共查询到20条相似文献，搜索用时 62 毫秒
1.
王水溶样-电感耦合等离子体发射光谱法同时测定铁铜铅锌硫化物矿石中8个元素 总被引：5，自引：5，他引：0
建立了王水溶样-电感耦合等离子体发射光谱法同时测定铁、铜、铅、锌硫化物矿中Cu、Pb、Zn、As、Ag、Cd、Hg和Mo等8个元素的分析方法。确定了方法的溶矿及测定条件,用国家一级标准物质GBW07162(多金属贫矿石)和GBW07164(多金属矿石)进行精密度实验,除个别元素外,大多数的元素精密度(RSD,n=11)小于5%,准确度(RE)小于10%。通过一系列硫化物矿石标准物质进行方法验证,检测结果基本都在标准值的误差范围内,符合地质矿产开发的要求。方法简单,同时测定元素较多,线性范围宽,检出限低,尤其有利于硫化物矿石中的亲硫元素As、Ag、Hg的分析,实用性强。 相似文献
2.
《矿物岩石地球化学通报》2016,(3)
铅矿石在电感耦合等离子体质谱测定中,元素Pb的双电荷离子206Pb~(2+)干扰内标元素103Rh而影响其他元素的测定结果。本文建立了用~(105)Pd和~(187)Re的混合溶液为内标溶液,封闭酸溶-电感耦合等离子体质谱测定硫化铅矿石中的铍、钪、钛、铬、钴、镍、铜、锌、镓、锗、砷、锑和稀土等40种微量元素分析方法,提高了电感耦合等离子体质谱分析铅矿石中低质量的元素(质量为133Cs以下的元素)测定数据的准确度。通过大量的实验确定了该方法的检出限为0.04~5.00μg/g,对国家一级标准物质GBW07235(铅矿石)、GBW07236(铅矿石)、GBW07286(铜铅锌矿石)、GBW07287(铅锌矿石)、GBW07165(富铅锌矿石)、GBW07172(铅矿石)进行分析测定,其准确度(RE)均小于10%,加标回收率为90%~120%。 相似文献
3.
采用微波消解-电感耦合等离子体质谱法(ICP-MS)测定了镓、锗、铟、铊矿石中的15种稀土元素,本法的检出限为(0.003~0.015)μg/g,相对标准偏差在1.11%~2.92%之间,加标回收率在95.5%~105.9%之间,通过分析国家标准物质GBW07103、GBW07106和GBW07120来验证方法的准确度,测定值和标准值吻合,表明此方法具有操作简便,检出限低,线性范围宽,精密度高,准确度好等优点,能满足岩石矿物中的稀土元素的检测要求。 相似文献
4.
使用王水溶矿-电感耦合等离子体发射光谱法同时测定铜铅锌矿石中的铜铅锌。用国家一级标准物质GBW07233(铜矿石成分分析标准物质)、GBW07236(铅矿石成分分析标准物质)、GBW07237(锌矿石成分分析标准物质)和GBW07286(铜铅锌矿石成分分析标准物质)进行验证,测定值与标准值相符,结果准确可靠。方法操作简单,分析快速,提高了分析大批量样品的工作效率。 相似文献
5.
《矿产与地质》2017,(6)
锡矿成分复杂,具有丰富的共生和伴生资源。锡矿尾砂中的重金属元素检测是锡矿矿区土壤风险评估和土壤环境重建的重要依据。采用硝酸-高氯酸-氢氟酸体系对样品进行了前处理,通过优化仪器条件,加入~(103)Rh标准溶液作为内标,选择~(52)Cr、~(59)Co、~(60)Ni、~(63)Cu、~(66)Zn、~(114)Cd和208 Pb作为测定同位素,建立了电感耦合等离子体质谱仪(ICP-MS)同时测定锡矿尾砂中的铜铅锌镉铬钴镍的分析方法。测定结果表明,各元素的标准曲线线性相关系数都在0.9999以上,检出限为0.003~0.12μg/L,精密度介于0.78%~3.71%之间,样品加标回收率为97.2%~103%。用本方法对锡矿石GBW07282和钨矿石GBW07240标准物质进行了分析,各元素的测定结果与标准认定值相符。 相似文献
6.
偏硼酸锂碱熔-电感耦合等离子体发射光谱法测定硫化物矿中硅酸盐相的主成分 总被引：5，自引：4，他引：1
通过实验发现偏硼酸锂不能有效分解硫化物矿,但可有效分解其中以氧化物存在的造岩元素,从而可测定硫化物矿中硅酸盐相的二氧化硅、三氧化二铝、氧化钙、氧化镁、氧化钾、氧化钠、二氧化钛、氧化锰、五氧化二磷共9个主要组分。实验确定了用电感耦合等离子体发射光谱法测定硫化物矿的分解条件及测定条件。对铜、铅、锌(银)矿石与精矿成分分析标准物质GBW 07162~GBW 07168以及硫化物单矿物标准物质GBW 07267~GBW 07270进行分析测定,方法精密度(RSD)<7%,准确度(RE)<5%,能够满足样品分析中各元素定量分析的要求。同时向定值不全的硫化物标准物质中加岩石标样GBW 07105做流程加标试验,回收率大部分在90%~110%。 相似文献
7.
采用粉末样品压片制样,水系沉积物及土壤国家一级标准物质作为标准,使用经验系数法和散射线内标法校正元素间的吸收增强效应,用X射线光谱仪对土壤样品中的Fe_2O_3、Cao、Cl、S、As、Ba、Br、Ce、Co、Cr、Ni、Cu、Zn等34种主次痕量元素进行测定,用国家一级标准物质GBW07452(GSS-23),GBW07405(GSS-5)和GBW07404(GSS-4)分析检验准确度和精密度,分析结果与标样标准值吻合,除Cl、S、As、Br、Ce、Co、Ni、Th、Sc、Hf、Nb、Nd的精密度小于10.00%以外,其他各元素精密度均在5.00%以内,各元素检出限均满足化探要求。 相似文献
8.
文章研究了三酸溶样,电感耦合等离子体发射光谱（ICP—AES）测定铜精矿中Ag的质量分数,为了避免共存元素的干扰,采用国家一级标准物质GBW07166和GBW07205作为标准物质对仪器分析测试条件及方法的准确度,精密度作了相应的讨论,实验表明方法准确,可靠快速,结果令人满意。 相似文献
9.
电感耦合等离子体发射光谱法测定铅锌矿中15个主次量元素 总被引：3，自引：2，他引：1
铅锌矿多元素同时测定中,样品预处理过程受多种不同因素的影响,单因素试验往往无法同时为多因素实验提供合理的优化方案。本文采用盐酸-硝酸溶矿,考察了样品预处理过程中混合酸配比、混合酸体积、消解时间及消解温度对消解效果的影响,利用正交试验设计及极差分析确定了最优消解条件:盐酸-硝酸混合酸配比3∶1,混合酸体积10 m L,消解时间120 min,消解温度90℃,用电感耦合等离子体发射光谱法同时测定铅锌矿中15个主次量元素(铅锌铜锰砷银铋镉钴镍镓铟钼锗锑)的含量。在最优条件下,用富铅锌矿石国家标准物质(GBW 07165)进行试验,大多数元素的精密度(RSD,n=12)和准确度小于5%,方法检出限为0.0019~0.048μg/g。基于铅锌矿主要是以硫化物形式存在,采用一系列硫化物国家标准物质验证方法的准确度及可行性,检测结果基本都在标准值的误差范围内。应用该方法分析湖南某矿区中大批量铅锌矿样品,标样质量统计合格率为100%,密码质量统计合格率大于97%。 相似文献
10.
微波消解电感耦合等离子体质谱法测定黑色页岩中稀有稀土元素 总被引：8，自引：6，他引：2
采用硝酸-氢氟酸-过氧化氢于微波消解仪中分解样品,电感耦合等离子体质谱法测定贵州遵义地区某黑色页岩中稀有稀土元素的含量。对页岩标准物质(GBW 07107)和水系沉积物地球化学成分分析标准物质(GBW07305、GBW 07310)的分析,测定值与标准值相一致。对黑色页岩的分析结果较好,方法精密度(RSD,n=6)各元素均小于4%,加标回收率为97.9%~100.1%。方法准确度高、简单、快捷,一次溶样可同时测定多种元素。 相似文献
11.
S. Viswanathan K. Surya Prakash Rao B. Mahabaleswar 《Journal of the Geological Society of India》2013,82(6):621-627
Komatiites are mantle-derived ultramafic volcanic rocks. Komatiites have been discovered in several States of India, notably in Karnataka. Studies on the distribution of trace-elements in the komatiites of India are very few. This paper proposes a simple, accurate, precise, rapid, and non-destructive wavelength-dispersive x-ray fluorescence (WDXRF) spectrometric technique for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in komatiites, and discusses the accuracy, precision, limits of detection, x-ray spectral-line interferences, inter-element effects, speed, advantages, and limitations of the technique. The accuracy of the technique is excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Zr, Nb, Ba, Pb, and Th and very good (within 4%) for Y. The precision is also excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th. The limits of detection are: 1 ppm for Sc and V; 2 ppm for Cr, Co, and Ni; 3 ppm for Cu, Zn, Rb, and Sr; 4 ppm for Y and Zr; 6 ppm for Nb; 10 ppm for Ba; 13 ppm for Pb; and 14 ppm for Th. The time taken for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in a batch of 24 samples of komatiites, for a replication of four analyses per sample, by one operator, using a manual WDXRF spectrometer, is only 60 hours. 相似文献
12.
E. M. Prasolov S. A. Sergeev B. V. Belyatsky E. S. Bogomolov K. A. Gruzdov I. N. Kapitonov R. Sh. Krymsky V. O. Khalenev 《Geochemistry International》2018,56(1):46-64
This paper reports the first results of a study of 11 isotope systems (3He/4He, 40Ar/36Ar, 34S/32S, 65Cu/63Cu, 62Ni/60Ni, 87Sr/86Sr, 143Nd/144Nd, 206–208Pb/204Pb, Hf–Nd, U–Pb, and Re–Os) in the rocks and ores of the Cu–Ni–PGE deposits of the Norilsk ore district. Almost all the results were obtained at the Center of Isotopic Research of the Karpinskii All-Russia Research Institute of Geology. The use of a number of independent genetic isotopic signatures and comprehensive isotopic knowledge provided a methodic basis for the interpretation of approximately 5000 isotopic analyses of various elements. The presence of materials from two sources, crust and mantle, was detected in the composition of the rocks and ores. The contribution of the crustal source is especially significant in the paleofluids (gas–liquid microinclusions) of the ore-forming medium. Crustal solutions were probably a transport medium during ore formation. Air argon is dominant in the ores, which indicates a connection between the paleofluids and the atmosphere. This suggests intense groundwater circulation during the crystallization of ore minerals. The age of the rocks and ores of the Norilsk deposits was determined. The stage of orebody formation is restricted to a narrow age interval of 250 ± 10 Ma. An isotopic criterion was proposed for the ore-bearing potential of mafic intrusions in the Norilsk–Taimyr region. It includes several interrelated isotopic ratios of various elements: He, Ar, S, and others. 相似文献
13.
14.
奥地利安东帕有限公司 《岩矿测试》2009,28(3):306-306
最新的流行病学研究表明,空气中较高浓度的悬浮细颗粒可能对人类的健康有不利的影响。根据该项研究显示,由于心脏病、慢性呼吸问题和肺功能指标恶化而导致死亡率的升高与细尘粒子有关。这些研究结果已经促使欧盟于1999年4月出台了限制空气中二氧化硫、二氧化氮、氧化氮、铅和颗粒物含量的法案(1999/30/EC),对各项指标包括对可吸入PM10颗粒的浓度提出了新的限制性指标。PM10颗粒是指可以通过预分级器分离采集的气体动力学直径小于10μm的细颗粒。目前研究的兴趣重点逐步偏向PM2.5这些更细微颗粒物,PM2.5这种颗粒物对健康有明显的不利影响。在欧盟指令2008/50/EC中,对PM10和PM2.5都提 相似文献
15.
16.
Mining induced subsidence can significantly affect mining costs where major surface facilities and natural environment need to be protected. Overburden grout injection is a technology used to control coal mine subsidence by injecting the mine waste material extracted from the coal back into the inter-burden rock during longwall mining. The flowing slurry is here categorised as a nonlinear viscous cohesive (Bingham plastic) fluid. During longwall mining the grout slurry is pumped into the separated beds of the rock mass through a central vertical borehole, which is drilled deep into the inter-burden rock strata above the coal seam. However, a blockage can occur in the injection system when the slurry velocity falls below a certain critical threshold velocity, indicating a material phase change from cohesive-viscous to cohesive-frictional. In situ field injection tests through boreholes have been simulated at a smaller scale at the CSIRO laboratory in Brisbane by pumping the slurry through a radial disk (gap = 4 mm) from its centre. Laboratory experiments indicate a general, nonlinear, cohesive, viscous, frictional model for shear behaviour of the slurry, in which the material shear parameters are functions of the disk radial distance. Complete dimensional and dimensionless analytical solutions have been developed based on an approach related to Bingham–Herschel–Bulkley fluid mechanics. The derived formulae include relations for minimum pump pressure, local pressure and pressure gradient, wall shear stress, volume rate, velocity and velocity gradient. The theoretical results match the experimental measurements. The experiments covered slurries with maximum particle sizes of 0.5 to 2 mm with about 50% being larger than 100 µm. The viscosities at the various solids concentrations were measured with a standard torsion viscometer. This study differs from the previous research in several distinct aspects, namely, consideration of the variable shear parameters rather than fixed values, inclusion of total nonlinear behaviour, and implementation of a friction function to mimic behaviour of the deposited and consolidating stiff slurry, which can cause a significant pressure rise as a result of the increased shear resistance. 相似文献
17.
Alexander E. C. Broberg J. S. Kehren A. R. Graziani M. M. Turri W. L. 《Environmental Geology》1993,22(4):353-361
Bellechester, Minnesota, is a small community of approximately 155 residents located on the county line between Goodhue and Wabasha counties in southeast Minnesota's karst region. Bellechester is served by a 21-year-old wastewater treatment facility (WWTF) consisting of three waste-stabilization ponds. On 28 April 1992 six sinkholes were discovered to have drained cell 2 of the WWTF resulting in the loss of approximately 8.7×106 1 of partially treated effluent and about 600 m3 of soil into previously undetected subsurface voids of unknown dimensions. In the week following the collapse, approximately 200 water wells located within a 5-km radius of the WWTF were sampled in an after-the-fact, emergency sampling program. Twelve samples with elevated fecal coliform levels, 18 samples with nitrate-nitrogen greater than the 10 mg/1 standard, and no samples with elevated chlorides were found. However, the elevated levels could not be unambiguously attributed to the WWTF collapse. This is the third WWTF to fail by sinkhole collapse in southeast Minnesota since 1974. All three collapsed lagoons have been located in similar geomorphic and stratigraphic settings. However, at least two lagoons have collapsed in the adjacent area in northeast Iowa, and these lagoons are located at different stratigraphic positions. Twenty-two WWTFs constructed in southeast Minnesota's karst region in the last 25 years have been identified as subject to potential sinkhole collapse. An unknown but significant number of manure storage lagoons, flood control structures, etc., have also been constructed in the karst region and are at risk. Public agencies are beginning to develop plans to deal with the risk associated with existing and future waste lagoons in this environment. The critical hydrogeologic parameters that can be used to prioritize the risk of collapse at existing facilities include: (1) the lithology of the first bedrock beneath each lagoon, (2) the thickness of surficial materials between the lagoon and the bedrock surface, (3) the presence and construction of liners (seepage rate), and (4) the proximity to existing sinkholes. 相似文献
18.
岩石密度和超高压岩石折返速率 总被引：1，自引：3，他引：1
在常温常压条件下对中国大陆科学钻CCSD主孔100-3000米岩心样品进行了密度测量,建立了密度连续剖面,并界定了不同超高压岩石的密度值。通过对比高温高压物性实验资料,岩石密度随着退变程度增强而降低,榴辉岩密度变化序列为3.52g/cm3→3.49g/cm3→3.07g/cm3→2.93g/cm3。超高压长英质岩石密度变化序列为3.00g/cm→2.80g/cm3→2.65g/cm3。上述实验资料是讨论不同折返阶段岩石所受浮力的基础,为研究折返速率大小提供了基本参数。本文通过折返板块运动平衡时,上浮力与粘滞力平衡这一关系式,定量研究了大陆俯冲板块的折返速率,认为密度差产生上浮力从而引起折返,温度对板块折返速率的影响最为显著;密度差大小、折返角度、折返板块大小对折返速率也有直接的影响。定量模拟分析表明,在温度高于850℃时,板块的折返速率可以超过100mm/a;当温度降至700℃时,折返速率则低于1.5mm/a。作者认为在折返早期,温度较高,板块快速折返至60-70km榴辉岩相深度;随着传导散热,温度降低,板块以较慢的速率折返至中下地壳。折返速率的估算表明,浮力是板块折返第一阶段(从>100km深部折返至<40km的中下地壳)的主要驱动力。 相似文献
19.
20.
滇东南锡、银、铅、锌多金属矿床主要分布在个旧、白牛厂、都龙3个矿区,而滇东南较大的3个花岗岩体又分别出露在3个矿区或附近.花岗岩体均形成于燕山晚期,岩石化学、矿物成分相似,富含锡、银、铅、锌、钨、铜等成矿元素.矿床主金属元素组合与岩体之间的距离由远而近出现由锡、钨、(铍、铌、钽)→锡、钨、(铁)、铜、铟→锡、铅、锌、银、铟、(锑)有规律的变化.花岗岩浆是成矿物质来源和成矿热源.岩浆侵入初期使上覆地层隆起产生背斜(凹陷部位成向斜);同时使地层产生一系列裂隙、压性断层或层间断裂;岩浆侵入晚期,这些断层再次活动,表现为张性,岩浆产生的含矿热液沿由其活动所造成的断裂迁移、充填、交代、沉淀而形成矿床. 相似文献