与水平向加速度反应谱比值特征   总被引:4,自引:2,他引:2       下载免费PDF全文
显著的竖向地震动是近断层地震动区别于远场地震动的重要特征之一,为更合理地确定竖向地震动作用,研究了近断层区域竖向地震动的反应谱特征及其与水平向反应谱比值的影响因素.首先,选取1952—1999年世界范围内震级在M5.4—7.6之间的18次地震的地震动记录,研究竖向地震加速度反应谱及其与水平向加速度反应谱比值特征;然后统计分析了断层距、场地条件、震级以及断层机制对竖向与水平向加速度反应谱比的影响.结果表明,一般情况下竖向加速度具有更丰富的短周期分量,并且竖向加速度反应谱衰减较慢;断层距在20km以内的近断层区域、软弱土层场地、中等震级地震和逆断层大震级中长周期范围等条件下,具有较大的竖向与水平向加速度反应谱比值;在近断层区域的结构抗震设计中应充分考虑竖向地震动的影响.  相似文献   

6.
本文收集了从南北地震带川滇甘陕地区263个有详细场地资料的强震台站获得的802组强震动记录,按照场地、震级和震中距等因素统计分析了竖向与水平向加速度反应谱比的形状以及不同场地、震级和震中距下不同周期段内的谱比平均值,并与建筑抗震规范GB50011—2010规定的0.65进行了比较。结果表明:竖向与水平向加速度反应谱比受场地、震级和震中距等因素的影响; Ⅰ类和Ⅱ类场地在全周期段的谱比均值基本上大于0.65;无论何种分组情况谱比均值在0.1—1.0 s周期范围内基本低于定值0.65,周期大于1.0 s的谱比均值基本上远高于0.65。因此对于大部分抗震规范直接把竖向地震作用取为水平向地震作用的0.65倍,有待商榷。本文建议根据水平向反应谱的标定方式来确定现有竖向强震动记录的竖向地震作用。   相似文献   

7.
选取了1999年9月21日台湾集集7.6级地震主震中68组断层距在20km以内的近断层台站记录和46组断层距在40~70km的东部台站记录,按台站的上下盘位置、场地条件和断层距分组,对其竖向和水平加速度反应谱比值V/H进行了统计分析。研究表明:1)断层的滑动方向和断层破裂的传播方向对断层距在3km以内的台站上的地面运动谱比值V/H有一定影响,且主要体现在中短周期范围内,例如平行断层方向的谱比值要比垂直断层方向的谱比值大。在下盘断层距3~20km的范围内,场地条件对V/H基本没有影响。2)在集集地震中长周期(>3s)部分的谱比值通常>32,且有一个较高的峰值,表明其竖向运动加速度中的长周期分量大于其它地震。3)对于下盘的台站,地面运动在短周期(<0.2s)段的谱比值不随断层距的增加而减少。与中远(>40km)距离的台站相比较,近断层台站的V/H在工程界关心的周期范围内普遍较大。4)场地条件对谱比值V/H的影响在近断层处不显著。在远离断层的东部台站上,硬土场地谱比值V/H在长周期段大于软土场地  相似文献   

8.
近断层竖向地震动峰值特征   总被引:1,自引:0,他引:1  
为了研究近断层区域竖向地震动的加速度峰值衰减特征和竖向与水平加速度峰值比特征,为进行近断层区域结构抗震设计和地震危险性分析等提供基础数据参考,根据1952—1999年世界范围内震级在M5.4-M7.6之间的18次地震的地震动记录提出一种同时考虑断层距和震级影响的竖向峰值加速度衰减关系,并与其他学者提出的衰减关系进行了对比分析。然后初步统计分析了竖向与水平峰值加速度比值、竖向地震动PGV/PGA比值的特征。研究结果表明,本文提出的加速度峰值衰减关系形式比较简单而且能较好地体现地震动加速度峰值的衰减变化关系;断层距在0—40km范围内相当一部分竖向与水平向峰值加速度比值大于一般抗震设计规范中规定的比值即0.65;至少对于竖向地震动而言,只将PGV/PGA〉0.2s作为识别近断层脉冲型地震动的强度指标是不够的。  相似文献   

9.
强震近场加速度峰值比和反应谱统计分析   总被引:12,自引:3,他引:12  
本文对国内外数十次强地震的近场加速度记录进行了统计分析,给出了近场加速度峰值比及反应谱的统计结果,并将统计反应谱与设计反应谱进行了比较。  相似文献   

10.
台湾集集地震近场地震动的上盘效应   总被引:32,自引:12,他引:32       下载免费PDF全文
俞言祥  高孟潭 《地震学报》2001,24(6):615-621
1999年9月21日(当地时间)台湾集集7.6级地震是一个逆断层型地震.用回归分析法对台湾集集地震的加速度峰值数据进行分析,得出了这次地震的水平与垂直向的加速度峰值衰减关系.从残差分布上看,位于断层上盘和下盘上的加速度峰值与从衰减关系所得到的结果相比存在不同的系统偏差,断层上盘地表的加速度峰值较高,而下盘地表的加速度峰值较低.从这次地震的加速度峰值分布等值线图上也可以看出,加速度峰值的分布相对于断层呈现明显的不对称性,上盘衰减较慢而下盘衰减较快.在近断层强地面运动研究、地震危险性分析、设定地震研究与震害预测等工作中,应考虑可能地震的震源机制特点,以便使所用的衰减模型更能反映不同地震环境地区的地震动分布特征.   相似文献   

11.
正SCIENCE CHINA Earth Sciences,an academic journal cosponsored by the Chinese Academy of Sciences and the National Natural Science Foundation of China,and published by Science China Press and Springer,is committed to publishing high-quality,original results in both basic and applied research.  相似文献   

12.
正SCIENCE CHINA Earth Sciences,an academic journal cosponsored by the Chinese Academy of Sciences and the National Natural Science Foundation of China,and published by Science China Press and Springer,is committed to publishing high-quality,original results in  相似文献   

13.
In natural waters arsenic concentrations up to a few milligrams per litre were measured. The natural content of arsenic found in soils varies between 0.01 mg/kg and a few hundred milligrams per kilogram. Anthropogenic sources of arsenic in the environment are the smelting of ores, the burning of coal, and the use of arsenic compounds in many products and production processes in the past. A lot of arsenic compounds are toxic and cause acute and chronic poisoning. In aqueous environment the inorganic arsenic species arsenite (As(III)) and arsenate (As(V)) are the most abundant species. The mobility of these species is influenced by the pH value, the redox potential, and the presence of adsorbents such as oxides and hydroxides of Fe(III), Al(III), Mn(III/IV), humic substances, and clay minerals.  相似文献   

14.
Due to deleterious effects on non-target organisms, the use of organotin compounds on boat hulls of small vessels (<25 m) has been widely prohibited. The International Maritime Organisation (IMO) resolved that the complete prohibition on organotin compounds acting as biocides in antifouling systems should commence in 2008. As a result of restrictions on the use of organotin based paints, other antifouling formulations containing organic biocides have been utilised. This survey was conducted to assess the contamination of replacement biocides in the marine environment following the ban of TBT-based paints. Surface sediments samples were collected in the major ports and marinas along the France Mediterranean coastline (Cote d’Azur) and analysed for organotin compounds, Irgarol 1051, Sea-nine 211TM, Chlorothalonil, Dichlofluanid and Folpet. Every port and marina exhibited high levels of organotin compounds, with concentrations in sediments ranging from 37 ng Sn g−1dry wt in Menton Garavan to over 4000 ng Sn g−1dry wt close to the ship chandler within the port of Villefranche-sur-Mer. TBT degradation indexes suggested that fresh inputs are still made. Among the other antifoulants monitored, only Irgarol 1051 exhibited measurable concentrations in almost every port, with concentrations ranging from 40 ng g−1dry wt (Cannes) to almost 700 ng g−1dry wt (Villefranche-sur-Mer, ship chandler).  相似文献   

15.
Microcystins are cyclic heptapeptide toxins produced by a range of cyanobacterial genera. These cyanobacteria occur naturally in drinking water reservoirs subject to eutrophication, and in rivers and natural lakes. Because of the diversity of organisms, the toxins occur, from oligo‐mesotrophic lakes in North Temperate latitudes, to hypertrophic tropical ponds. The toxins are responsible for numerous cases of injury and death of domestic animals, and human poisoning from drinking water. The initial poisoning includes hepatic cell death. This leads to secondary effects from liver deficiency, including jaundice and photosensitisation. The toxic effects are largely due to inhibition of phosphatase enzymes, acting to regulate protein phosphorylation. The consequences include structural damage, apoptosis and, at lower concentrations, cell cycle effects and tumour promotion. As there is no clear evidence for direct carcinogenesis by microcystins, they are classed as non‐carcinogenic toxins in drinking water. Guideline Values for safe drinking water are derived from data for subchronic rodent toxicity, using the No Observed Adverse Effect Level (the highest dose giving no toxicity). To this dose are applied uncertainty factors, to calculate a Tolerable Daily Intake. On the basis of a standard bodyweight and water consumption the Guideline Value is determined for drinking water. For microcystin‐LR the WHO have set a provisional Guideline Value of 1 μg/L for drinking water.  相似文献   

16.
The geomagnetic field and secular variation exhibit asymmetrical spatial features which are possibly originating from an heterogeneous thermal control of the Earth's lower mantle on the core. The identification of this control in magnetic data is subject to several difficulties, some of which can be alleviated by the use of core surface flow models. Using numerical dynamos driven by heterogeneous boundary heat flux, we confirm that within the parameter space accessible to simulations, time average surface flows obey a simple thermal wind equilibrium between the Coriolis and buoyancy forces, the Lorentz, inertial and viscous forces playing only a secondary role, even for Elsasser numbers significantly larger than 1. Furthermore, we average the models over the duration of three vortex turnovers, and correlate them with a longer time average which fully reveals the signature of boundary heterogeneity. This allows us to quantify the possibility of observing mantle control in core surface flows averaged over a short time period. A scaling analysis is performed in order to apply the results to the Earth's core. We find that three vortex turnovers could represent between 100 and 360 years of Earth time, and that the heat flux heterogeneity at the core-mantle boundary could be large enough to yield an observable signature of thermal mantle control in a time average core surface flow within reach of the available geomagnetic data.  相似文献   

17.
Located in northern Québec, the Lac Shortt Mine was a small gold mine consisting of a thin subvertical orebody which was mined in three main phases. High stress and rockbursting conditions were experienced when ore was extracted in the upper zone between the surface and a depth of 500 metres during the first two phases of mining. Severe rockbursts were experienced in late 1989 near the shaft and in the footwall development following a deepening of the mine shaft to a depth of 830 m and partial development of footwall drift access for the third phase of mining (the mining of the lower zone starting at a depth of 830 m moving upward toward a depth of 500 m). A 16-channel Electrolab MP250 microseismic system, with a Queen's University Full-Waveform piggy-back system, was installed underground at the site due to these problems.It was expected that the thinning sill would be subjected to an ever-increasing load as the thickness of the 500 m sill pillar decreased in the face of the mining excavation from below. A monitoring program consisting of the microseismic monitoring system, a range of conventional geomechanics monitoring tools as well as the undertaking of periodic seismic tomography surveys to assess the ongoing state of stress and rock mass condition within the sill was therefore warranted.The anomalously high-magnitude stress field and the brittle rockmass created a situation in which rockmass failure was common and violent. In the creation and thinning of the sill pillar, the location of banded microseismic activity was crucial in tracing rockmass failure and the associated ground control problems. Reliable source-location determination enabled the identification of areas of stress increase. The movement of the rockmass failure front could be followed, and was responsible for stope dilution, footwall and orebody development deterioration, and caving.Source-mechanism analyses gave accurate double-couple solutions for approximately forty percent of these events having at least ten recognizable polarities. Results suggested movement along vertical north-south striking or vertical east-west striking features. Underground observation of damaged access points showed that vertical north-south striking joints were experiencing failure.The microseismic activity, which was consistently concentrated close to the southwest and northeast corners of current production stopes, could be explained by a stress field oriented obliquely to the strike of the orebody, as measured prior to shrinkage of the sill pillar byin situ stress measurements and observed borehole overbreaks. The orientations of theP andT axes for the microseismic activity further confirmed that the stress field oriented obliquely to strike.While an increase in compressional-wave velocity of 2.3 percent, corresponding to a measured stress increase of approximately 10 MPa could be measured by repeated tomographic surveys, it was relatively small and only a factor of two or so above the velocity measured uncertainty. The relative insensitivity of thein situ rock mass modulus to the applied stress is believed to be largely due to the rockmass discontinuities being relatively closed prior to stress increase, as substantiated by the small deformations seen by the extensometer and borehole camera. This situation existed because of the very high pre-mining stress level.The experimental demonstration that the rock could not absorb substantially increased load through the mechanism of discontinuity closure or tightening (which would be reflected in the modulus) may be evidence in itself of potentially burst-prone ground, such as encountered at Lac Shortt.  相似文献   

18.
《水文科学杂志》2013,58(4):704-712
Abstract

The upper Niger and Volta rivers exhibit a great and highly contrasting variability of inter-annual runoff. The Bani River, the largest tributary to the Niger River in Mali, shows a dramatic decrease in runoff after the 1970s, with the result that many boreholes in the region have dried up since the drought began. In contrast, the Nakambe River (Upper Volta basin, in Burkina Faso) shows an increase in runoff for the same period, leading to unexpected flood peaks that damaged infrastructures. The contribution that the groundwater and its variability make to surface runoff variability is assessed in this study by comparing the data of the national groundwater monitoring networks of Mali and Burkina Faso to surface runoff. Several variables are compared at the basin scale: the date of the maximum level of the water table, the annual rainfall, discharge, low flows and depletion coefficients. Variability in the low flows of the Bani River is well correlated to a decrease in the water table. Since 1970, the greater decrease in runoff in comparison to the rainfall decrease is due to a reduction in the baseflow, related to the cumulated rainfall deficit. Concerning the Nakambe River, the runoff increase is not supported by a water table increase, but is due to the increase in runoff coefficient related to land degradation.  相似文献   

19.
The inability to detect the presence of viable Helicobacter pylori bacteria in environmental waters has hindered the public health community in assessing the role water may play in the transmission of this pathogen. This work describes a cultural enrichment method coupled with an H. pylori‐specific PCR to identify these bacteria in water. While far from perfected at the present time, this represents an exciting new approach to studying the significance of water as a transmission mechanism for H. pylori. Evidence is presented that indicates culturable H. pylori bacteria were found using this enrichment/PCR method in a local groundwater source.  相似文献   

20.
To realistically assess the seismic risk relating to built infrastructures in Hong Kong and in the neighbouring coastal cities of southern Guangdong province, it is necessary to predict ground shaking induced by different earthquake scenarios with good accuracy. A companion paper has described the modelling of the spatial and temporal distribution of the diffused seismic activities in the region, based on the newly-developed ‘Expanding Circular Disc’ (ECD) method. Representative Magnitude–Distance (M–R) combinations for both near-field and far-field earthquakes (in relation to Hong Kong) have been derived using the ECD method. The present paper describes the modelling of the response spectrum on rock sites associated with the predicted M–R combinations, using the Component Attenuation Model (CAM) that was also developed recently by the authors, based on stochastic simulations of the seismological model. The significant effects of soil resonance on the response spectrum are described in a separate publication.The accuracy of CAM in modelling ground motion properties on rock sites has been tested here by comparisons with (i) strong motions recorded in Taiwan and South China from the 1999 ‘Chi-Chi’ earthquake in Taiwan (M=7.6), (ii) motions recorded in South China from another earthquake occurring in the southern Taiwan Strait in the same year (M=5.1), and (iii) historical seismic intensity data obtained within South China. The overall capability of CAM in modelling both near-field and far-field attenuation has been shown to be unmatched by existing empirical models. Results of the comparison studies confirm the accuracy of CAM, particularly within an epicentral distance of 300–400 km.This study shows that the developed serviceability response spectra (i.e. at short return periods) are controlled mainly by the earthquake recurrence behaviour of major distant seismic sources. In contrast, the ultimate response spectra (i.e. at long return periods) relate to events with magnitudes close to the maximum credible earthquake (MCE) limit, the effect of which may also be represented by the Characteristic Response Spectrum (CRS). Both types of earthquake scenario can be significantly affected by the regional crustal properties. The proposed response spectrum envelopes have been compared with previously developed recommendations, and a critical review has been conducted. The intrinsic advantages of the ECD–CAM modelling approach have been highlighted, emphasising its directness and transparency when compared with the more complex process required to implement traditional Probabilistic Seismic Hazard Assessment (PSHA).  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号