With increasing demands for coal resources, coal has been gradually mined in deep coal seams. Due to high gas content, pressure and in situ stress, deep coal seams show great risks of coal and gas outburst. Protective coal seam mining, as a safe and effective method for gas control, has been widely used in major coal-producing countries in the world. However, at present, the relevant problems, such as gas seepage characteristics and optimization of gas drainage borehole layout in protective coal seam mining have been rarely studied. Firstly, by combining with formulas for measuring and testing permeability of coal and rock mass in different stress regimes and failure modes in the laboratory, this study investigated stress–seepage coupling laws by using built-in language Fish of numerical simulation software FLAC3D. In addition, this research analyzed distribution characteristics of permeability in a protected coal seam in the process of protective coal seam mining. Secondly, the protected coal seam was divided into a zone with initial permeability, a zone with decreasing permeability, and permeability increasing zones 1 and 2 according to the changes of permeability. In these zones, permeability rises the most in the permeability increasing zone 2. Moreover, by taking Shaqu Coal Mine, Shanxi Province, China as an example, layout of gas drainage boreholes in the protected coal seam was optimized based on the above permeability-based zoning. Finally, numerical simulation and field application showed that gas drainage volume and concentration rise significantly after optimizing borehole layout. Therefore, when gas is drained through boreholes crossing coal seams during the protective coal seam mining in other coal mines, optimization of borehole layout in Shaqu Coal Mine has certain reference values.
相似文献Since most coalfields in China are commonly characterized by high gas content and low permeability, there is an urgent need to improve coal seam permeability and further enhance coal bed methane (CBM) extraction efficiency. As an emerging fracturing technology, the CO2 gas fracturing (CGF) technology has been widely used because of its advantages of low cost, environmental protection and high fragmentation efficiency. In order to improve the fracturing ability of CGF technique and optimize the release orifices of discharge head, computational fluid dynamics model was used in this paper to simulate the flow fields of dynamic pressure of gas jet released from the orifices with different structures and other geometrical parameters. The results show that the orifice structure has a great influence on the flow field of gas jet, but little influence on the magnitude of the dynamic pressure. Besides, the maximum dynamic pressure of gas jet linearly decreases with the increase in the number of release orifices. Based on a series of simulation results, the discharge head which has single group of orifices with structure c, diameter of 24 mm can be identified as the best choice for fieldwork. Then, two field experiments were conducted in Pingdingshan and Changping coal mines to evaluate the enhanced CBM extraction efficiency by CGF. The results indicate that the CGF can effectively create a large number of cracks in a large range around the fracturing borehole in the coal seam and further significantly improve the permeability. And the CBM extraction efficiency can be improved to a higher level from a lower level and maintained for a long time. Besides, the effective influence radii caused by CGF in Pingdingshan and Changping coal mines are 15.19 m and 12.5 m, respectively. Compared with other fracturing techniques, the CGF technique has a promising application prospect.
相似文献The factors affecting permeability change under repeated mining of coal seams are important study aspects that need to be explored. This study combined various stress variation characteristics of protective seam mining and simplified the stress path of repeated mining in protective seam mines. Based on the results from the bespoke gas flow and displacement testing apparatus, seepage tests for simulated repetitive mining were carried out. The results simulated the actual behavior very well. With any drastic increase in the mining influence, the axial deviation stress in the stress path increased, and the greater the difference in coal permeability during the unloading and stress recovery stage, the more substantial the increase in permeability. The change in coal permeability was significantly influenced by the severity of simulated repeated mining cycles. When the mining stress exceeded a critical value, the permeability of the coal sample increased with the increase in the number of loading and unloading cycles, but the reverse was true when the mining stress was lower than the critical value. The effective sensitivity of seepage to the applied stress decreased with an increase in the number of stress cycles. With a decrease in the deviation stress, that is, with lower severity of mining influence, the effective sensitivity of coal seepage to stress gradually decreased.
相似文献Pseudo-reservoir stimulation in horizontal well is an effective technique for indirectly extracting coalbed methane (CBM) in soft coal from the surrounding rocks (pseudo-reservoir). However, systematic studies of the theory and on-site application of this technique are still lacking, which severely hinders its application. In this paper, the technical principles of pseudo-reservoir stimulation are analyzed firstly, and then, the technical advantages are demonstrated by experimental tests and theoretical analysis. The results show that the pseudo-reservoir generally possesses considerable gas adsorption capacity, with the gas content of 1.56–4.22 cm3/g (avg. 2.51 cm3/g) in Well XC-01, which can be extracted as supplementary resources. The fracability of the pseudo-reservoirs is 0.73–0.92, which is much higher than that of the coal seam, i.e., 0.03–0.43. Meanwhile, the compressive and tensile strength and cohesion of the pseudo-reservoir are higher than those of the coal seam, indicating pseudo-reservoir stimulation is more conducive to forming fracture network, and maintaining wellbore stability and fracture conductivity. The technical feasibility of pseudo-reservoir stimulation is determined by the regional geological conditions, showing simple tectonic conditions and well-developed surrounding rocks with high fracability and mechanical strength but low permeability, water sensitivity and water content are beneficial for the technique application. Note that the fracture conductivity in pseudo-reservoir is more stable and higher than that in coal seam, pseudo-reservoir stimulation is beneficial for the CBM extraction from both hard and soft coal seams. By minimizing the gas diffusion distance, this technique overcomes the technical obstacles to the CBM commercialized production in soft coal.
相似文献In situ stress is not only a vital indicator for selecting explorative regions of coalbed methane (CBM), but also a pivotal factor affecting CBM production. The present study explored whether in situ stress affected the development potential of CBM in western Guizhou, China. To this end, we collected injection/falloff well test data and gas content data from 70 coal seams in 28 wells. The study found that from top to bottom, strike slip fault stress fields (<?500 m), normal fault stress fields (500–1000 m) and strike slip fault stress fields (>?1000 m) were successively developed in western Guizhou. The distribution features of vertical permeability in western Guizhou are consistent with the stress fields' transformation location. The coal permeability in the western part in Guizhou presents a tendency of increase followed by decrease as a result of increased burial depth. The vertical development characteristics of coal seam gas content are controlled mainly by reservoir pressure, and the relationship between reservoir pressure and buried depth shows a linear increase. The CBM in western Guizhou is divided vertically into three development potential regions dependent on the characteristics of burial depth, permeability and gas content of coal seams. The most favorable vertical development potential region in western Guizhou is 500–1000 m. This region exhibits high gas content, high permeability and moderate burial depth, which are favorable for the production of CBM. These research results can provide basis for geological selection and engineering implementation of CBM in western Guizhou.
相似文献Auger mining (AM) is an effective and safe way to excavate an extremely thin protective layer. This method can relieve pressure and enhance the permeability of an ultra-contiguous coal layer with high gas capacity. However, there have been few studies on AM. Based on the conditions of a coal mine in Shanxi Province, China, theoretical analyses, laboratory tests and numerical simulations were used to analyze the evolution law of the overburden permeability in an AM face. A stress–damage–permeability coupling model was proposed, and a numerical simulation algorithm for fluid–solid coupling with FLAC software was established. Through this method, the evolution law of stress and permeability and its influencing factors of the overburden of the AM face were found. The intermediate coal pillar (ICP) width and the AM height and length are the main factors influencing the permeability evolution of the AM face. The first factor determines the damage state of the ICP in the goaf, and the last two factors influence the zone size with permeability enhancement of the protected layer. Therefore, reasonable AM parameter design is the key to both safe mining operations in the AM face and pressure relief and permeability enhancement.
相似文献Methane content in coal seam is an essential parameter for the assessment of coalbed gas reserves and is a threat to underground coal mining activities. Compared with the adsorption-isotherm-based indirect method, the direct method by sampling methane-bearing coal seams is apparently more accurate for predicting coalbed methane content. However, the traditional sampling method by using an opened sample tube or collecting drill cuttings with air drilling operation would lead to serious loss of coalbed methane in the sampling process. The pressurized sampling method by employing mechanical-valve-based pressure corer is expected to reduce the loss of coalbed methane, whereas it usually results in failure due to the wear of the mechanical valve. Sampling of methane-bearing coal seams by freezing was proposed in this study, and the coalbed gas desorption characteristics under freezing temperature were studied to verify the feasibility of this method. Results show that low temperature does not only improve the adsorption velocity of the coalbed gas, but also extend the adsorption process and increase the total adsorbed gas. The total adsorbed methane gas increased linearly with decreasing temperature, which was considered to be attributed to the decreased Gibbs free energy and molecular average free path of the coalbed gas molecular caused by low temperature. In contrast, the desorption velocity and total desorbed gas are significantly deceased under lower temperatures. The process of desorption can be divided into three phases. Desorption velocity decreases linearly at the first phase, and then, it shows a slow decreases at the second phase. Finally, the velocity of desorption levels off to a constant value at the third phase. The desorbed coalbed gas shows a parabolic relation to temperature at each phase, and it increases with increasing temperature at the first phase, and then, it poses a declining trend with increasing temperature at the rest phases. The experimental results show that decreasing the system temperature can restrain desorption of coalbed methane effectively, and it is proven to be a feasible way of sampling methane-bearing coal seams.
相似文献Bituminous coal in the Xutuan Coal Mine of the Huaibei Mining Bureau (China) is the research object of this study. The influence of moisture content on the porosity of the bituminous coal was investigated from a microscopic perspective by using a high-solution 3D X-ray micro-analyzer. The threshold segmentation method was used to segment the scanning slices of the coal samples. The threshold values of the various media were in the following order (from large to small): minerals, water, matrices, and fractures. The scanning volume and actual volume proportions of the different media in the coal samples with different moisture contents were calculated. The accuracy of the computerized tomography (CT) scanning method in measuring the coal moisture content was verified by comparison with the results obtained using the weighing method. 3D reconstructed coal samples, with different moisture contents, were analyzed, as well as separately reconstructed fractures and water in the coal samples with different moisture contents. The heterogeneity and anisotropy of the coal mass were explained quantitatively by the CT scanning intensity. A commonly used fracture classification method indicated that the primary fracture in the coal sample was a type A fracture. The results of the analysis of water in the coal fracture indicated that the porosity of bituminous coal decreased with the increase in moisture content in conditions of atmospheric pressure and a short immersion period. However, a certain level of porosity remained evident, and the degree of fracture development of the coal samples remained unchanged. This is attributed to the minor volumetric change in the minerals in the coal samples, as the water does not completely occupy the fractures in the coal samples, and the dissolution of the minerals by water is therefore not significant. The reasons for the moisture content affecting gas adsorption, seepage, and strength of a coal body were analyzed from a microscopic perspective. In addition, the types of fractures and water in the coal samples were classified by employing statistics and analyses of volume, surface area, specific surface area, and aspect ratio of the fractures and the water in the coal samples with different moisture contents.
相似文献Characterization of coal micro-structure and the associated rock mechanical properties are of key importance for coal seam exploration, coal bed methane development, enhanced coal bed methane production and CO2 storage in deep coal seams. Considerable knowledge exists about coal chemical properties, but less is known about the nanoscale to the micro-scale structure of coals and how they change with coal strength across coal ranks. Thus, in this study, 3D X-ray micro-computed tomography (with a voxel size of 3.43 µm) and nano-indentation tests were conducted on coal samples of different ranks from peat to anthracite. The micro-structure of peats showed a well-developed pore system with meso- and micro-pores. The meso-pores essentially disappear with increasing rank, whereas the micro-pores persist and then increase past the bituminous rank. The micro-fracture system develops past the peat stage and by sub-bituminous ranks and changes into larger and mature fracture systems at higher ranks. The nano-indentation modulus showed the increasing trend from low- to high-rank coal with a perfect linear relationship with vitrinite reflectance and is highly correlated with carbon content as expected.
相似文献With the increasing depth of underground engineering, the risk of coal–rock dynamic disasters such as rockburst is becoming more and more serious and complex, which seriously threatens the safety of coal resource, mine production and the surface ecological environment. However, the existing risk indices and methods used for evaluating rockburst risk cannot be fully applied to deep goal seam group (DCG) mining. For the safe exploitation of coal resources, in this paper, based on statistical analyses of 300 cases of rockburst, six new indices are proposed for evaluating rockburst risk in the DCG, namely dip angle, moisture content, stability of coal seam, advancing speed of working face, disturbance factors and support patterns. In addition, the influence of multiple factors coupling and superposition on rockburst risk was considered. Thus, the Comprehensive Index Method of rockburst risk of Deep Coal seam Group (DCG–CIM) based on analytic hierarchy process was established. Finally, rockburst risk in the evaluation area was quantitatively assessed into four grades, including “No rockburst risk”, “Weak rockburst risk”, “Medium rockburst risk” and “Strong rockburst risk”. Taking the 2233 working face of Hengda Coalmine as an example, the evaluation results show that the ranges of 0–184 m, 224–284 m, 324–384 m, 424–484 m, 524–584 m and 594–624 m from terminal line of haulage roadway on 2233 working face were the medium rockburst risk zones, which are in accordance with the on-site impact damage results and are more accurate than the traditional method. The DCG–CIM can consider more inducing factors and obtain more accurate and reliable evaluation results and is more suitable for deep coal seam group mining.
相似文献Mining-induced tremors are indispensable events that gestate and trigger coal bursts. The radiated energy is usually considered a key index to assess coal burst risk of seismic events. This paper presents a model to assess coal burst risk of seismic events based on multiple seismic source parameters. By considering the distribution and relation laws of the seismic source parameters of coal bursts, the model aims to identify dangerous seismic events that more closely match the characteristics of multiple seismic source parameters of coal bursts. The new coal burst risk index T is proposed. It consists of the similarity index SI (representing the similarity degree of relations between seismic events and coal burst events based on seismic source parameters) and the strength index ST (representing the burst strength of seismic events). We studied 79 coal burst events that occurred during extraction in LW250105 of the Huating coal mine in Gansu Province, China. We obtained the distribution and relation laws of multiple seismic source parameters of coal burst events to establish SI and ST. Two groups of seismic events with different energy distributions were examined to compare the assessment results based on the new model and energy criteria. The results show that 80% and 89% of seismic events with strong coal burst risk in Groups A and B, respectively, were coincident, and the seismic events with medium coal burst risk were slightly less compared to those based on radiated energy. The results indicate that the assessment based on the T value is a modification and optimization of that based on radiated energy. This model is conducive to improving the efficiency of monitoring and early warning of coal burst risk.
相似文献Gas emission from the working face in a gas-bearing coal seam impairs safe production. Especially in the coal face, influenced by mining, pressure-relief gas in adjacent seams flows into the working face through the goaf. Moreover, caved overlying strata in different regions show differences in pore and seepage characteristics. Thus, the caving of overlying strata in the goaf of a working face was explored by carrying out physical similarity simulation. Then, based on the characteristics of the geometric shapes of caved overlying strata after mining, a trapezoidal three-dimensional model for gas extraction was established. According to the calculation result, the parameters of field high-level boreholes were optimized. Then, the controllability of gas concentration at the working face after gas extraction was assessed by applying statistical process control. The result showed that after the observed surface of the physical similarity model was lightened, it was more favorable for conducting the test. Moreover, the maximum gas concentration in the goaf was negatively correlated with the diameter of high-level boreholes and the negative pressure for gas extraction. A statistical process control chart revealed that the gas concentrations at the working face were safe after gas extraction based on high-level boreholes, which also validated the feasibility and effectiveness of the model.
相似文献This study aimed to investigate the influence of local frequent dynamic disturbance on micro-structure evolution in different zones of coal-rock. To do so, we carried out a systematic experimental research on the micro-structure evolution of briquette and raw coal samples under local impact load by using self-developed pendulum hammer dynamic impact loading test device of coal-rock and ultrasonic testing equipment, and analyzed the localization effect of local impact load. The results show that Mn (micro-structure cumulative change factor) of briquette coal samples presents an inclined M-shaped four-stage evolution mode along and perpendicular to impact direction with cyclic impact times under conventional full impact load, whereas it shows more obvious anisotropy and localization under local impact load. Mn for both conventional full impact and local impact shows a nonlinear increasing trend with the increase in impulse, but their increasing gradients are different. The critical zone is the most affected, the impact zone comes next, and the non-impact zone is the least affected with the increase in impulse under local impact load. Mn in the impact zone and critical zone decreases exponentially with the increase in the impact loading area, while it increases exponentially in the non-impact zone. The micro-structures evolution in briquette and raw coal samples is similar, but the anisotropy and localization effect of micro-structure evolution for raw coal samples are more significant and more sensitive to the impact loading area. The micro-structure evolution of coal-rock under local impact load shows obvious localization effect. Mn in the critical zone is usually the largest, Mn in the impact zone is slightly less than that in the critical zone, and Mn in the non-impact zone is the least. The larger the impact loading area, the wider the influence enhancement area, and the smaller the non-influence area, yet the smaller the impact zone and critical zone are affected by local impact load.
相似文献A total of 14 vertical electrical soundings using Schlumberger electrode configuration and the complementary laboratory analysis of aquifer samples were carried out in the Abak Local Government Area of Akwa Ibom State, the coastal region of Nigeria. The study focused on the estimation of geohydrodynamic parameters of the frequently exploited aquifers and the implication of hydrodynamic parameters on the lithostratigraphy and the anticipated exposure of the assessed geologic formation at the shorelines. These parameters were porosity (?), tortuosity (τ), formation factor (F), aquifer water formation resistivity (Rw) and coefficient of permeability/hydraulic conductivity (K). Computation of the effective porosities from the aquifer cuttings was carried out using wet weight–dry weight technique and petrophysical techniques. The F values were computed using the aquifer formation bulk resistivity measured from field 1-D resistivity data analysis, whose interpretation was constrained by nearby borehole information. The formation pore water resistivities were estimated from the laboratory using electrical resistivity metre. The Win RESIST software program was used in interpreting the field data electronically. The results of interpretation gave the primary parameters of saturated and unsaturated units of the coastal regions used in this work. The area generally shows seemingly high porosity with high coefficient of permeability. The primary and secondary parameters have been contoured to model their distributions. Besides, some functional relations have been realized through regression analyses. The contour distribution of the geohydrodynamic parameters indicates the vulnerability of the water repositories to contaminations as well as the vulnerability of the shoreline to waterborne erosion. The seemingly high effective porosity in the compliant laboratory and calculated values indicate that the coastal region is neither lithified nor compacted/consolidated. This signals the possibility of the formation to be easily eroded, weathered or flooded where these units are exposed to water current. With these revelations, the shorelines could be properly managed and conserved by geotechnically reinforcing with hard and water-resistant concrete that can protect the vulnerable and erosion-prone porous sediments.
相似文献Air over-pressure (AOp) is one of the products of blasting operations for rock fragmentation in open-pit mines. It can cause structural vibration, smash glass doors, adversely affect the surrounding environment, and even be fatal to humans. To assess its dangerous effects, seven artificial intelligence (AI) methods for predicting specific blast-induced AOp have been applied and compared in this study. The seven methods include random forest, support vector regression, Gaussian process, Bayesian additive regression trees, boosted regression trees, k-nearest neighbors, and artificial neural network (ANN). An empirical technique was also used to compare with AI models. The degree of complexity and the performance of the models were compared with each other to find the optimal model for predicting blast-induced AOp. The Deo Nai open-pit coal mine (Vietnam) was selected as a case study where 113 blasting events have been recorded. Indicators used for evaluating model performances include the root-mean-square error (RMSE), determination coefficient (R2), and mean absolute error (MAE). The results indicate that AI techniques provide better performance than the empirical method. Although the relevance of the empirical approach was acceptable (R2?=?0.930) in this study, its error (RMSE?=?7.514) is highly significant to guarantee the safety of the surrounding environment. In contrast, the AI models offer much higher accuracies. Of the seven AI models, ANN was the most dominant model based on RMSE, R2, and MAE. This study demonstrated that AI techniques are excellent for predicting blast-induced AOp in open-pit mines. These techniques are useful for blasters and managers in controlling undesirable effects of blasting operations on the surrounding environment.
相似文献This paper describes the application of an unsupervised clustering method, fuzzy c-means (FCM), to generate mineral prospectivity models for Cu?±?Au?±?Fe mineralization in the Feizabad District of NE Iran. Various evidence layers relevant to indicators or potential controls on mineralization, including geochemical data, geological–structural maps and remote sensing data, were used. The FCM clustering approach was employed to reduce the dimensions of nine key attribute vectors derived from different exploration criteria. Multifractal inverse distance weighting interpolation coupled with factor analysis was used to generate enhanced multi-element geochemical signatures of areas with Cu?±?Au?±?Fe mineralization. The GIS-based fuzzy membership function MSLarge was used to transform values of the different evidence layers, including geological–structural controls as well as alteration, into a [0–1] range. Four FCM-based validation indices, including Bezdek’s partition coefficient (VPc) and partition entropy (VPe) indices, the Fukuyama and Sugeno (VFS) index and the Xie and Beni (VXB) index, were employed to derive the optimum number of clusters and subsequently generate prospectivity maps. Normalized density indices were applied for quantitative evaluation of the classes of the FCM prospectivity maps. The quantitative evaluation of the results demonstrates that the higher favorability classes derived from VFS and VXB (Nd?=?9.19) appear more reliable than those derived from VPc and VPe (Nd?=?6.12) in detecting existing mineral deposits and defining new zones of potential Cu?±?Au?±?Fe mineralization in the study area.
相似文献