共查询到20条相似文献，搜索用时 46 毫秒
1.
The Menilite Shales (Oligocene) of the Polish Carpathians are the source of low-sulfur oils in the thrust belt and some high-sulfur oils in the Carpathian Foredeep. These oil occurrences indicate that the high-sulfur oils in the Foredeep were generated and expelled before major thrusting and the low-sulfur oils in the thrust belt were generated and expelled during or after major thrusting. Two distinct organic facies have been observed in the Menilite Shales. One organic facies has a high clastic sediment input and contains Type-II kerogen. The other organic facies has a lower clastic sediment input and contains Type-IIS kerogen. Representative samples of both organic facies were used to determine kinetic parameters for immiscible oil generation by isothermal hydrous pyrolysis and S2 generation by non-isothermal open-system pyrolysis. The derived kinetic parameters showed that timing of S2 generation was not as different between the Type-IIS and -II kerogen based on open-system pyrolysis as compared with immiscible oil generation based on hydrous pyrolysis. Applying these kinetic parameters to a burial history in the Skole unit showed that some expelled oil would have been generated from the organic facies with Type-IIS kerogen before major thrusting with the hydrous-pyrolysis kinetic parameters but not with the open-system pyrolysis kinetic parameters. The inability of open-system pyrolysis to determine earlier petroleum generation from Type-IIS kerogen is attributed to the large polar-rich bitumen component in S2 generation, rapid loss of sulfur free-radical initiators in the open system, and diminished radical selectivity and rate constant differences at higher temperatures. Hydrous-pyrolysis kinetic parameters are determined in the presence of water at lower temperatures in a closed system, which allows differentiation of bitumen and oil generation, interaction of free-radical initiators, greater radical selectivity, and more distinguishable rate constants as would occur during natural maturation. Kinetic parameters derived from hydrous pyrolysis show good correlations with one another (compensation effect) and kerogen organic-sulfur contents. These correlations allow for indirect determination of hydrous-pyrolysis kinetic parameters on the basis of the organic-sulfur mole fraction of an immature Type-II or -IIS kerogen. 相似文献
2.
Eric Lehne Volker Dieckmann Rolando di Primio Andreas Fuhrmann Brian Horsfield 《Organic Geochemistry》2009,40(5):604-616
Asphaltenes extracted from crude oils are proposed to possess structural features of the related source rock kerogen. For the present study micro-scale sealed vessel pyrolysis (MSSV) and combustion isotope ratio mass spectrometry (GC–C–IRMS) were used to compare gas generation from a whole rock (type II-S kerogen) from southern Italy with that from related sulfur rich asphaltenes isolated from a low maturity heavy crude oil. The purpose of was to determine whether experimental pyrolysis of oil asphaltenes can be used to predict the timing and the chemical and isotopic composition of hydrocarbon gases generated from genetically related kerogen in the source rock during burial maturation. The results show that parameters such as (gas to oil ratio) GOR and oil and gas formation timing are very similar for these two sample types, whereas gas composition, product aromaticity and sulfur content are remarkably different. Slight differences in GOR are mainly due to differences in gas formation characteristics at very high levels of thermal alteration. Secondary gas formation from the whole rock covers a much broader temperature range under geological conditions than that from the asphaltene products. However, it is remarkable that both the onset and the maximum temperature are nearly identical under geological conditions. The observed differences in gas generation characteristics are supported by discrepancies in the carbon isotopic characteristics of the gas range compounds and indicate different precursors and/or mechanisms for gas generated from whole rock and asphaltenes. 相似文献
3.
干酪根、煤以及显微组分生烃过程中的动力学参数(如活化能分布特征等)是其内部分子结构的宏观反映,据此可以判断有机质内部成键特征,评价生油门限、生油高峰,计算不同温度范围油气生成量等。笔者利用岩石热解仪(Rock-Eval型)对贵州水城含树皮体煤中的主要组成——基质镜质体的成烃动力学特征进行了研究,并与树皮体、丝质体进行比较,结果表明,基质镜质体的平均活化能为200kJ/mol,大于树皮体的平均活化能(177kJ/mol),而小于丝质体的平均活化能(324kJ/mol),由此推断,在相同的热演化条件下,基质镜质体、树皮体、丝质体三者的生烃顺序为树皮体→基质镜质体→丝质体。从基质镜质体生烃活化能分布特征图上可以看出,基质镜质体有4次主要生烃期,其对应的活化能分布范围及产烃率分别为191.25—192.5kJ/mol、12.19%,195—196.25kJ/mol、7.25%,197.5—198.75kJ/mol、39.82%,216.25kJ/mol、18.64%,据此可以认为:基质镜质体主要由4种不同类型键组成。在活化能191.25—198.75kJ/mol范围内,基质镜质体的累计生烃率达60%左右,这说明基质镜质体产烃较集中(在较短的地质剖面或温度范围内形成大量烃类物质),其含量高(煤岩三大组分之一),因此对煤成烃资源有较大的贡献。 相似文献
4.
Hydrothermal pyrolysis of organic matter in Riphean mudstone 总被引：1，自引：0，他引：1
V. N. Melenevsky A. E. Kontorovich Wuu-Liang Huang A. I. Larichev T. A. Bul’bak 《Geochemistry International》2009,47(5):476-484
The catagenesis of organic matter (OM) was modeled by the hydrothermal pyrolysis of a source rock (Riphean mudstone from eastern Siberia). Isothermal experiments 72-h long were carried out in an aqueous environment in autoclaves at temperatures of 300, 310, 320,..., 370°. The pyrolysis products were analyzed for yield of extract, organic carbon, and parameters of Rock-Eval pyrolysis. The amount of the generated liquid hydrocarbon (HC) compounds increased to a temperature of 340°C and then decreased. The experimental trend of the hydrogen index (HI) dependence on the T Max temperature generally coincided with that for natural OM maturation. The carbon isotopic composition of the insoluble (in organic solvents) OM remained practically unchanged in the course of the experiments. The carbon structure of the solid remnants of the experimental samples was ordered (after the experiments) with the origin of turbostratic graphite with a spacing of d 002≈3.5 A°. We also conducted pyrolysis in a diamond anvil cell equipped with a digital camera in order to obtain additional qualitative and quantitative information on oil generation and emigration in the source rock and isolated kerogen. Chemical kinetic parameters of kerogen cracking were calculated for pyrolysis in an open system. The extrapolation of the high-temperature experimental results is discussed with reference to natural OM maturation. 相似文献
5.
对鄂尔多斯盆地奥陶系平凉组海相页岩进行了3种升温速率下的 Rock-Eval 热解模拟实验,研究了其干酪根在开放体系下的热解生烃演化特征.通过分析热解烃 S2的产率随温度的变化,结合 Kinetics 生烃动力学专用软件计算,获得了其开放体系下的生油动力学参数,活化能分布范围为(57~81)×4.185 kJ/mol.在此基础上进行的动力学模拟结果与实验数据非常吻合,可较好地将实验数据外推到地质实际过程.此外,发现热解残渣中的 H/C(原子比)值与热解温度、干酪根转化率有较好的相关关系,可建立 H/C 值与转化率或者等效镜质组反射率的可靠模板,表明 Rock-Eval 热解实验与 H/C 值结合,可快速评价下古生界源岩的成熟度、转化率和生烃量等指标,将其应用于资源量计算等方面 相似文献
6.
海相干酪根与原油裂解气甲烷生成及碳同位素分馏的差异研究 总被引：10，自引：3，他引：10
利用封闭金管高压釜体系对海相原油和成熟干酪根进行了热解生气实验,获取了两类裂解气的组分和甲烷碳同位素数据,对比研究了两类母质在生气机理上的差异,并借助碳同位素分馏动力学参数讨论了甲烷碳同位素分馏的异同点.结果表明,原油裂解气富含C2-5重烃,其后期裂解是甲烷的重要来源;而干酪根裂解气中C2-5的含量较低,其后期裂解对干酪根甲烷气的贡献较小.这是两类甲烷气体生成的最大差异之一.两类裂解气甲烷碳同位素都有随着热解温度增高,碳同位素值先变轻再变重的特点,但原油裂解气甲烷碳同位素的最小值对应的温度较高;在相同热解温度下,干酪根裂解气甲烷碳同位素值要重于原油裂解气甲烷碳同位素值,这与后者前系物经过多次碳同位素分馏有关.因此,生气机理的差异是造成同位素分馏差异的根本原因,两类甲烷气体碳同位素分馏动力学参数的差异也是有成因意义的. 相似文献
7.
V. N. Melenevskii 《Geochemistry International》2012,50(5):425-436
The catagenesis of organic matter (OM) was modeled by the hydrous pyrolysis of a Riphean mudstone. Microscopic observations
of the processes operating during kerogen heating to 600°C were conducted in a diamond anvil cell. The results of pyrolysis
in an aqueous environment were used to calculate the activation energies of kerogen cracking and derive chemical kinetic models
for OM catagenesis. Isothermal experiments were carried out for 3 days at temperatures of 300, 310, …, 360, and 370°C. The
maximum bitumen yield was obtained at 330°C followed by thermal cracking at higher temperatures. The aromatic and saturated
hydrocarbons from rock bitumen, hydrous pyrolyzates, and kerogen flash pyrolyzates were analyzed by chromatography-mass spectrometry.
We also discuss the problem of extrapolation of high-temperature pyrolysis results to geologic observations under the conditions
of regional catagenesis. 相似文献
8.
利用干酪根热解动力学模拟实验研究塔里木盆地下古生界古地温 总被引：9，自引：0，他引：9
通过热解动力学模拟实验，对塔里木盆地塔参1井奥陶系干酪根的热演化过程进行了模拟，以此基础上利用KINETICS软件求取干酪根镜质体反射率（R0）的生成动力学参数，并结合塔参1井的沉积埋藏史，计算塔参1井寒武－奥陶系的古地温，这对于研究塔里木盆地下古生界高过成熟烃源岩的古地温是一种新方法。 相似文献
9.
Transition metals in source rocks have been advocated as catalysts in determining extent, composition, and timing of natural gas generation (Mango, F. D. (1996) Transition metal catalysis in the generation of natural gas. Org. Geochem.24, 977-984). This controversial hypothesis may have important implications concerning gas generation in unconventional shale-gas accumulations. Although experiments have been conducted to test the metal-catalysis hypothesis, their approach and results remain equivocal in evaluating natural assemblages of transition metals and organic matter in shale. The Permian Kupferschiefer of Poland offers an excellent opportunity to test the hypothesis with immature to marginally mature shale rich in both transition metals and organic matter. Twelve subsurface samples containing similar Type-II kerogen with different amounts and types of transition metals were subjected to hydrous pyrolysis at 330° and 355 °C for 72 h. The gases generated in these experiments were quantitatively collected and analyzed for molecular composition and stable isotopes. Expelled immiscible oils, reacted waters, and spent rock were also quantitatively collected. The results show that transition metals have no effect on methane yields or enrichment. δ13C values of generated methane, ethane, propane and butanes show no systematic changes with increasing transition metals. The potential for transition metals to enhance gas generation and oil cracking was examined by looking at the ratio of the generated hydrocarbon gases to generated expelled immiscible oil (i.e., GOR), which showed no systematic change with increasing transition metals. Assuming maximum yields at 355 °C for 72 h and first-order reaction rates, pseudo-rate constants for methane generation at 330 °C were calculated. These rate constants showed no increase with increasing transition metals. The lack of a significant catalytic effect of transition metals on the extent, composition, and timing of natural gas generation in these experiments is attributed to the metals not occurring in the proper form or the poisoning of potential catalytic microcosms by polar-rich bitumen, which impregnates the rock matrix during the early stages of petroleum formation. 相似文献
10.
海相碳酸盐岩烃源岩热解动力学研究:全岩和干酪根的对比 总被引：12，自引：3，他引：9
我国海相碳酸盐岩地层分布广泛,厚度巨大,经历的地质历史较长,特点是有机质丰度低,多处于高过成熟阶段.碳酸盐岩烃源岩评价对我国的油气资源评价与勘探至关重要.用生烃动力学方法来研究碳酸盐岩生油气过程是一个值得探索的研究方向.本文通过生烃动力学热模拟实验,求取了碳酸盐岩全岩和其干酪根不同烃类组分(甲烷、 C2～ C5气态烃)的生成动力学参数并进行对比.结果表明,在生烃动力学热解实验中,全岩和其干酪根具有相似的动力学参数,采用烃源岩应该比干酪根更符合实际,但是干酪根样品可以测得更为详细的实验数据,因此可以根据样品的情况,选择合理且易行的实验条件.在此基础上,以本文得到的参数作为参照指标,用动力学方法外推到地质实际中,可准确地提出适合我国的碳酸盐岩生烃定量模型,能为碳酸盐岩的资源评估等方面给出定量数值,从而为有效烃源岩的定量评价提供一种新的方法和途径. 相似文献
11.
I. Lerche 《Mathematical Geology》1991,23(1):137-155
Several different proposed models of thermocatalytic cracking of kerogen to hydrocarbons are exhibited. The specific models are then combined into a single generic, encompassing framework. For laboratory pyrolysis measurements of kerogen degradation and of thermal generation of hydrocarbons, inverse methods are used to show how to determine the relevant distributions of kinetic parameters consistent with the measured data. 相似文献
12.
海相烃源岩二次生烃潜力定量评价新方法 总被引：1，自引：0，他引：1
烃源岩二次生烃的演化过程是残余干酪根热解演化与残留油热裂解转化两个既相互联系又完全不同的物理化学反应过程的叠加。本文利用自制高压釜热压生烃模拟实验装置,采取分阶段连续递进模拟实验方式,以海相烃源岩样品为例分别评价了残余干酪根的生烃潜力与残留可溶有机质转化油气潜力,建立了一套不同起始与终止成熟度海相烃源岩二次生烃潜力的定量评价方法,并首次明确提出了干酪根生油指数KIo、干酪根生气指数KIg、干酪根生烃指数KIh等评价烃源岩生烃潜力的参数,弥补了ROCK EVAL热解评价方法无法分别评价烃源岩在不同生烃演化阶段所生成的“油”或“烃气”潜力的不足。 相似文献
13.
M.H. Engel J. Rafalska-Bloch C.F. Schiefelbein J.E. Zumberge A. Serban 《Organic Geochemistry》1986,10(4-6)
Amino acids and sugars are principal constituents of marine organisms. The condensation of amino acids and sugars is one possible nonenzymatic, early diagenetic pathway for the incorporation of these compounds into more complex geopolymers. In this study, aqueous solutions consisting of l-lysine, l-histidine, l-arginine and d-(+)-glucose were heated (100°C) for up to 288 h. Portions of the melanoidin polymer isolated after heating were reheated in the presence of water (hydrous pyrolysis) for 72 h at 325°C. Reaction products were identified by GC and GC/MS. Stable isotopic (δ13C) and elemental analyses were used to follow thermal evolution.While the initial melanoidin was synthesized from a simple, four component system, the products generated during hydrous pyrolysis are of considerable complexity, and include straightchain and branched alkanes, alkadienes, alkynes, indole, dimethyl indane, ethyl phenol, quinoline, and xylenes, in addition to a multitude of as yet, unidentified components. Stable carbon isotopic values for the reactants and products correspond to trends observed for naturally generated geopolymers and light gases. Elemental analyses of the melanoidin prior and subsequent to hydrous pyrolysis indicate a kerogen evolution pathway similar to that observed for natural samples. Considering the intractable nature of kerogen, laboratory simulation studies of simple systems can provide an alternative approach for elucidating the origins of geopolymers and their potential for hydrocarbon generation. 相似文献
14.
15.
Anke Putschew Christine Schaeffer-Reiss Philippe Schaeffer Martin P Koopmans Jan W de Leeuw Michael D Lewan Jaap S Sinninghe Damsté James R Maxwell 《Organic Geochemistry》1998,29(8):1875-1890
An immature sulfur-rich marl from the Gessosso-solfifera Formation of the Vena del Gesso Basin (Messinian, Italy) has been subjected to hydrous pyrolysis (160 to 330°C) to simulate maturation under natural conditions. The kerogen of the unheated and heated samples was isolated and the hydrocarbons released by selective chemical degradation (Li/EtNH2 and HI/LiAlH4) were analysed to allow a study of the fate of sulfur- and oxygen-bound species with increasing temperature. The residues from the chemical treatments were also subjected to pyrolysis–GC to follow structural changes in the kerogens. In general, with increasing hydrous pyrolysis temperature, the amounts of sulfide- and ether-bound components in the kerogen decreased significantly. At the temperature at which the generation of expelled oil began (260°C), almost all of the bound components initially present in the unheated sample were released from the kerogen. Comparison with an earlier study of the extractable organic matter using a similar approach and the same samples provides molecular evidence that, with increasing maturation, solvent-soluble macromolecular material was initially released from the kerogen, notably as a result of thermal cleavage of weak carbon–heteroatom bonds (sulfide, ester, ether) even at temperatures as low as 220°C. This solvent-soluble macromolecular material then underwent thermal cleavage to generate hydrocarbons at higher temperatures. This early generation of bitumen may explain the presence of unusually high amounts of extractable organic matter of macromolecular nature in very immature S-rich sediments. 相似文献
16.
二次生烃迟滞性定量评价方法及其在渤海湾盆地中的应用 总被引：22，自引：2，他引：22
中国叠合盆地古生界烃源岩具有多次埋藏、异常受热、多次生烃和多次成藏的特点。不同成熟度、不同母质类型样品热解和高压釜模拟实验反映烃源岩的二次生烃不遵循Tissot经典的连续生烃演化模式,具有显著的迟滞效应,这种迟滞程度与烃源岩二次生烃时的原始成熟度有关,当Ro 等于 0.9%左右时迟滞性最小。究其原因受化学动力学机制控制,二次生烃反应活化能的分布体现了一次生烃受热降解形成的中间产物在一次演化中止前未能有效释放而部分聚集在干酪根内的特性以及化学结构在冷却后的高度固化,导致二次增温初期中间产物的快速释放和化学结构再次活化的惰性,从而使得二次生烃显现出脉冲式的非连续演化过程。基于二次生烃迟滞性量版,结合渤海湾盆地具体地质条件,从生烃史和生烃阶段组合的关键要素入手,采用关键要素递阶优选原则,依次通过对显著生烃深度、生烃率等要素的递阶分析,确定了渤海湾盆地二次生烃有利区. 相似文献
17.
A least-squares inverse method is applied to the estimation of optimum kinetic parameters with statistical error bounds from concentration data obtained in isothermal hydrous pyrolysis experiments. The inverse method requires the specification of a data-parameter relationship (e.g., classical kinetic theory), the prior covariance matrices of data and parameter errors, as well as the prior central estimates of data and parameters. The reaction scheme considered is the common case of kerogen breakdown by Gaussian-weighted independent parallel first-order reactions and bitumen cracking by a single first-order reaction. The nonlinearity of the problem is reduced by a logarithmic transformation, which suggests a parameterization in terms of logarithmic concentrations, activation energies, and logarithmic Arrhenius factors. The linearized variance analysis is valid for the case studied, and the posterior covariance matrix reveals which parameters are constrained by the data. We find that the statistical errors in the average activation energy and the associated Arrhenius factor are strongly correlated. Hence, the parameters which determine the temperature dependence of the reaction rate have not been resolved independently. Furthermore, the kinetic results are very sensitive to the presence of a distribution of activation energies in kerogen breakdown. This distribution is not constrained by the data. As a consequence, neglecting the consideration of distributions of activation energies results in activation parameter values which are much too low. This is the major reason for the commonly encountered discrepancy between kinetic parameter values obtained from hydrous pyrolysis and micropyrolysis experiments, respectively. 相似文献
18.
加水热模拟中深湖与煤系泥岩地化特征比较 总被引：2，自引：0，他引：2
通过深湖泥岩和煤系泥岩的加水热模拟研究认为,在热模拟实验过程中,深湖泥岩和煤系泥岩显示不同特征,并且其演化有差别。深湖泥岩利于液态原油的生成,并且转化率高于煤系泥岩。深湖泥岩残余可溶有机质饱和烃含量高于煤系泥岩,非烃含量则低于煤系泥岩。深湖泥岩胶质 /沥青质和饱芳比均随温度升高而降低,而煤系泥岩的胶质 /沥青质随温度升高有增加趋势,其饱芳比的变化则不大或有降低趋势。深湖泥岩的Tmax难以指示演化阶段,其干酪根碳同位素值明显轻于煤系泥岩,它们的值均随温度的升高而变重。 相似文献
19.
Hydrous pyrolysis experiments at 200 to 365°C were carried out on a thermally immature organic-rich limestone containing Type-IIS kerogen from the Ghareb Limestone in North Negev, Israel. This work focuses on the thermal behavior of both organic and inorganic sulfur species and the partitioning of their stable sulfur isotopes among organic and inorganic phases generated during hydrous pyrolyses. Most of the sulfur in the rock (85%) is organic sulfur. The most dominant sulfur transformation is cleavage of organic-bound sulfur to form H2S(gas). Up to 70% of this organic sulfur is released as H2S(gas) that is isotopically lighter than the sulfur in the kerogen. Organic sulfur is enriched by up to 2‰ in 34S during thermal maturation compared with the initial δ34S values. The δ34S values of the three main organic fractions (kerogen, bitumen and expelled oil) are within 1‰ of one another. No thermochemical sulfate reduction or sulfate formation was observed during the experiments. The early released sulfur reacted with available iron to form secondary pyrite and is the most 34S depleted phase, which is 21‰ lighter than the bulk organic sulfur. The large isotopic fractionation for the early formed H2S is a result of the system not being in equilibrium. As partial pressure of H2S(gas) increases, retro reactions with the organic sulfur in the closed system may cause isotope exchange and isotopic homogenization. Part of the δ34S-enriched secondary pyrite decomposes above 300°C resulting in a corresponding decrease in the δ34S of the remaining pyrite. These results are relevant to interpreting thermal maturation processes and their effect on kerogen-oil-H2S-pyrite correlations. In particular, the use of pyrite-kerogen δ34S relations in reconstructing diagenetic conditions of thermally mature rocks is questionable because formation of secondary pyrite during thermal maturation can mask the isotopic signature and quantity of the original diagenetic pyrite. The main transformations of kerogen to bitumen and bitumen to oil can be recorded by using both sulfur content and δ34S of each phase including the H2S(gas). H2S generated in association with oil should be isotopically lighter or similar to oil. It is concluded that small isotopic differentiation obtained between organic and inorganic sulfur species suggests closed-system conditions. Conversely, open-system conditions may cause significant isotopic discrimination between the oil and its source kerogen. The magnitude of this discrimination is suggested to be highly dependent on the availability of iron in a source rock resulting in secondary formation of pyrite. 相似文献
20.
密闭体系与开放体系模拟实验结果的比较研究及其意义 总被引：3，自引：0，他引：3
利用广泛应用的高压釜和Rock Eval热解实验技术，对松辽盆地3个有机质样品同时进行了密闭条件下的加水恒温热解实验和开放条件下的恒速升温热解实验。利用后一实验数据所标定得到的化学动力学模型计算了与高压釜相同实验条件下的有机质产油、产气率。结果表明，在线计量的恒速升温Rock Eval实验方法由于不损失C6—C13的轻质烃组分，在计量液态油的产量方面较需要抽提、恒重的高压釜实验方法更为准确。因此为解决热模拟实验中难以计量、但对成烃评价有重要意义的C6—C13组分的计量问题提供了一条有效的途经。这可能也表明，先由实验数据建立有关的化学动力学模型，之后由它来进一步计算有机质的成烃率，不仅是可行的，而且应该更为准确。 相似文献