首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 62 毫秒
1.
西藏扎北盐湖秋季卤水(硫酸钠亚型)5℃等温蒸发实验研究   总被引:2,自引:0,他引:2  
西藏扎北盐湖硫酸钠亚型卤水中富含元素Li、B、K和微量元素Rb、Cs等.为了更好地了解卤水在自然条件下的蒸发结晶规律,需对相应卤水进行低温室内等温蒸发实验研究.本文对该盐湖卤水进行了5℃等温蒸发试验,并利用Na+、K+、Mg2+//Cl-、SO42--H2O五元水盐体系0℃相图,构筑了从干基立体图Na2SO4角顶的放射...  相似文献   

2.
彭芸  曾英  于旭东  张龙钦  吴祎  冯珊 《地质学报》2010,84(11):1697-1703
针对西藏扎布耶盐湖卤水组成,采用等温蒸发法分别研究了含钾四元体系Na+,K+//Cl-,B4O27--H2O308.15K、五元体系K+//Cl-,CO23-,SO42-,B4O72--H2O273.15K下的介稳相关系。分别测定了上述体系308.15K、273.15K时介稳平衡液相组成及密度、pH值。根据实验数据绘制了相应的介稳相图、水图。结果表明,本文研究的两个体系均为简单共饱型,无复盐和固溶体生成。其中,四元体系介稳相图由2个共饱点,5条单变量曲线,4个结晶区组成。平衡固相分别为Na2B4O7.10H2O、K2B4O7.4H2O、NaCl和KCl。对比四元体系308.15K和273.15K下的介稳相图发现,平衡固相盐的种类及结晶形式均没有发生变化,但结晶区大小产生变化:在308.15K下,Na2B4O7.10H2O结晶区变小,K2B4O7.4H2O结晶区变大。五元体系投影图中有1个共饱点、3条单变量曲线和3个结晶相区。结晶相区分别为K2CO3.3/2H2O、K2SO4和KCl。K2CO3.3/2H2O结晶区面积最小,K2SO4结晶区面积最大。K2CO3对KCl有较强的盐析作用。  相似文献   

3.
硫酸钠亚型富锂卤水25℃等温蒸发过程的计算机模拟   总被引:5,自引:0,他引:5  
卜令忠  乜贞  宋彭生 《地质学报》2010,84(11):1708-1714
我国青藏高原上分布有许多盐湖,其中扎布耶等碳酸盐型盐湖、东台吉乃尔等硫酸镁亚型盐湖是著名的富锂盐湖,已成功开发生产出碳酸锂产品。青藏高原上还有许多硫酸钠亚型盐湖,其卤水锂浓度高,钾、镁、硼等有用成分丰富。针对这些盐湖资源,目前尚未进行开发利用研究。这些卤水的等温蒸发实验研究,是必不可少的关键工作之一。本文使用我们由Pitzer电解质溶液理论建立的Li+,Na+,K+,Mg2+/Cl-,SO24--H2O体系的热力学模型,对25℃下几种硫酸钠亚型富锂卤水等温蒸发过程进行了计算机模拟,预测蒸发过程中盐类矿物的析出顺序、卤水组成变化规律、钠、钾、镁、锂盐的饱和点,并在此基础上进行卤水蒸发过程物料平衡关系的理论计算等。本文对西藏3种硫酸钠亚型卤水和国外2种硫酸钠亚型卤水25℃等温蒸发过程进行了模拟。其析盐顺序的特点是:在第一个矿物石盐饱和析出后,接着析出的含钾矿物是钾芒硝,而不是钾镁矾类矿物。其后钾盐则会以钾岩盐形式析出。锂盐饱和后则主要以复盐Li2SO4.K2SO4形式析出。美国银峰卤水的模拟结果与实验蒸发过程完全一致,并给出其继续蒸发时的析盐状况。另4种硫酸钠亚型卤水的模拟结果不仅可以作为未来实验研究的基本参考和注意点,同样也可作为其盐田设计和工艺安排的基本理论依据。本文研究为该类型卤水资源综合开发利用工艺路线的确立提供理论参考。  相似文献   

4.
采用等温蒸发法研究简单四元体系Na ∥Cl-,CO32-,B4O72--H2O273K时的介稳相平衡,并测定该体系273K平衡液相中各组分的溶解度及密度,该体系的介稳相图和密度组成图显示:该四元体系在273K时的相图由3条溶解度单变量线、3个结晶区及1个共饱和点组成。体系属简单共饱型,无复盐或固溶体形成,3个结晶区分别对应单盐Na2CO3·10H2O,NaCl和Na2B4O7·10H2O。共饱点E处于Na2CO3·10H2O,NaCl及Na2B4O7·10H2O3盐共饱和,所对应的平衡液相组成为w(Na2CO3)=6.81%,w(NaCl)=21.69%,w(Na2B4O7)=0.65%,w(H2O)=70.85%。研究体系在273K下,Na2CO3·10H2O是碳酸钠盐的唯一析出形式,且硼酸钠对碳酸钠有盐析作用。  相似文献   

5.
西藏当雄错盐湖卤水冬季日晒蒸发实验研究   总被引:7,自引:0,他引:7  
伍倩  郑绵平  乜贞  卜令忠 《地质学报》2013,87(3):433-440
西藏当雄错盐湖位于藏北高原腹地西南侧,其水化学类型属典型的中度碳酸盐型,具有很好的工业开发前景和价值.自然蒸发是盐田日晒工艺的应用基础工作,本文基于室内卤水等温蒸发实验的相关结果,在当雄错湖区现场开展了盐湖卤水冬季日晒蒸发实验,通过考察碳酸盐型盐湖卤水在现场低温条件下自然蒸发过程中液相各元素的富集规律以及矿物的结晶析盐规律,分析了锂、硼、钾等元素的集散行为,并根据卤水蒸发过程中的元素富集、蒸失水量、盐类析出顺序、矿物组合以及物化性质的变化探索了盐类分离的控制条件.以Na+,K+/CO2-3,SO2-4,Cl--H2O五元体系(25℃)介稳相图为参考依据,绘制了当雄错盐湖卤水冬季日晒蒸发的结晶析盐路线.实验结果表明,当雄错盐湖卤水在冬季日晒蒸发过程中依次析出石盐、泡碱、天然碱、硼砂、钾石盐和扎布耶石,另有少量芒硝和泡碱等低温产物会提前析出或被母液夹带析出,利用冬季低温蒸发可制取富锂卤水,蒸发后期的母卤还可用于提取硼砂和钾石盐等矿物资源.实验结果为下一步开展盐田工程设计及制卤工艺操作提供了必要的基础数据,同时也为碳酸盐型盐湖卤水的综合利用和开发提供了理论支持.  相似文献   

6.
桑世华  李明  李恒  孙明亮 《地质学报》2010,84(11):1704-1707
采用等温溶解平衡法研究了288K时Li+, Mg2+//SO2-4, B4O2-7- H2O四元体系的固液相平衡关系,测定了该四元体系在288K时平衡液相的溶解度和密度。依据实验测定的平衡溶解度数据及对应的平衡固相,绘制了该四元体系的平衡相图及密度组成图。研究结果表明:交互四元体系Li+, Mg2+//SO2-4, B4O2-7- H2O 288K时平衡相图中有2个共饱点,5条单变量曲线,4个结晶区对应的平衡固相分别为Li2B4O7·3H2O,Li2SO4·H2O,MgB4O7·9H2O和MgSO4·7H2O。  相似文献   

7.
采用等温溶解平衡法研究了288K时Li+, Mg2+//SO2-4, B4O2-7- H2O四元体系的固液相平衡关系,测定了该四元体系在288K时平衡液相的溶解度和密度.依据实验测定的平衡溶解度数据及对应的平衡固相,绘制了该四元体系的平衡相图及密度组成图.研究结果表明:交互四元体系Li+, Mg2+//SO2-4, B4O2-7- H2O 288K时平衡相图中有2个共饱点,5条单变量曲线,4个结晶区对应的平衡固相分别为Li2B4O7·3H2O,Li2SO4·H2O,MgB4O7·9H2O和MgSO4·7H2O.  相似文献   

8.
采用等温溶解平衡法研究了288K时Li+,Mg2+//SO42-,B4O72--H2O四元体系的固液相平衡关系,测定了该四元体系在288K时平衡液相的溶解度和密度。依据实验测定的平衡溶解度数据及对应的平衡固相,绘制了该四元体系的平衡相图及密度组成图。研究结果表明:交互四元体系Li+,Mg2+//SO42-,B4O27--H2O288K时平衡相图中有2个共饱点,5条单变量曲线,4个结晶区对应的平衡固相分别为Li2B4O7.3H2O,Li2SO4.H2O,MgB4O7.9H2O和MgSO4.7H2O。  相似文献   

9.
采用等温蒸发法研究简单四元体系Na+//CI-,CO32-,B4O72---H2O 273 K时的介稳相平衡,并测定该体系273 K平衡液相中各组分的溶解度及密度,该体系的介稳相图和密度组成图显示:该四元体系在273 K时的相图由3条溶解度单变量线、3个结晶区及1个共饱和点组成.体系属简单共饱型,无复盐或固溶体形成,3个结晶区分别对应单盐Na2CO3?10H2O,NaCI和Na2B4O7?10H2O.共饱点E处于Na2CO3?10H2O,NaCI及Na2B4O,?10H2O3盐共饱和,所对应的平衡液相组成为ω(Na2CO3)=6.81%,ω(NaCl)=21.69%,ω(Na2B4O7)=0.65%.ω(H20)=70.85%.研究体系在273 K下,Na2CO3?10H2O是碳酸钠盐的唯一析出形式,且硼酸钠对碳酸钠有盐析作用.  相似文献   

10.
<正> 巴里坤盐湖位于天山北侧,是固液二相并存的现代盐湖矿床。上部为深20~80cm 的液体卤水(夏季),湖水浓度20°Be′①左右。下部为一层60~200cm 左右的固体芒硝矿体。夏季卤水化学组成(据D0026样,单位:g/L)为:NaCl.54.11,Na_2SO4 106.6,MgCl_231.507,KCl 2.16,CaSO_4 1.11,Mg(HCO_3)_2 0.83,CaCO_3 0.187。巴里坤盆地冬季寒冷,夏季最高气温可达30℃以上,日照时间长,蒸发量远大于降水量。现以Na~+,Mg~2+,Cl~-,SO_4~2—H_2O 四元体系相图(图1)为基础,以25℃,-5℃分别代表夏季,秋末初冬湖水平均水温。由这二种温度条件下卤水等温蒸发、结晶的相图变化为典  相似文献   

11.
Komatiites are mantle-derived ultramafic volcanic rocks. Komatiites have been discovered in several States of India, notably in Karnataka. Studies on the distribution of trace-elements in the komatiites of India are very few. This paper proposes a simple, accurate, precise, rapid, and non-destructive wavelength-dispersive x-ray fluorescence (WDXRF) spectrometric technique for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in komatiites, and discusses the accuracy, precision, limits of detection, x-ray spectral-line interferences, inter-element effects, speed, advantages, and limitations of the technique. The accuracy of the technique is excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Zr, Nb, Ba, Pb, and Th and very good (within 4%) for Y. The precision is also excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th. The limits of detection are: 1 ppm for Sc and V; 2 ppm for Cr, Co, and Ni; 3 ppm for Cu, Zn, Rb, and Sr; 4 ppm for Y and Zr; 6 ppm for Nb; 10 ppm for Ba; 13 ppm for Pb; and 14 ppm for Th. The time taken for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in a batch of 24 samples of komatiites, for a replication of four analyses per sample, by one operator, using a manual WDXRF spectrometer, is only 60 hours.  相似文献   

12.
This paper reports the first results of a study of 11 isotope systems (3He/4He, 40Ar/36Ar, 34S/32S, 65Cu/63Cu, 62Ni/60Ni, 87Sr/86Sr, 143Nd/144Nd, 206–208Pb/204Pb, Hf–Nd, U–Pb, and Re–Os) in the rocks and ores of the Cu–Ni–PGE deposits of the Norilsk ore district. Almost all the results were obtained at the Center of Isotopic Research of the Karpinskii All-Russia Research Institute of Geology. The use of a number of independent genetic isotopic signatures and comprehensive isotopic knowledge provided a methodic basis for the interpretation of approximately 5000 isotopic analyses of various elements. The presence of materials from two sources, crust and mantle, was detected in the composition of the rocks and ores. The contribution of the crustal source is especially significant in the paleofluids (gas–liquid microinclusions) of the ore-forming medium. Crustal solutions were probably a transport medium during ore formation. Air argon is dominant in the ores, which indicates a connection between the paleofluids and the atmosphere. This suggests intense groundwater circulation during the crystallization of ore minerals. The age of the rocks and ores of the Norilsk deposits was determined. The stage of orebody formation is restricted to a narrow age interval of 250 ± 10 Ma. An isotopic criterion was proposed for the ore-bearing potential of mafic intrusions in the Norilsk–Taimyr region. It includes several interrelated isotopic ratios of various elements: He, Ar, S, and others.  相似文献   

13.
最新的流行病学研究表明,空气中较高浓度的悬浮细颗粒可能对人类的健康有不利的影响。根据该项研究显示,由于心脏病、慢性呼吸问题和肺功能指标恶化而导致死亡率的升高与细尘粒子有关。这些研究结果已经促使欧盟于1999年4月出台了限制空气中二氧化硫、二氧化氮、氧化氮、铅和颗粒物含量的法案(1999/30/EC),对各项指标包括对可吸入PM10颗粒的浓度提出了新的限制性指标。PM10颗粒是指可以通过预分级器分离采集的气体动力学直径小于10μm的细颗粒。目前研究的兴趣重点逐步偏向PM2.5这些更细微颗粒物,PM2.5这种颗粒物对健康有明显的不利影响。在欧盟指令2008/50/EC中,对PM10和PM2.5都提  相似文献   

14.
本文介绍样品经四硼酸锂熔融制成玻璃小饼。采用Lachance模式和理论a系数来校正元素间的效应,由3080E型X-射线荧光谱仪和DF-350B数据处理系统完成硅酸盐中十三个项目的测定。  相似文献   

15.
本文拟定了一种以熔融法制备样片,用X射线荧光光谱测定硅酸盐类样品中Si、Fe、Al、Tj、Mn、Ca、Mg、K、Na、P等元素的分析方法。在对不同靶材X光管和分光晶体实验对比的基础上,选择了最佳的测量条件。该法具有快速、准确,测量范围广,检测限低,价格便宜等优点。经过近百个各种类型标样或管理样品的分析对比表明,本法不仅适用于硅酸盐类岩石样品的分析,还适用于铁矿、铝土矿、碳酸盐类岩矿样品以及水泥、耐火材料等样品的分析。  相似文献   

16.
17.
Mining induced subsidence can significantly affect mining costs where major surface facilities and natural environment need to be protected. Overburden grout injection is a technology used to control coal mine subsidence by injecting the mine waste material extracted from the coal back into the inter-burden rock during longwall mining. The flowing slurry is here categorised as a nonlinear viscous cohesive (Bingham plastic) fluid. During longwall mining the grout slurry is pumped into the separated beds of the rock mass through a central vertical borehole, which is drilled deep into the inter-burden rock strata above the coal seam. However, a blockage can occur in the injection system when the slurry velocity falls below a certain critical threshold velocity, indicating a material phase change from cohesive-viscous to cohesive-frictional. In situ field injection tests through boreholes have been simulated at a smaller scale at the CSIRO laboratory in Brisbane by pumping the slurry through a radial disk (gap = 4 mm) from its centre. Laboratory experiments indicate a general, nonlinear, cohesive, viscous, frictional model for shear behaviour of the slurry, in which the material shear parameters are functions of the disk radial distance. Complete dimensional and dimensionless analytical solutions have been developed based on an approach related to Bingham–Herschel–Bulkley fluid mechanics. The derived formulae include relations for minimum pump pressure, local pressure and pressure gradient, wall shear stress, volume rate, velocity and velocity gradient. The theoretical results match the experimental measurements. The experiments covered slurries with maximum particle sizes of 0.5 to 2 mm with about 50% being larger than 100 µm. The viscosities at the various solids concentrations were measured with a standard torsion viscometer. This study differs from the previous research in several distinct aspects, namely, consideration of the variable shear parameters rather than fixed values, inclusion of total nonlinear behaviour, and implementation of a friction function to mimic behaviour of the deposited and consolidating stiff slurry, which can cause a significant pressure rise as a result of the increased shear resistance.  相似文献   

18.
《Applied Geochemistry》2001,16(2):137-159
Five hundred and ninety-eight samples of terrestrial moss (Hylocomium splendens and Pleurozium schreberi) collected from a 188,000 km2 area of the central Barents region (NE Norway, N Finland, NW Russia) were analysed by ICP-AES and ICP-MS. Analytical results for Al, B, Ba, Ca, K, La, Mg, Mn, Na, P, Rb, Si, Sr, Th, U and Y concentrations are reported here. Graphical methods of data analysis, such as geochemical maps, cumulative frequency diagrams, boxplots and scatterplots, are used to interpret the origin of the patterns for these elements. None of the elements reported here are emitted in significant amounts from the smelting industry on the Kola Peninsula. Despite the conventional view that moss chemistry reflects atmospheric element input, the nature of the underlying mineral substrate (regolith or bedrock) is found to have a considerable influence on moss composition for several elements. This influence of the chemistry of the mineral substrate can take place in a variety of ways. (1) It can be completely natural, reflecting the ability of higher plants to take up elements from deep soil horizons and shed them with litterfall onto the surface. (2) It can result from naturally increased soil dust input where vegetation is scarce due to harsh climatic conditions for instance. Alternatively, substrate influence can be enhanced by human activity, such as open-cast mining, creation of ‘technogenic deserts’, or handling, transport and storage of ore and ore products, all of which magnify the natural elemental flux from bedrock to ground vegetation. Seaspray is another natural process affecting moss composition in the area (Mg, Na), and this is most visible in the Norwegian part of the study area. Presence or absence of some plant species, e.g., lichens, seems to influence moss chemistry. This is shown by the low concentrations of B or K in moss on the Finnish and Norwegian side of the (fenced) border with Russia, contrasting with high concentrations on the other side (intensive reindeer husbandry west of the border has selectively depleted the lichen population).  相似文献   

19.
We have developed a set of four synthetic standards for the rare earth and high field strength elements designed for use in the determination of those elements in silicates. The base material is a glass nominally at the eutectic of the MgO-Al2O3-SiO2 ternary system. The nominal doping level was 2 wt% of the elements as oxides. To avoid problems associated with peak interference, the elements were doped in four separate glasses.  相似文献   

20.
Bellechester, Minnesota, is a small community of approximately 155 residents located on the county line between Goodhue and Wabasha counties in southeast Minnesota's karst region. Bellechester is served by a 21-year-old wastewater treatment facility (WWTF) consisting of three waste-stabilization ponds. On 28 April 1992 six sinkholes were discovered to have drained cell 2 of the WWTF resulting in the loss of approximately 8.7×106 1 of partially treated effluent and about 600 m3 of soil into previously undetected subsurface voids of unknown dimensions. In the week following the collapse, approximately 200 water wells located within a 5-km radius of the WWTF were sampled in an after-the-fact, emergency sampling program. Twelve samples with elevated fecal coliform levels, 18 samples with nitrate-nitrogen greater than the 10 mg/1 standard, and no samples with elevated chlorides were found. However, the elevated levels could not be unambiguously attributed to the WWTF collapse. This is the third WWTF to fail by sinkhole collapse in southeast Minnesota since 1974. All three collapsed lagoons have been located in similar geomorphic and stratigraphic settings. However, at least two lagoons have collapsed in the adjacent area in northeast Iowa, and these lagoons are located at different stratigraphic positions. Twenty-two WWTFs constructed in southeast Minnesota's karst region in the last 25 years have been identified as subject to potential sinkhole collapse. An unknown but significant number of manure storage lagoons, flood control structures, etc., have also been constructed in the karst region and are at risk. Public agencies are beginning to develop plans to deal with the risk associated with existing and future waste lagoons in this environment. The critical hydrogeologic parameters that can be used to prioritize the risk of collapse at existing facilities include: (1) the lithology of the first bedrock beneath each lagoon, (2) the thickness of surficial materials between the lagoon and the bedrock surface, (3) the presence and construction of liners (seepage rate), and (4) the proximity to existing sinkholes.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号